Panasonic Outdoor Pan Tilt Head Aw Ph650 Operating Instructions

31

Connections
Example of connections when using a multi purpose camera

Iris operationAW-RP655AK-HRP150
AUTO AUTOAUTO
AK-HRP150 MANUAL AUTOMANUAL
AW-RP655 MANUAL MANUAL (
)—
 Set to MANUAL when using the presets and tracing memory.
•  
Since the iris control of the AK-HRP150 and AW-RP655 is not coordinated, it may vary significantly when it is operated 
initially after the controller used to exercise control has been switched.
•   The IRIS indicator on the AW-RP655 can be displayed only when the...

32

Limiters
Be absolutely sure to set the limiters (travel range) of the pan/tilt head before use. 
Depending on where the pan/tilt head system has been installed, obstacles may be 
present within the travel range with which the camera may come into contact.
 
Contact with any such obstacle by the camera may cause malfunctioning or 
accidents.
In this case, contact can be prevented by setting the limiters directly before any such 
obstacle.
Multi function controller (AW-RP655) is used to set the...

33

Limiters
 Releasing the limiters
The set limits can be release by taking the following steps. 
• Releasing the upper limit of operating range
1.   While holding down the OK button on the controller,  press TRACING/PRESET MEMORY button 47
.
2.   The release is completed when TRACING/PRESET  MEMORY button 50 [LIMIT OFF] lights.
• Releasing the lower limit of operating range
1.   While holding down the OK button on the controller,  press TRACING/PRESET MEMORY button 46
.
2.   The release is completed...

34

Replacement of consumable parts
 
Replacing the battery
The battery lasts for about 5 years.
The pan/tilt head stores the preset positions, limiter positions and other data in its memory. Although this data is retained even 
after the power has been turned off, it will be lost when the power is turned off once the battery has reached the end of its 
service life.
Replace the battery once it has lost its effectiveness. (The pan/tilt head uses a CR2032 manganese dioxide-lithium battery.)
  Removing...

35

Replacement of consumable parts
 Replacing the motor
Replace the motor when it ceases to operate properly.
For details on the motor replacement, consult your dealer.
 Replacing the belt
Replace the belt when the preset stop accuracy has deteriorated.
For details on the belt replacement, consult your dealer.
  Replacing the gear
Replace the gear when the preset stop accuracy has deteriorated.
For details on the gear replacement, consult your dealer.
The motor, gear and belt are consumables.
They...

36

Appearance
Unit: inch (mm)
20-1/8 (511)
6-11/16 (170)
8-3/8 (213)
6-11/16 (170)
9-5/16 (237)
5-7/8 (149)
13-1/8 (333)
5-1/2 (140)
7-1/2 (190)
6-5/16 (160)
3/16−ø3/8 (4−ø10) hole
Main unit 

37

9-11/16 (246)
Appearance
Unit: inch (mm)
27 (685)
10-1/2 (266)
1-7/8 (48)
Housing unit 

38

7-7/8 (200)
Appearance
Unit: inch (mm)
11 (280)
4-3/4 (121)
3/8 (10)
7/8 (22)
AC adapter unit
3-7/8 (98)
2-7/16 (62)
5-3/4 (146)
7-7/8 (200)
4-M8 nut 

39

Cable specifications
Connector:  10136-3000VE made by Sumitomo 3M
When an IAS, WAS or VAS lens (analog drive) made by Canon is used
Case:  10336-52F0-008 made by Sumitomo 3M
Connect to the LENS I/F2
 
connector in housing.The cable lengths are approximate. Ensure that their lengths are appropriate for the actual system used.
Connect to the FOCUS connector on lens.
Cable length: At least 800 mm or soConnect to the ZOOM connector on the lens.Cable length: At least 800 mm or so
Connect to the lens...

40

Cable specifications
Connector:  10136-3000VE made by Sumitomo 3M
When an IASD, WASD or VASD lens (digital drive) made by Canon is used
Case:  10336-52F0-008 made by Sumitomo 3M
Connect to the LENS I/F2
 
connector in housing.The cable lengths are approximate. Ensure that their lengths are appropriate for the actual system used.
Connect to the ZOOM/FOCUS
 
connector on lens.
Cable length: At least 800 mm or so
Connect to the lens cable.
Cable length: At least 500 mm or soConnect to the IRIS...