Panasonic Network System KX HNS107 Users Guide

							Access Keypad (KX-HNK101)
RAllows you to quickly confirm and change the system’s arm mode
R Can be wall mounted inside your home near the entrances and exits for easy access
21
Welcome to the Panasonic Home Network System!   
						

							Keychain Remote (KX-HNK102)
RAllows you to quickly change the system’s arm mode when you come home or are going out
R Can be used to trigger a pre-programmed operation, such as turning on a smart plug or sounding an
alert
R Can be attached to a set of keys for added convenience
22
Welcome to the Panasonic Home Network System!   
						

							Backup Battery (KX-HNP100)
RSupplies power to your hub or other devices in the event of a power outage
R Can be used to trigger the hub to call a pre-programmed phone number in the event of a power outage
23
Welcome to the Panasonic Home Network System!   
						

							Digital Cordless Handset (KX-HNH100)
RMakes and receives calls using your landline
R Can be used to change the system’s arm mode
R Displays system status
24
Welcome to the Panasonic Home Network System!   
						

							There are 4 basic steps you need to perform in order to access the system from your mobile device.Connections¯Connect your hub to a power outlet and to your telephone line. *1Download
¯Download the  [Home Network]  app to your mobile device.Initial setup
¯Use the  [Home Network]  app to configure the hub to connect to your
wireless router, and then register your mobile device to the hub.Register devicesAdd more mobile devices (smartphones and tablets), cameras,
sensors, and other devices to the system.
*1 Refer to the System Setup Guide included with your hub for more information.
Download information is available at the web page listed below.
{{"www.panasonic.net/pcc/support/tel/homenetwork/"|tolink("http://www.panasonic.net/pcc/
support/tel/homenetwork/")}}
Requirements
– Hub (KX-HNB600)
– A wireless router
– A compatible mobile device
Compatible mobile devices
– iPhone 4 and later, iPad (iOS 6.0 and later)
– Android smartphones and tablets (Android 4.0 and later)
– Minimum recommended screen size: 1280 ´720 (screen content may not be displayed properly on
devices with smaller screens)
Note:
R The  [Home Network]  app may not function properly depending on the system environment, such as
the model of your mobile device, the peripherals connected to your mobile device, and the apps
installed on your mobile device.
R The following Android devices are not compatible with the  [Home Network] app.
– Android devices that are not supported by Google Play
– Android devices with limited hardware features (Bluetooth, Wi-Fi, and microphone support are required.)
In order to use your mobile device to access the system, you must first configure the hub to access your
wireless router.
Note:
R If your hub is already configured to access your wireless router, you do not need to perform this
procedure again.
R If you have completed this procedure and want to register another mobile device to the hub, see
“Registering other mobile devices to the hub”, Page 28.
R If you experience trouble while performing this procedure, refer to the information in  “Sometimes I
cannot access the system while at home”, Page 110.
25
System setup 
						

							Before you begin
In this procedure, the hub will enter “temporary access point mode”. In this mode, you can connect your
mobile device directly to the hub using Wi-Fi®, and then use your mobile device to change the hub’s
Wi-Fi settings so that the hub can connect to your wireless router.
Confirm the following before you begin.
– Make sure you have installed the  [Home Network] app on your mobile device
– Make sure your wireless router and the hub are turned on and the hub’s LED indicator is lit in yellow
– Make sure the hub is located within range of your wireless router
– Make sure your mobile device is connected to your wireless router
– Make sure your mobile device can connect to the Internet
– Make sure you know the network name (SSID) and password assigned to your wireless router
Note:
R The hub only supports the 2.4 GHz wireless band. Before performing the initial setup, make sure your
mobile device is connected to the wireless router using the SSID that is assigned to the 2.4 GHz band
of your wireless router. When prompted to enter your wireless router’s password, enter the password
that is assigned to the 2.4 GHz band.
Initial setup for iPhone, iPad
1 Start the  [Home Network]  app by tapping its icon (shown below).
RThe end-user license agreement is displayed the first time you start the app.
R If your device is not compatible with the app, a message about incompatibility will be displayed
when you start the app.
2 Tap  [Set up the Hub] .
R A description of the initial setup procedure is displayed.
3 When prompted, press the  Wi-Fi SETUP button on the hub.
R The hub’s LED indicator blinks in yellow.
4 Change your mobile device’s Wi-Fi setting temporarily so that it connects to the hub directly.
R Open your mobile device’s  [Settings] app, tap [Wi-Fi], select “KX-HNB600_Panasonic”, enter
“00000000” as the password, and then tap  [Join].
R If more than one item named “KX-HNB600_Panasonic” is displayed, wait approximately
10 minutes and perform this procedure from the beginning.
5 Start the  [Home Network]  app again.
6 If necessary, enter the password required to connect to your wireless router and then tap  [Next].
R The hub and your mobile device connect to your wireless router.
R If prompted, follow the on-screen instructions and connect your mobile device to your wireless
router, start the app again, and then tap  [Add This Mobile Device].
R If you enter the wrong password,  [Setup failed.] is displayed and the hub’s LED indicator lights.
Proceed as follows according to the color of the hub’s LED indicator.
– If the LED indicator is lit in yellow, repeat the initial setup procedure from the beginning.
– If the LED indicator is blinking quickly in green, you must reset the hub’s Wi-Fi settings. See  “If the hub’s LED indicator blinks quickly in green”, Page 27.
R The hub’s MAC address is displayed on this screen. If your wireless router uses MAC address
filtering for extra security, make a note of the hub’s MAC address and add it to your wireless
router’s list of MAC address that are allowed to access the router.
7 When prompted, press the  Wi-Fi SETUP button on the hub.
R Your mobile device will be registered to the hub.
26
System setup   
						

							8When prompted, set the password used to log in to the hub while away from home and then tap  [OK].
9 When prompted, enter a name for your mobile device and then tap  [OK].
R This setting allows you to change the name assigned to your device. It can help you identify your
mobile device when performing certain operations, such as deregistering or making intercom calls
using a cordless handset.
10 When prompted, select whether you want to customize device profiles, i.e., the device name,
location, and other settings for your devices.
R If you choose not to customize the device profiles now, you can change them later if desired (see
“Setting device profiles (device names, locations, and other settings)”, Page 92).
R If you choose to customize the device profiles now, change each setting as desired. When
finished, tap 
 repeatedly until the “completed” message is displayed.
R The app’s home screen is displayed when initial setup is complete.
If the hub’s LED indicator blinks quickly in green
If you enter the wrong Wi-Fi password during the initial setup procedure for iPhone or iPad,  [Setup
failed.]  is displayed and the hub’s LED indicator blinks quickly in green. In this case, perform the
following.
1 Press and hold the 3 registration buttons on the side of the hub and the  Wi-Fi SETUP button on the
back of the hub at the same time (4 buttons total) until the hub’s LED indicator blinks slowly in green and yellow.
2 Wait for the hub’s LED indicator to light in yellow.
3 Repeat the initial setup procedure ( “Initial setup for iPhone, iPad”, Page 26).
Initial setup for Android devices
1 Start the  [Home Network]  app by tapping its icon (shown below).
RThe end-user license agreement is displayed the first time you start the app.
2 Tap  [Set up the Hub] .
3 When prompted, press the  Wi-Fi SETUP button on the hub.
R The hub’s LED indicator blinks in yellow.
R The app temporarily changes your mobile device’s Wi-Fi setting so that it connects to the hub
directly.
4 If necessary, enter the password required to connect to your wireless router and then tap  [Next].
R The hub and your mobile device connect to your wireless router.
R The hub’s MAC address is displayed on this screen. If your wireless router uses MAC address
filtering for extra security, make a note of the hub’s MAC address and add it to your wireless
router’s list of MAC address that are allowed to access the router.
5 When prompted, press the  Wi-Fi SETUP button on the hub.
R Your mobile device will be registered to the hub.
6 When prompted, set the password used to log in to the hub while away from home and then tap  [OK].
7 When prompted, enter a name for your mobile device and then tap  [OK].
R This setting allows you to change the name assigned to your device. It can help you identify your
mobile device when performing certain operations, such as deregistering or making intercom calls
using a cordless handset.
27
System setup    
						

							8When prompted, select whether you want to customize device profiles, i.e., the device name,
location, and other settings for your devices.
R If you choose not to customize the device profiles now, you can change them later if desired (see
“Setting device profiles (device names, locations, and other settings)”, Page 92).
R If you choose to customize the device profiles now, change each setting as desired. When
finished, press your device’s “back” button repeatedly until the “completed” message is displayed.
R The app’s home screen is displayed when initial setup is complete.
In order to access the system from a mobile device, you must first register the mobile device to the hub.
You can register 8 mobile devices to a hub.
Confirm the following before you begin.
– Make sure you have completed the initial setup procedure ( “Initial setup”, Page 25)
– Make sure your mobile device can connect to the Internet
– Make sure your wireless router and the hub are turned on
– Make sure your mobile device and the hub are connected to the same wireless router
1 Using the mobile device that you want to register, download the  [Home Network] app and then start
the app.
2 Tap  [Add This Mobile Device] .
R If the  [Home Network]  app home screen is displayed ( “Using the home screen”, Page 33), your
mobile device has already been registered to the hub. You do not need to perform this procedure.
3 When prompted, press the  Wi-Fi SETUP button on the hub.
R Your mobile device will be registered to the hub.
4 When prompted, enter the password used to log in to the hub while away from home ( “Login
password”, Page 99) and then tap  [OK].
5 When prompted, enter a name for your mobile device and then tap  [OK].
R This setting allows you to change the name assigned to your device. It can help you identify your
mobile device when performing certain operations, such as deregistering or making intercom calls
using a cordless handset.
6 When prompted, select whether you want to customize device profiles, i.e., the device name,
location, and other settings for your devices.
R If you choose not to customize the device profiles now, you can change them later if desired (see
“Setting device profiles (device names, locations, and other settings)”, Page 92).
R If you choose to customize the device profiles now, change each setting as desired. When
finished, tap 
 (iPhone, iPad) or your device’s “back” button (Android devices) repeatedly until
the “completed” message is displayed.
R The app’s home screen is displayed when registration is complete.
Note:
R To register other devices (cameras, sensors, etc.), see  “Registering devices”, Page 92.
R 8 mobile devices can be registered to the hub, however, only the first 4 can use phone features. If you
want to use phone features with an additional mobile device, use the procedure described in There are
more than 4 mobile devices registered to the hub. Page 116.
R For privacy, we recommend that you deregister your mobile device from the system (see
“Deregistering devices”, Page 92) before handing it over to a third party (such as when submitting
your mobile device for service, lending it to someone else, selling it, etc.), before registering your
mobile device to another hub, or if you no longer intend to use the mobile device with the system.
28
System setup  
						

							This section describes commonly used system features, the devices required for each example, and
briefly explains the required settings.
While away from home, you can receive a notification on your mobile device if the alarm system is
triggered.
Required devices
R Mobile device (smartphone or tablet) with an Internet connection
R Wireless router
R Hub (KX-HNB600)
R Any device equipped with a sensor that can trigger the alarm system
– Indoor Camera (KX-HNC200, KX-HNC210)
– Outdoor Camera (KX-HNC600)
– Window/Door Sensor (KX-HNS101)
– Motion Sensor (KX-HNS102)
– Glass Break Sensor (KX-HNS104)
Required procedures
R Hub initial setup and mobile device registration
Refer to the System Setup Guide included with your hub.
R Device registration (if you didn’t purchase the device as part of a pre-configured bundle)
Refer to the Installation Guide included with your device.
R Use the  [Home Network]  app to make sure the desired sensor is enabled for the  [Arm: Away] arm
mode.
See  “Alarm system settings”, Page 46.
R Use the  [Home Network]  app to set the arm mode to  [Arm: Away].
See  “Arming and disarming the alarm system”, Page 45.
While away from home, you can access the system and view live camera images.
Required devices
R Mobile device (smartphone or tablet) with an Internet connection
R Wireless router
R Hub (KX-HNB600)
R A camera
– Indoor Camera (KX-HNC200, KX-HNC210)
– Outdoor Camera (KX-HNC600)
Required procedures
R Hub initial setup and mobile device registration
Refer to the System Setup Guide included with your hub.
R Camera registration (if you didn’t purchase the camera as part of a pre-configured bundle)
Refer to the Installation Guide included with your camera.
R Use the  [Home Network]  app to access the desired camera.
See  “Viewing live camera images”, Page 57.
You can configure the system to record video from a camera if motion is detected.
Required devices
R Mobile device (smartphone or tablet) with an Internet connection
R Wireless router
R Hub (KX-HNB600)
R An SD card (inserted in the hub)
R A camera29
Usage examples 
						

							– Indoor Camera (KX-HNC200, KX-HNC210)
– Outdoor Camera (KX-HNC600)
Required procedures
R Hub initial setup and mobile device registration
Refer to the System Setup Guide included with your hub.
R Camera registration (if you didn’t purchase the camera as part of a pre-configured bundle)
Refer to the Installation Guide included with your camera.
R Use the  [Home Network]  app to configure a smart control scenario. Select a sensor as the trigger and
your camera as the target device.
See  “Creating a scenario that uses a sensor as the trigger”, Page 51.
R If using the camera’s motion detection features as the trigger, use the  [Home Network] app to adjust
the camera’s motion detection features, such as detection sensitivity and detection area, if necessary.
See  “Camera settings”, Page 63.
You can configure the system to turn on a light or other electric device when your mobile device connects
to your wireless router, such as when you return home from outside.
Required devices
R Mobile device (smartphone or tablet) with an Internet connection
R Wireless router
R Hub (KX-HNB600)
R Smart Plug (KX-HNA101)
Required procedures
R Hub initial setup and mobile device registration
Refer to the System Setup Guide included with your hub.
R Smart plug registration (if you didn’t purchase the smart plug as part of a pre-configured bundle)
Refer to the Installation Guide included with your smart plug.
R Use the  [Home Network]  app to configure a smart control scenario. Select  [Trigger when Home
Wi-Fi Connects]  as the trigger and your smart plug as the target device.
See  “Creating a scenario that uses a sensor as the trigger”, Page 51.
You can configure the system to turn on a light or other electric device according to a schedule.
Required devices
R Mobile device (smartphone or tablet) with an Internet connection
R Wireless router
R Hub (KX-HNB600)
R Smart Plug (KX-HNA101)
Required procedures
R Hub initial setup and mobile device registration
Refer to the System Setup Guide included with your hub.
R Smart plug registration (if you didn’t purchase the smart plug as part of a pre-configured bundle)
Refer to the Installation Guide included with your smart plug.
R Use the  [Home Network]  app to configure a smart control scenario that functions on a schedule.
See  “Creating a scenario that uses a schedule as the trigger”, Page 50.
You can configure an indoor camera to notify your mobile device when sound (such as a crying baby) is
detected.
Required devices
R Mobile device (smartphone or tablet) with an Internet connection30
Usage examples