Panasonic Network Function Edition Pt L785u Instruction Manual

11
When [FAILED] has appeared for an item:
If requesting service, ask your nearest Authorised Service Center.
EXHAUST
TEMPERATUREThe air exhaust temperature is too high. The air outlet or
exhaust holes may be blocked.
LAMP REMAIN
TIMEThe lamp runtime has exceeded the prescribed cumulative
time, and it is now time to replace the lamp.
LAMP STATUS Trouble has occurred in the lamp or its drive circuit.
INPUT AIR
TEMP.
SENSORTrouble has occurred in the sensor used to detect the input
air temperature....

12
Using Web Browser Control (continued)
E-mail setup page 
With this projector, if a problem occurs or if the lamp usage time reaches a set
value, an e-mail message can be sent to one or more preset e-mail addresses
(maximum two addresses). Click [Projector Control], then [E-mail set up] to display
the E-mail setup page.
Minimum sending interval
field (applies only to
temperature warnings) E-mail Enable/Disable toggling SMTP server field
Set temperature selection 
(38 °C/100 °F, 40 °C/104 °F, 
42 °C/108...

13
Change lamp usage
time set value
ON/OFF toggling
for permission to
send e-mail based
on lamp usage timePeriodic warning
interval setting (e-mail
is sent on the checked
days of the week/times)
Button to update settings
Destination e-mail address field
The settings for e-mail address 1 are the same.ON/OFF toggling for permission
to send e-mail when error occurs
ON/OFF toggling for
permission to send e-
mail based on air intake
sensor temperature 

14
Using Web Browser Control (continued)
Primary DNS server address
Available input characters:
Numbers (0 - 9), period (.)
(ex. ...)
DNS server setup page
Click [Network Setting], then [DNS Server set up] to display the DNS Server Setup
page.
Button to update settings Secondary DNS server address
Available input characters:
Numbers (0 - 9), period (.)
(ex. ...) 

15
POP server setup page
Click [Network Setting], then [POP server set up] to display the POP Server Setup
page.
Toggling between
Enabling/Disabling
POP before SMTPPOP server name field
Available input characters: 
Alphanumeric characters (A–Z, a–z, 0–9),
hyphen (-), period (.)
Button to update settings  POP server
password field POP server user
name field 

16
Using Web Browser Control (continued)
Adjust clock page
Click [Network Setting], then [Adjust clock] to display the Adjust clock page.
Time zone selection Button to update time
zone setting
Button to update time
and date settings  New date field
New time field
Note:
If the time becomes incorrect immediately after setting the correct time, then the
battery needs to be changed. Contact the dealer where you bought the projector
to have the battery changed. 

17
Network status page 
Click [Network Setting], then [Network status] to display the Network status page.
Network software
version display  Set IP address display Set subnet mask
display  MAC address
display 
Network status display 

18
Using Web Browser Control (continued)
Password change page
This page can be used to change the password entered on page 6. The password
can be changed even through the PC. See page 4 for information on changing the
password through the projector.
Click [Change Password].
Old password input field
New password input field
New password input field
(re-enter for confirmation)
Button for executing
password change Button for erasing all
entered characters 

19 

M0604-0
Professional/Industrial Video
Panasonic Broadcast & Television Systems Company
Division of Matsushita Electric Corporation of America
One Panasonic Way 4E-7 Secaucus, NJ 07094 (201) 392-4443
3330 Cahuenga Blvd West Los Angels, CA 90068 (323) 436-3500
Technical Support:
(800) 524-1448
(800) 526-6610
FAX: (201) 392-6514
E-Mail: [email protected]
© 2004 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.
Printed in Japan