Panasonic Projector Pt Ae1000u Operating Instructions

ENGLISH - 41
Maintenance
Care and Replacement
 Ensure the projector is switched off.
 Unplug all the cables from the projector.
JCleaning the outer surface of the projector
Wipe off dirt and dust gently with a soft cloth.
 If it is difficult to remove the dirt, soak a cloth in a neutral detergent diluted with water, wring the cloth well 
and then wipe the projector. Dry off the projector with dry cloth.
 If you use a chemical treated wipe, follow the instructions supplied with it.
JCleaning the lens...

Care and Replacement
42 - ENGLISH
Maintenance
 Ensure the projector is switched off.
 Unplug all the cables from the projector.
 Prepare a Phillips-head screwdriver.
 Contact an Authorized Service Center to purchase a replacement Lamp unit (ET-LAE1000).
The Lamp unit is consumable and the brightness decreases by duration of usage. The LAMP indicator will alert 
you of the replacement timing at 1 800 hours, and at 2 000 hours, the projector will be turned off. 1 800 or 
2 000 hours is a rough guidance and...

Care and Replacement
ENGLISH - 43
Maintenance
JRemoving and replacing the lamp unit
1. Use a Phillips screw driver to loosen the 3 lamp unit fixing 
screws until the screws turn freely. 
2. Hold the handle of the lamp unit and release the lamp unit 
lock.
3. Pull out the lamp unit gently from the projector.
4. Replace the new lamp unit while making sure that the 
direction of insertion is correct.
 Press the top of the lamp unit and make sure the unit is 
installed securely.
5. Tighten the lamp unit...

44 - ENGLISH
Maintenance
Troubleshooting
Should any problem persist, contact your dealer.
ProblemCauseReference 
page
Power does not turn on. The power cord may not be connected.
 The MAIN POWER switch is turned off.
 No electric supply is at the wall outlet.
 TEMP indicator is lit or flashes.
 LAMP indicator is lit or flashes.
 The lamp unit cover has not been securely installed.19
20
19
40
40
42
No picture appears. The video signal input source may not be connected to a 
terminal properly.
 The input...

ENGLISH - 45
Appendix
Technical Information
List of compatible signals
Mode
Display 
resolution 
(dots)
*1
*1. The “i” appearing after the resolution indicates an interlaced signal.
Scanning 
frequencyDot clock 
frequency
(MHz)Picture 
quality
*2
*2. The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture is projected.
FormatH
(kHz)V
(kHz)
NTSC/NTSC 4.43/
PA L - M / PA L 6 0720 x 480i...

Technical Information
46 - ENGLISH
Appendix
The serial connector which is on the connector panel of the projector conforms to the RS-232C interface 
specification, so that the projector can be controlled by a personal computer which is connected to this connecter.
JConnection
JPin assignments and signal names
JCommunication settings
Serial terminal
NOTE:
 You must use only an RS-232C Serial Interface Cable with a ferrite core, type ET-ADSER.
Pin No.Signal nameContents
ANC
BTXD Transmitted data
CRXD...

Technical Information
ENGLISH - 47
Appendix
JControl commands
CommandControl contentsRemarks
PONPower ONIn standby mode, all commands other than the PON command are 
ignored.
 The PON command is ignored during lamp ON control.
POFPower OFF If a PON command is received while the cooling fan is operating after 
the lamp has switched off, the lamp is not turned back on again straight 
away in order to protect the lamp.
IISINPUTParameter: (page 23)
VID = VIDEO IN
RG1 = PC IN
CP2 = COMPONENT1 INSVD = S-VIDEO...

Technical Information
48 - ENGLISH
Appendix
JInquiry commands
JBasic format
 The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds 
before sending the command.
 If sending multiple commands, check that a response has been received from the projector for one command 
before sending the next command.
 When a command which does not require parameters to be sent, the colon (:) is not required.
 If an incorrect command is sent from the personal computer, the...

Technical Information
ENGLISH - 49
Appendix
 Sub-menu items vary according to the selected input signal.
Menu structure
TYPE1
TYPE2
TYPE3
POSITION Menu ...................... 34H
H - POSITION........................ 34H
V - POSITION ........................ 34H
DOT CLOCK.......................... 34H
CLOCK PHASE ..................... 34H
ASPECT ................................ 35H
WSS ...................................... 36H
OVER SCAN ......................... 36H
KEYSTONE ..............................

50 - ENGLISH
Appendix
Specifications
Power supplyAC 100 - 240 V 50 Hz/60 Hz
Power consumption240 W
During standby (when fan is stopped): 0.08 W
Amps2.8 A - 1.2 A
LCD panel
Panel size (diagonal)0.74 type (17.78 mm)
Aspect ratio16 : 9
Display method3 transparent LCD panels (RGB)
Drive methodActive matrix method
Pixels2 073 600 (1 980 x 1 080) x 3 panels
LensMotorized zoom (2x)/Motorized focus
F 1.9 - 3.2, f 22.4 mm - 44.4 mm
LampUHM lamp (165 W)
Luminosity1100lm
Scanning frequency*1
(for RGB signal)
*1....