Panasonic Network Camera Wvsf448e Installation Guide

21
Using the optional ceiling mount bracket WV-Q105 (E model only)
When using the optional ceiling mount bracket to mount the camera, first\
 place the installation tem-
plate (WV-Q105 accessory) on the ceiling, and then make a hole in ceiling and mo\
unt the 
WV-Q105.
Next place the installation template label (accessory) on the ceiling,\
 and make a hole to pass the 
cables. After completing this, remove the template label, and mount the camera attachment (acces-
sory) by fixing 4 screws (WV-Q105...

22
IMPORTANT:
	 •	 When	inserting	an	SD	memory	card,	make	sure	the	direction.	
	 •	 Before	 removing	 the	 SD	 memory	 card,	 select	 “Not	 use”	 for	 “SD	 memory	 card”	 on	 the	 [SD	 memory card] tab of the “Basic” page first. Turn off the power after “Not use” selection, and 
then unload the SD memory card. When the SD memory card is inserted or removed with the 
power on, data in the SD memory card may be damaged. 
   (☞ Operating Instructions (included in the CD-ROM))
 
z  Open the SD memory slot...

23
Connection
Before starting the connection, turn off the power of this camera and the devices to be connected. 
Check and prepare the required devices and cables for connection. Note:
	 •	 Since	 the	 connector	 storage	 section	 does	 not	 have a sufficient space, use a LAN cable that do 
not exceed the sizes described in the illustrations.
  
40 mm {1-9/16 inches}Straight section
30 mm {1-3/16 inches}9 mm 
{11/32 inches}
13 mm {1/2 inches}
Example of LAN cable connector
Caution:
	 •	 ONLY	 CONNECT...

24
IMPORTANT:
	•		
Connect/disconnect the audio cables and turn on the power of the camera after turning off the 
power of the audio output devices. Otherwise, loud noise may be heard from the speaker. 
 
xConnecting an external microphone and an external speaker
Connect the audio cable (accessory) to the audio cable connector, then connect the micro-
phone to Microphone/line input connector. 
When disconnecting the audio cable (accessory), pull out the audio cab\
le (accessory) while 
holding down the...

25
v Connecting an External I/O terminal
  Connect the cables of external devices to the 
External I/O terminal plug (accessory). 
  q  When connecting an external device, remove 
8 mm - 9 mm {5/16 inches - 11/32 inches} of 
the outer jacket of the cable and twist the cable 
core to prevent the short circuit first. 
Specification of cable (wire):  
20 AWG - 26 AWG, Single core, twisted
  w  Push down the button of the desired terminal 
on the external I/O terminal plug with a ballpoint 
pen, and release...

26
IMPORTANT:
	 •	 Do	 not	 connect	 2	 wires	 or	 more	 directly	 to	 a	 terminal.	 When	 it	 is	 necessary	 to	 connect	 2	 wires or more, split the wire and connect the split wires to the terminal.
	 •	
Input and output of the External I/O terminal 2 and 3 can be switched by configuring the set-
ting. “Off” is selected by default. It is possible to determine whether or not\
 to receive input 
from External I/O terminal 2 and 3 (ALARM IN2, 3) by selecting “Off”, “Alarm input”, “Alarm 
output”	 or	 “AUX...

27
IMPORTANT:
	 •	 Be	sure	to	use	the	power	cord	plug	provided	with	this	product.	
	 •	 Be	sure	to	fully	insert	the	power	cord	plug	(accessory)	into	the	12	V	DC	power	supply	terminal.	 Otherwise, it may damage the camera or cause malfunction. 
	 •	 When	installing	the	camera,	make	sure	that	excessive	force	is	not	applied	to	the	power	cable.
	 •	 Be	 sure	 to	 use	 an	 AC	 adaptor	 compliant	 with	 the	 Specifications	 regarding	 power	 source	 and	 power consumption. (☞ Page 34) 
 
When using PoE...

28
Installation
Camera mounting
Mount the camera with the camera attachment (accessary)
Installation shall be conducted after turning off each device. 
zDetermine the mounting position and mounting method for the camera.

Secure the camera attachment (accessory) to the two-gang junction box (loc\
ally procured).  
(☞ Pages 19)

Attach the camera attachment (accessory) using the installation templa\
te label (accessory).   
(☞ Page 20)

Attach the camera attachment (accessory) using the optional ceiling...

29
vUsing the camera attachment position marker as a guide, match the “OP\
EN” position of the 
camera to the projection of the camera attachment (accessory).
bEngage the camera attachment fixing screws in the rear of the camera with the camera 
mounting holes of the camera attachment (accessory) and rotate the camera in the direction of 
the arrow shown below to secure the camera. Make sure that the projection of the camera 
attachment will be set to the “LOCK” position. 
(The illustration is an example...

30
nTighten the camera fixing screw.
IMPORTANT:
 •		Securely	 tighten	 the	 camera	 fixing	 screw.	 Failure	 to	 do	 so	 may	 cause	 damage	 or	 the	camera to drop. 
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}) 
 
mAttach the sub cover. (The illustration is an example of using a two-gang junction box.)
Attach the sub cover to the camera, then fix it to the camera with the s\
ub cover fixing 
screws x2. 
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
After that, close the screw covers...