Panasonic Pedestal For Plasma Display TY-ST50VX100 Installation Instructions

							МОНТАЖ ПОВИНЕН  ВИКОНУВАТИСЬ  СПЕЦІАЛІСТАМИ .
КОМПАНІЯ  PANASONIC НЕ  НЕСЕ ВІДПОВІДАЛЬНОСТІ  ЗА БУДЬ-ЯКІ ПОШКОДЖЕННЯ  ВЛАСНОСТІ 
ТА /АБО  СЕРЙОЗНІ  ТРАВМИ, ВКЛЮЧАЮЧИ  СМЕРТЬ, ЩО Є НАСЛІДКОМ  НЕВІДПОВІДНОГО  МОНТАЖУ 
АБО  НЕПРАВИЛЬНОГО  ОБСЛУГОВУВАННЯ .
Деталі для складання (Перевірте  наявність усіх деталей  перед складанням )
  Кріпильні  гвинти 
стійок  підставки  (4) 
(сріблясті )  Гвинти для  кріплення  
стійок  підставки  до 
дисплея  (4)
 
(чорні )
  Стійки  підставки  
(2)  Основа  підставки  (1)
M5 × 18M5 × 30
LR
  Монтаж  п’єдесталу
Використовуйте  чотири кріпильні  гвинти стійок 
підставки  
 для надійного  закріплення  лівої та 
правої  стійки  на основі  підставки .
z  Переконайтеся , 
 що гвинти  щільно  затягнуто .
z   Затягування  
 кріпильних гвинтів стійок підставки  у 
неправильному  напрямку пошкодить  різьбу.
z   Нижня  частина  стійки підставки  
 має позначку  “L” 
або  “R”.
A
R
DL
Передній  
бік
   Закріплення  дисплея
Для надійного  закріплення  дисплея  використовуйте  
гвинти  для кріплення  стійок підставки  до дисплея  
.
z  Переконайтеся , 
 що гвинти  щільно  затягнуто .
z   Операцію  виконуйт
 е на горизонтальній  рівній 
поверхні .
D
B
Вигляд знизу
Позначка  
стрілки
Отвір  для встановлення  п’єдесталу
21
Українська 
						

							Dimension diagram / Abmessungen / Afmetingen /
Diagramma delle dimensioni / Dimensions / 
Diagrama de dimensiones / Måttdiagram / Dimensioner / 
Диаграмма размеров / Розміри
Units : mm (inches)
Einheit : mm
Eenheid : mm
Unità : mm
Unité : mm
Unidades : mm
Enhet : mm
Enhed : mm
Единицы  : мм
Одиниці  : мм
738 (29.1)
684 (27.0)
92.7 (3.7) 45 (1.8)
387 (15.3)
409 (16.1)
171 (6.8)
243 (9.6)
223 (8.8)58 (2.3)
750 (29.6)
50 (2.0)61 (2.4)70 (2.7)
22 
						

							Memo : 
						

							M1208A0 (PBS)
© Panasonic Corporation 2008
Web Site : http://panasonic.net 
						

							Accenta/Optima Engineer’s Manual
21
Test Outputs
3 = Set Up System Flags
The System Flags are divided into Flags 1, 2 or 3.
LCD Keypad:
• Press [up arrow] to display menu Set Up System Flags.
• Press [3] or [SET] to display the next screen.
LED Keypad:
• Press [3].  LED’s 1, 2 and 3 are ON.
Flag 1
NOTE: Pressing the [9] button sets all flags ON. Pressing the
[0] button sets all flags OFF. Pressing the [RESET]
button leaves the function.
LCD Keypad:
• Press [1] to display first option of System Flag 1. Press [1]
to toggle flag ON or OFF.
• Press [1-8] or [up arrow] to go to another option
under Flag 1.
• Press [SET] to save change then [RESET] to leave menu
or
Press [RESET] twice to leave menu.
.
LED Keypad:
• Press [1] to show status of first option of System Flag 1.
Press [1] or [PROG] to toggle flag ON or OFF.
• Press [1-8] to go to another option of Flag 1.
• Press [SET] to save change then [RESET] to leave menu
or
Press [RESET] twice to leave menu.
.
System Flags System FlagsSystem Flags System Flags
System Flags
1, 2 or 3? 1, 2 or 3?1, 2 or 3? 1, 2 or 3?
1, 2 or 3?
Set Up Set UpSet Up Set Up
Set Up
System Flags System FlagsSystem Flags System Flags
System Flags[up arrow]
[3] or [SET]
[1]
Silent PA Silent PASilent PA Silent PA
Silent PA
NO NONO NO
NO
RKP PA RKP PARKP PA RKP PA
RKP PA
YES YESYES YES
YES[1-8] or [up arrow]
[SET] then [RESET]
Set Up Set UpSet Up Set Up
Set Up
System Flags System FlagsSystem Flags System Flags
System Flags
1234
5
678
[1]
[1-8]
[SET] then [RESET]
1234
5
678
1234
5
678
1234
5
678
[3] 
						

							Accenta/Optima Engineer’s Manual
22
System Flags
Flag 1 - Options
There are eight options under Flag1 which are described below:
1 = Silent PA
When this flag is set to ON, operating PA will cause a silent PA alarm. Pressing the [1] button toggles the flag
ON or OFF.
2 = RKP PA
When this flag is set to ON, the keypad PA buttons are enabled. Pressing the [2] button toggles the flag ON
or OFF.
3 = Engineer Reset
When this flag is set to ON, an engineer code must be entered to reset the system after Tamper, PA or Fire
alarm. When the flag is set to OFF the system can be reset by the user. Pressing the [3] button toggles the flag
ON or OFF.
4 = PA User Reset
When this flag is set to ON, it permits the user to reset the system after a PA alarm, by pressing the [RESET]
button. The user can reset the system even if the Engineer Reset flag is set to ON. Pressing the [4] button
toggles the flag ON or OFF.
5 = Fire User Reset
When this flag is set to ON, it permits the user to reset the system after a Fire alarm by pressing the [RESET]
button. The user can reset the system even if the Engineer Reset flag is set to ON. Pressing the [5] button
toggles the flag ON or OFF.
6 = Bells in Fire
When this flag is set to ON, the external siren Bell box will sound two seconds On/two second Off during the
fire alarm. Pressing the [6] button toggles the flag ON or OFF.
7 = Zone 7 Fire
When this flag is set to ON it permits zone 7 to be used as a Fire zone. Pressing the [7] button toggles the flag
ON or OFF.
8 = Zone 8 Fire
When this flag is set to ON it permits zone 8 to be used as a Fire zone. Pressing the [8] button toggles the flag
ON or OFF. 
						

							Accenta/Optima Engineer’s Manual
23
Flag 2
NOTE:Pressing the [9] button sets all flags ON. Pressing the [0] button sets all flags OFF. Pressing the
[RESET] button leaves the function.
Accenta Optima Accenta OptimaAccenta Optima Accenta Optima
Accenta Optima
Version 1.00 Version 1.00Version 1.00 Version 1.00
Version 1.00F130-01-101 F130-01-101F130-01-101 F130-01-101
F130-01-101Build 101 (01)R Build 101 (01)RBuild 101 (01)R Build 101 (01)R
Build 101 (01)R
Date May 05 2006 Date May 05 2006Date May 05 2006 Date May 05 2006
Date May 05 2006 System and
software versionPart No
for software
English
Version
BuildBuild
Flag 2 - Options
Single Key Set
When this flag is set to ON, it allows the panel to be set by pressing the [SET] button. A code entry is not
required. However, a 4-digit code is required to Unset the panel. Pressing the [1] button toggles the flag ON
or OFF.
Strobe on Set
When this flag is set to ON, the external strobe will stay on for five seconds once the panel has set. Pressing
the [2] button toggles the flag ON or OFF.
Flag 3
 Flag 3 shows the Software Version of the panel and may be requested when contacting technical support.
Use the up arrow to scroll through the screens.
LCD keypad only: Example information you may see: LCD Keypad:
• Press [2] to select System Flag 2. Press [1-2]
or [SET] to toggle flag on or off.
• Press [up arrow] or [2] to go to second option
of Flag 2.
• Press [SET] to save changes and then [RESET] to
leave menu or press [RESET] twice to leave the menu.
LED Keypad:
• Press [2] to select of System Flag 2. Press [1-2] to toggle
flag ON or OFF.
• Press [1] and [2] to enable the first and second option of
Flag 2.
• Press [SET] to save changes and then [RESET] to leave
menu or press [RESET] twice to leave the menu.
Strobe on Set Strobe on SetStrobe on Set Strobe on Set
Strobe on Set
NO NONO NO
NO[2]
[up arrow] or [2]
Single Key Set Single Key SetSingle Key Set Single Key Set
Single Key Set
Yes YesYes Yes
Yes
Set Up Set UpSet Up Set Up
Set Up
System Flags System FlagsSystem Flags System Flags
System Flags[SET] then [RESET]
[2] then [1-2]
[1-2]
[SET] then [RESET]
System Flags (cont’d)
1234
5
678
1234
5
678
1234
5
678 
						

							Accenta/Optima Engineer’s Manual
24
6 = Set Up Zone Names
This  option allows each of the eight zones to be given a name from the library (Appendix 2).
4 = Set Up Time and Date
LCD Keypad:
This option allows the Time or Date to be modified. Pushing button [4] selects the option and the first screen
appears as typically below:
Time and Date Time and DateTime and Date Time and Date
Time and Date
Time?  Time? Time?  Time? 
Time? 
1 11 1
1
3:46:17 3:46:173:46:17 3:46:17
3:46:17 The Time can be modified in hours, minutes and seconds in the format
HH:MM:SS. The number keys on the keypad 0-9 are used for this
function. As each digit is modified the cursor moves to the next one.
When the time is correct press the [SET] button to accept the change
and move to the next screen.  To cancel the change press the
[RESET] button.
Time and Date Time and DateTime and Date Time and Date
Time and Date
Date?  Date? Date?  Date? 
Date? 
1 11 1
1
7-05-06 7-05-067-05-06 7-05-06
7-05-06 The Date can be changed in day , month, year format DD-MM-YY.
The number keys on the keypad 0-9 are used for this function. As each
digit is modified the cursor moves to the next one. When the date is
correct press the [SET] button to accept the change.  To cancel the
change press the [RESET] button.
Time & Date
LED Keypad:
If required, the time and date can be entered as per the procedure for the LCD keypad. However no informa-
tion will be indicated on the LED keypad. The only indication on the LED keypad that you are in menu 4 Set
up Time and Date is that LED’s 1 to 6 on the LED Keypad will be ON.
LCD Keypad:
• Press [up arrow] or to go to menu Set Up Zone Names.
• Press [6] or [SET] to go to zone 1 descriptor.
• Press [SET] to scroll through the library to the desired
descriptor.
• Press the [up arrow] to go to the next zone.
• To assign additional zone descriptors repeat the above procedure.
• Press [RESET] to save programming and leave the function.
LED Keypad:
The LED keypad cannot program zone names.
NOTE:The [up arrow] is not available on the LED keypad.
1: New Descriptor 1: New Descriptor1: New Descriptor 1: New Descriptor
1: New Descriptor   [SET]
1: Descriptor 1: Descriptor1: Descriptor 1: Descriptor
1: Descriptor[6] or [SET]
[RESET]
6>Set Up 6>Set Up6>Set Up 6>Set Up
6>Set Up
  Zone Names   Zone Names  Zone Names   Zone Names
  Zone Names
6>Set Up 6>Set Up6>Set Up 6>Set Up
6>Set Up
  Zone Names   Zone Names  Zone Names   Zone Names
  Zone Names[up arrow] 
						

							Accenta/Optima Engineer’s Manual
25
Timers
LCD keypad:
To change the Bell Time from 15 to 20 minutes:
•Press [up arrow] for menu Set Up Timers.
•Press [7] or [SET] for option 71 Set up Bell Time.
•Press [1] or [SET]. The Bell Time in minutes is displayed.
• The cursor is under the first digit. Select [2].
• The cursor moves to the second digit. Select [0].
• To accept the change press [SET] then [RESET]
OR to cancel the change press the [RESET] button twice.
7 = Set Up Timers
This option allows the Bell Time, Bell Delay and Rearm Count to be changed.
NOTE:The [OMIT] key takes you back to the first digit.
71 = Set Up Bell Time
This is the duration that the external bell output is active. The range is 01-99 minutes.  The default is
15 minutes.
LED keypad:
To change the Bell Time from 15 to 20 minutes:
•Press [7] or [SET] for option 71 Set up Bell Time.
•Press [1] or [SET] for Bell Time in minutes. LED’s 1 and 2
are on.
•Select [2] then [0]. LED’s 1 and 2 are on.
•To accept the change press [SET] then [RESET].  LED’s 1, 2 and
3 are on.
•OR to cancel the change press the [RESET] button twice.[7]
or [RESET]
[1] or [SET]
[SET] then [RESET]
1234
5
678
1234
5
678
7>Set Up 7>Set Up7>Set Up 7>Set Up
7>Set Up
  Timers   Timers  Timers   Timers
  Timers
Bell Time Bell TimeBell Time Bell Time
Bell Time
Minutes? 15 Minutes? 15Minutes? 15 Minutes? 15
Minutes? 15[1] or [SET]
71>Set Up 71>Set Up71>Set Up 71>Set Up
71>Set Up
   Bell Time    Bell Time   Bell Time    Bell Time
   Bell Time[7] or [SET]
7>Set Up 7>Set Up7>Set Up 7>Set Up
7>Set Up
  Timers   Timers  Timers   Timers
  Timers [SET] then [RESET] or [RESET]
[up arrow]
Bell Time Bell TimeBell Time Bell Time
Bell Time
Minutes? 20 Minutes? 20Minutes? 20 Minutes? 20
Minutes? 20
[2] and [0]
1234
5
678
1234
5
678 
						

							Accenta/Optima Engineer’s Manual
26
Timers (cont’d)
LCD keypad:
 To change the Bell Delay time from 00 to 12 minutes:
•Press [up arrow] for menu Set Up Timers.
•Press [7]or [SET]. Option 1 Set up Bell Time appears.
•Press [2]. The Bell Delay time in minutes is displayed.
• The cursor is under the first digit. Select [1].
• The cursor moves to the second digit. Select [2].
• To accept the change press [SET] then [RESET]
OR to cancel the change press the [RESET] button twice.
72 = Set Up Bell Delay
This delays the activation of the Bell for the required time. The range is 00-99 minutes. The default is 00
minutes.
NOTE:The Bell Delay delays the bell for one rearm period only. After rearm all alarms are immediate.
LED keypad:
 To change the Bell Delay time from 00 to 12 minutes:
•Press [7] to enter Set up Timers.LED’s 1, 2 and 3 are
on.
•Press [2] for Bell Delay time in minutes. LED’s 1and 2
are on.
•Select [1] then [2]. LED’s 1 and 2 are on.
•To accept the change press [SET]. LED’s 1, 2 and 3
are on. Press [RESET].
OR to cancel the change press the [RESET] button
twice.[7]
[SET] then [RESET] [2]
1234
5
678
1234
5
678
or [RESET]
1234
5
678
1234
5
678
7>Set Up 7>Set Up7>Set Up 7>Set Up
7>Set Up
  Timers   Timers  Timers   Timers
  Timers
Bell Delay Bell DelayBell Delay Bell Delay
Bell Delay
Minutes? 00 Minutes? 00Minutes? 00 Minutes? 00
Minutes? 00[2]
71>Set Up 71>Set Up71>Set Up 71>Set Up
71>Set Up
   Bell Time    Bell Time   Bell Time    Bell Time
   Bell Time[7] or [SET]
7>Set Up 7>Set Up7>Set Up 7>Set Up
7>Set Up
  Timers   Timers  Timers   Timers
  Timers [SET] then [RESET] or [RESET]
[up arrow]
Bell Delay Bell DelayBell Delay Bell Delay
Bell Delay
Minutes? 12 Minutes? 12Minutes? 12 Minutes? 12
Minutes? 12
[1] and [2]