Panasonic Outdoor Pan Tilt Head Aw Ph650 Operating Instructions

11

Parts and their functions
AC adapter unit

 
 
 
 
 DC power unit
This unit supplies a DC output of 15 V, 10 A (maximum) 
when an AC input of 120 V is supplied.
 Power switch [POWER ON/OFF]
This switch is used to supply AC power to the DC power 
unit. Keep the switch in the ON position during use. 
 Fuse holder/fuse
A fuse for protecting the DC power unit is in the fuse 
holder. A burnt fuse may be caused by a DC power 
unit defect. In such a case, consult the store where you 
purchased...

12

Parts and their functions
Supplied cable unit



 
 
 
 24P round water-proof plug (male)
Connect this to the multi connector [MULTI] on the main 
unit.
 RJ-45 modular plug
Connect this to pan/tilt head controller. 
It can be extended up to 3281 ft. (1000 m). 
To extend the connection, use a relay adapter purchased 
on the market and use a 10BASE-T straight cable (UTP 
category 5) for the extension.
 VIDEO OUT BNC jack
This is the output connector for the camera’s video 
signals.
 
Use a...

13

Parts and their functions
 
 (VEEB0152)
 
 7P round water-proof plug (female)
Connect this to the power connector [POWER] on the 
main unit.
 7P round water-proof plug (male)
Connect this to the DC output connector [DC 15V OUT] 
on the AC adapter.
 
 (VEEB0176)
 26P connector (male)
Connect this to the CAMERA I/F connector [CAMERA 
I/F] on the housing.
 50P connector (male)
Connect this to the CAMERA I/F connector [CAMERA 
I/F] on the convertible camera.
  
 26P connector (male)
Connect...

14

Installation
Installing the housing mount frame
Attach the housing mount frame (supplied) to the rotary arm of the main unit.
  Attach the housing mount frame to the rotary arm as shown in the figure below. The screws must be installed together with 
the flat washers and spring washers (supplied).
 · Using the supplied Allen key, install the frame securely to prevent looseness in the four places where the screws are used.
Rotary arm

Allen key
Housing mount frame 

15

Installation
Cable compensation circuit settings
When the pan/tilt head and controller have been connected, the maximum allowable length of the connecting cables is 3281 ft. 
(1000 m) for the 10BASE-T straight cable (UTP category 5) and coaxial cable (BELDEN 8281). However, when using the cables 
beyond a distance of 1640 ft. (500 m), set the cable compensation circuit to ON by following the steps. (The factory setting is 
OFF.)
  Remove the five screws used to attach the sunshade cover to keep...

16

Installation
CPU circuit board switch settings
Set switches SW1, SW2 and SW3 on the CPU circuit board as follows.
  SW1 (Selector switch for landing characteristics)  
For a soft landing:  Set SW1 to the left position (RP501). (Factory setting)
  For an exact landing:  Set SW1 to the right position (RP605). 
  SW2 
Do not change the position of this switch. Continue to use it at the DESK TOP position.
  SW3 
Do not change the position of this switch. Continue to use it at the RS-422 position.
•...

17

Installation
How to install the camera
   
Loosen the bolts for opening and closing the top cover, 
and open the top cover.
Loosen the top cover open/close bolts
   Open the top cover until the support arm completely 
enters the groove. 
 
Bear in mind that it will not be possible to lock the top 
cover if the arm is not completely in.
The support arm completely enters  
the groove.
   Install the camera on the camera mount.
   For details on how to install the camera and mount, refer 
to the...

18

Installation

  Use the 2 screws 
 supplied with the camera to attach 
the mounting adapter  (supplied with the camera) to 
the top panel of the camera.
  Attach the positioning screw   (supplied) to the camera 
mounting spacer . 
  Use the 2 screws  (supplied) to attach the camera 
mounting spacer  to the mounting adapter  (supplied 
with camera) on the top panel of the camera.
   Attach the camera mount 
 to the camera mounting 
spacer  using the 2 screws , flat washers  and 
spring...

19

Installation

  Attach the positioning 1 screw  (supplied) to the 
camera mount 
.
   
Attach the camera mount  to the fan mounting part  
on the top panel of the camera
 using the 1 screw , flat 
washer 
  and spring washer  (supplied). (The camera 
mount points toward the front or back in the opposite 
way from a convertible camera. For pointing upward or 
downward, make sure that the two sides of the camera 
mount are lower than the central area that is attached.)
   Attach the lens to...

20


  Attach the positioning 1 screw  (supplied) to the 
camera mount 
.
   
Attach the camera mount   using the 2 screws , flat 
washers 
  and spring washers  (supplied).  
(The camera mount points toward the front or back in 
the opposite way from a convertible camera. For pointing 
upward or downward, make sure that the two sides of the 
camera mount are higher 
— which is the opposite from 
when the AK-HC910 is used — than the central area that 
is attached.)
   Attach the lens to the...