Panasonic Part For Network Functions And SD Memory Card Functions PT-L735NTE Manual

							41
Presentation mode
When the user specifies a folder name in the folder selection at the left top, the
images in the folder will be listed in thumbnails if the folder contains image file(s)
(JPEG, PNG). If the system is in “PowerPoint →
Presentation” mode, the folder(s) of
converted images will be automatically selected.
PowerPoint Presentation mode
This function converts PowerPoint files (*.ppt) into image files so that they may be
transmitted to the projector.
From startup menu, execute [PowerPoint  Presentation mode], and a [Drag
and drop a PowerPoint file (*.ppt) here] message appears. Drag and drop the
desired PowerPoint file to the specified point on the screen.
Specify the destination folder for file saving, and this will automatically start
conversion into an image file. When all conversion is complete, a screen of
presentation mode appears. Here the user may check the list of converted
PowerPoint files.
For further operations, see the instructions on the presentation mode.
Setting of capture delay time
If your personal computer is too low in its ability, sometimes the PC screen image
may not be captured successfully. In such cases, adjust the delay time to the
optimal level. However, no need for this adjustment, normally.
Use of Wireless Manager 3.0 
						

							42
Presentation mode
Check [Presentation mode] and press the [Send] button.
When an image is sent, the next image will be automatically selected. In addition,
images can be changed over without delay of time because the next image has been
sent to the projector in advance. Furthermore, the projector cannot be connected by
other personal computers because it is already monopolized.
Progress bar
The bar chart indicates the progress while the image is transferred to the projector.
Switching display mode
Press the [ZOOM] button, and the image being projected on the projector screen
will be displayed by full image in the larger frame (i.e., the thumbnail viewing
frame) on the right and the next image will be displayed on the smaller preview
screen on the left.
Add:
This function allows the user to add images from different folders. Added images
will be placed to the last of the series of images in the thumbnail viewing frame.
Delete:
The user can delete the image(s) selected in the thumbnail viewing frame.
Note:
Deleted image files exist in the recycle bin of the personal computer. Accidentally
deleted files can be retrieved from the recycle bin.
Change of sequence:
Images can be replaced in the sequence by drag and drop operation in the
thumbnail viewing frame.
Use of Wireless Manager 3.0 
						

							43
Re-display:
This function updates images to the list of the latest thumbnail images. If any
image in a folder has undergone edit by Explorer etc., for example, the re-display
button will reflect the result in the thumbnail viewing frame.
Automatic play:
This function will project the images in the folder one after another at constant
time intervals in turn from the first one to the last.
Automatic play starts with the currently selected thumbnail image. During
automatic play, the [Automatic play] button changes into a [Pause] button. When
the [Pause] button is pressed, the next image remains selected for transmission.
However, if the [Stop] button is pressed, the display sequence will be refreshed
to the top image in the folder.
During automatic play, too, other personal computers cannot connect to the
projector because the projector is monopolized.
In addition, the user may make settings of image display interval and loop times
(display times) by going to [Option] →
[Others].
Timer:
Every press on the [START] button will change the function in turn as: [START]
→
[STOP] →
[RESET]. [START] activates the timer, [STOP] suspends the timer,
and [RESET] clears the timer to “0”. The user can use this function to check the
elapsed time in presentation for reference.
Communication with SD
([TRANSMIT], [RECEIVE]):
This function enables the user to
transmit all images in the folder of the
personal computer to the SD Memory
Card set in the projector, or inversely,
to retrieve images in the specified
folder on the SD Memory Card from
the personal computer.
When images are received, image
data will be saved in the selected
folder in the presentation mode
window.
Note:
Do not turn OFF the power to the projector main unit or remove the SD Memory
Card from the main unit when the system is in communication with the SD
Memory Card. Doing this may not only destroy the data, but also damage the SD
Memory Card itself.
Use of Wireless Manager 3.0 
						

							44
Other functions
Searching projector
This function is not required when Simple Connection
is used. The function becomes necessary when
Simple Connection is not used or if two or more
projectors are used.
Go to [Option] and specify the projector in
[Selection of projector].
[Search]:
The user can use this function to search the
projectors that are available for connection.
However, projectors subject to search are limited
to those within the same network.
Projectors that are not powered cannot be
searched.
Registering projector
Once a projector is registered, the next time the user can omit the procedure to
connect to the same projector.
If Simple Connection is used, the projector will be automatically registered. If Simple
Connection is not used, connection will be made to currently registered projector.
If two or more projectors have been registered, the one at the top in the registration
(or the projector connected on the previous occasion) will be specified the first for
connection. If any projector is not detected by the search, the user may use the [Add]
button to directly enter the IP address of the projector.
The host name to identify the projector will be automatically sent from the projector
and displayed. The host name should be set on the projector side.
Deleting projector
This function deletes the specified projector from the registration.
Confirming connection
This function checks the condition of connection to registered projectors.
Use of Wireless Manager 3.0 
						

							45
Displaying the sender, senders name
Checkmark [Show the sender] and enter the name in [Sender].
In meeting mode, the entered [Sender’s name] will be shown in combination at the
right bottom of image sent to the projector. The above information is not displayed in
live mode or in presentation mode. If [Presentation mode] is not checkmarked in
presentation mode, the information is displayed on each image transmission.
Setting a shortcut key
Go to [Option] and select [Others].
[Live mode]:
This function turns ON/OFF the live mode.
[Full screen transmission]:
This function transmits the entire image on the
PC screen to the projector.
[Presentation]:
Displays a presentation screen.
[Capture]:
Displays a capture screen.
Setting automatic play
See the section of automatic play of “presentation mode”.  (See page 43)
Setting Simple Connection
When Simple Connection is used, the user may disable the screen saver.
If the system hangs up due to any anomaly during Simple Connection, the user can
press the [Restore] button to bring the network settings into the previous state.
However, this cannot be guaranteed against all abnormal conditions.
Note:
The screen of Wireless Manager 3.0 must be activated when using the shortcut
key. Note that, if any other application is running at the same time, and when the
set shortcut key is also used by that application, then this function works in a
totally different way.
Use of Wireless Manager 3.0 
						

							46
Use of Web browser control
Browsing software (Internet Explorer etc) can be used to access the projector and
remote-control the projector from the personal computer, or to control the SD
Memory Card inserted in the projector.
Settings on the projector
Web control 
ON: enables Web browser control.
OFF: disables Web browser control.
Web power supply
ON: enables to turn on the lamp of the projector by Web browser control when
the system is on standby.
OFF: disables to turn on the lamp of the projector by Web browser control when
the system is on standby.
Use the POWER button of the projector or remote control to light the lamp.
Web password
Set a password within 16 alphanumeric characters. No password is set on factory
shipping.
When the personal computer accesses the projector, the password will be
queried. Then enter the password that was entered here.
Using [ ], select the [Web] password, and press [ENTER], and a software
keyboard will appear.
Press the [ ] button.
It is possible to change the settings using the
[•] buttons.
When alteration is complete, press the [ENTER]
button.3
Press the [MENU] button1
Using the [ ] buttons, display the
network settings screen.2 
						

							47
Use of Web browser control
Settings on the personal computer
Notes:
•  If Simple Connection is used, settings will be made automatically.
(Internet Explorer Ver.6.0 or superior is needed, though)
•  If a proxy server is already used, set the IP address of the projector to which
connection is made as an exception for not using a proxy server in [Advanced].
Note:
For Netscape, go to [Edit] →
[Setting] →
[Details] and enable JavaScript.
In Security, set the security level
to the Default level. Or otherwise,
from Custom level enable Active
script..3
Right-click the [Internet Explorer]
icon.
This opens Properties.
1
Go to [Connect To], open [LAN
settings], clear the checkmark on
“All options”, and click [OK].
Then the setting screen will be closed.
2 
						

							48
Operation of Web browser control
Starting Web browser control
Start the browser (Microsoft Internet Explorer is used as an example here), and enter
the IP address assigned to the projector.
Web browser control will be started.
Top screen
Note:
Web browser control can also be started from Wireless Manager 3.0.
While Wireless Manager 3.0 is running, right-click the icon shown on the task bar,
select and left-click  Remote Control.The Web browser control can also be started
by pressing the [CTRL] + [H] buttons at the same time. 
Note:
• In case you forget the password, assign a new password to the projector (For
security reason, the projector does not show the password that you have been
using).
• The top screen may not be displayed depending on the browser. In that case,
close the window first and start again the Web browser control, or press the
[CTRL] + [R]  buttons at the same time.
Use of Web browser control
Make setting so that the proxy server will not
be used.
(To use the proxy server, see page 47.)
Specify the IP address that has been assignedto the projector in the network setting.
Select Japanese or English.
Enter the password if any has been defined. 
						

							49
Projector control
Click Projector control in the menu.
The user can make various settings of the projector.
Basic control screen
Option control screen 
Notes:
• If the power supply has been turned ON, the screen will be closed for a moment.
Confirming the lamp is lighting, then enter into the top screen again.
• It may happen that connection to the projector is unsuccessful immediately after
the power is turned ON. Then, wait for a moment and try connection again.
• If Web control is not set to ON in the network setting of the projector, either basic
control or option control will not operate.
• If Web power is not set to ON in the network setting of the projector, the action of
turning ON the power will not be performed. However, the projector control
screen will provide the same display as that when normal operation is possible.
Note:
Monitor information is updated at regular intervals. If you go to Display and press
the Refresh button, you can check the current and accurate information.
Use of Web browser control 
						

							50
Monitor information screen
When power is turned ON:When the system is in Web standby state:
Note:
Monitor information is updated at regular intervals. If you go to Display and press
the Refresh button, you can check the current and accurate information. 
Use of Web browser control