Panasonic Pc Software Package Wv Asm100 Operating Instructions

							Cause/solution
81
• The value set for Maximum refresh interval (JPEG/
VGA) on the [Performance] tab of the System page
may not be appropriate.
Set an appropriate value for Maximum refresh interval
(JPEG/VGA) on the [Performance] tab of the System
page.
• The value set for Max bit rate (per 1 client) on the setup
menu of the camera that transmits MPEG-4 images may
not be appropriate for the CPU performance of the PC in
use.
Check the recommended settings of the camera when
operating MPEG-4 images.
Refer to the
setup instruc-
tions (PDF).
Refer to the
setup instruc-
tions (PDF).Reference 
pages
Symptom
• It may be possible that the PC in use does not meet the
system requirement.
Check the system requirements for a PC.
• It may be possible that the exceptional settings of
Windows Firewall are not configured.
Configure the exceptional settings of Windows Firewall.
• Depending on the communication status, the camera
icon cannot indicate the correct status of the camera.
When the camera icon displayed in the device tree or in
the map window is clicked, the camera icon will indicate
that the camera is online.
The camera icon displayed on the “Search” window or
on the “Download” panel will not change even when it is
clicked.
Refer to the
setup instruc-
tions (PDF).
Refer to the
setup instruc-
tions (PDF).
–
Image display is not per-
formed smoothly or stops.
(PC performance becomes
low.)
Cannot receive an alarm.
Live images are not dis-
played even when the cam-
era icon indicates that the
camera is online.
Live images are being dis-
played even when the cam-
era icon indicates that the
camera is offline. 
						

							82
Displayed messages and solutions
When starting the operation software
When a message window is displayed in the process of the startup, refer to the following to solve the problem.
When the [OK] button on the login window is clicked
When a message window is displayed by clicking the [OK] button on the login window, refer to the following to solve
the problem.• The operation software cannot be started when the setup software is
open.
Click the [OK] button, and then start the operation software after closing
the setup software.
• The hardware key is not inserted into the USB port of the PC.
Start the operation software after inserting the hardware key into the USB
port.
SolutionMessage
It is impossible to start the
operation software unless
the setup software is closed.
It is impossible to start the
operation software, because
the hardware key is not
found.
MessageSolution
• The default password has not been changed. It is recommended to
immediately change the password to enhance the security.
• Logged in with the password whose validation period is over. It is recom-
mended to immediately change the password to enhance the security. 
• The entered user name or password is incorrect. Enter the correct user
name and password.
Please change the ADMIN
password.
Please change the pass-
word.
Failed to log in. 
						

							83
When the [OK] button on the Change password window is
clicked
When a message window is displayed by clicking the [OK] button on the Change password window, refer to the fol-
lowing to solve the problem.
When the [OK] button is clicked on the window for a folder
designation
When a message window is displayed by clicking the [OK] button on the window for a folder designation, refer to the
following to solve the problem.
MessageSolution
• The entered characters for the password are less than 4 characters.
Enter 4 or more characters.
• The characters entered for the current password are incorrect. Enter the
current password correctly.
• The characters entered for New password and Enter the new password
again to confirm do not match. Enter the same password.
Enter more than 4 charac-
ters.
Incorrect current password.
Please enter the same pass-
word.
• This message will be displayed when the same file name already exists in
the selected folder.
Click the [OK] button to overwrite the existing file.
When the [Cancel] button is clicked, the window for a folder designation
will be displayed again.
SolutionMessage
The same file exists in the
selected folder. Are you sure
you wish to overwrite? 
						

							84
When an error occurred
When a message window is displayed at an error occurrence, refer to the following to solve the problem.
MessageSolution
• This message will be displayed when a critical error occurred. 
Restart the operating system of the PC.
When this problem is not solved even after the restart, reinstall the soft-
ware.
• This message will be displayed when no required data was found in the
database.
Import the backup data.
Please restart the operating
system. When this message
is displayed after the restart,
please reinstall the software.
Required data for DB was
not found. Please load the
backup data. When there is
no backup data, please rein-
stall or initialize the setup
data. 
						

							Basic operation
85
Operation in the terminal mode
The following are descriptions of how to operate an optional system controller in the terminal mode. It is possible to
restrict operable functions according to the user type (administrator or the registered users).
Important:
•Operation response may be slow when comparing with an analog system since operations are performed via a
network.
•Turn on the power of the system controller after confirming that this software started up.
•When the LAN cable is disconnected, a connection error with the system controller may occur.
•When the [ADJUST] button is pressed, a connection error with the system controller may occur.
Function/operation
Notes:
•[  ] indicates the button. When + exists between the buttons, press the both the buttons at once. When the indi-
cation → exists after an operation, the next operation is required to complete the operation.
•CDA Bof [Joystick], [JogDial], [Shuttle ring], [Zoom knob] indicate the operation direction of each interface.
Number/numeric value entryKey operation of the 
WV-CU950
Numeric keysNote
Cancel the entry [CLEAR]
Start the sequence display [TOUR SEQ]
Stop the sequence display [SEQ PAUSE]
Acknowledge the alarm [ACK]
[ALARM]•The same operation will be performed as when
the [Play] button on the alarm notification win-
dow is clicked. 
•The same operation will be performed as when
the [Live] button on the alarm notification win-
dow is clicked.
Reset an alarm
Determine
Cancel[ALM RESET]
[CAM(SET)]
[MON(ESC)]The same operation will be performed as when the
[ALM] button on the status bar is clicked.
The same operation will be performed as when the
[Enter] key of the PC keyboard is pressed.
The same operation will be performed as when the
[Esc] key of the PC keyboard is pressed. 
						

							86
Operate the camera
Basic operation
Preset position registrationKey operation of the 
WV-CU950
Enter a preset number →
[SHIFT] + [PRESET]Note
Move the camera to the preset
positionEnter a preset position num-
ber →[PRESET]When no preset position number is entered, the
camera will move to the home position.
Pan/tilt [Joystick CDA B] The displayed image will move to the direction in
which the joystick is tilted.
Adjust the brightness
• Set brighter
• Set darker
Adjust the focal point
• Set farther
• Set nearer
• Perform the auto focus func-
tion
Adjust the zoom
• Set to the wide side
• Set to the tele side[IRIS OPEN]
[IRIS CLOSE]
[FOCUS FAR]
[FOCUS NEAR]
[TOP]
[Zoom knob A]
[Zoom knob B]Adjustment of the brightness will continue until the
pressed button is released.
Adjustment of the focal point will continue until the
pressed button is released.
Zooming will continue until the zoom knob is being
rotated.
External control 1/2 

• Set AUX1 to ON
• Set AUX1 to OFF[AUX1 ON]
[SHIFT] + [AUX1 ON]•The mode setting can be configured on the
receiver. (Only the latch mode is available for
the cameras.)
•When setting for an event such as the sequence
display, set to the latch mode.
•Operation for AUX2 can be performed in the
same manner as for AUX1. 
						

							Basic operation
87
Playback of recorded images

• PAUSE
• FF
• REW
• NEXT IMAGE
• PREV IMAGE
• NEXT RECORD
• PREV RECORD
• Go to last
• STOP
• SKIP
• REV SKIP
Operate the recorder
Key operation of the 
WV-CU950Note
Start recording manually

• Stop the manual recording[REC]
[SHIFT] + [REC]
[PLAY/PAUSE]
[SHIFT] + [PLAY/PAUSE]
[Shuttle ring B]
[Shuttle ring A]
[JogDial B] during pausing
[JogDial A] during pausing
[JogDial B] while holding
down [SHUTTLE HOLD]
[JogDial A] while holding
down [SHUTTLE HOLD]
[GO TO LAST]
[STOP]
[+]
[-] 
						

							For U.S., Canadian and Puerto Rican fields:
Panasonic System Solutions Company, 
Unit Company of Panasonic Corporation of North America
Security Systems
www.panasonic.com/security
For customer support, call 1.877.733.3689
Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094
Zone Office
Eastern: Three Panasonic Way, Secaucus, New Jersey 07094
Central: 1707 N. Randal Road, Elgin, IL 60123
Southern: 1225 Northbrook Parkway, Suwanee, GA 30024
Western: 6550 Katella Ave., Cypress, CA 90630
Panasonic Canada Inc.5770 Ambler Drive,Mississauga, 
Ontario, L4W 2T3 Canada (905)624-5010
http://www.panasonic.ca
Panasonic Sales Company
Division of Panasonic Puerto Rico Inc.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina
P.R. 00985(809)750-4300
© 2007 Matsushita Electric Industrial Co., Ltd. All Rights Reserved. N0207-1027 V8QB6576BN       Printed in Japan
For European and other fields:
Matsushita Electric Industrial Co., Ltd.
Osaka, Japan
http://panasonic.net