Panasonic Network Camera Wvsf448e Installation Guide

11
About SD memory card
	 •	 Before	removing	the	SD	memory	 card	from	
the  camera,  it  is  necessary  to  select  “Not 
use”  for  “SD  memory  card”  first.  The 
recorded  data  may  be  corrupted  if  the  SD 
memory  card  is  removed  when  “Use”  is 
selected  for  “SD  memory  card”.  Refer  to 
page  22  for  descriptions  of  how  to  insert/
remove an SD memory card. 
	 •	 When	 using	an	SD	 memory	 card,	format	 it	
using  this  product.  Recorded  data  on  the 
SD  memory  card  will  be...

12
Precautions for Installation
Panasonic assumes no responsibility for injuries or property damage resulting from fail-
ures arising out of improper installation or operation inconsistent with this documentation.
This camera is designed to be used indoors. 
This product is not operable outdoors. 
Do not expose this camera to direct sunlight for 
hours and do not install the product near a heater 
or an air conditioner. Otherwise, it may cause 
deformation, discoloration and malfunction. Keep 
this...

13
Screw tightening
	 •	 The	 screws	 and	 bolts	 must	 be	 tightened	with an appropriate tightening torque 
according to the material and strength of 
the installation area. 
	 •	 Do	 not	 use	 an	 impact	 driver.	 Use	 of	 an	 impact driver may damage the screws or 
cause tightening excessively. 
	 •	 Tighten	 screws	at	 a	right	 angle	 to	the	 sur-
face. After tightening screws, perform checks 
to ensure that the tightening is sufficient 
enough so that there is no movement or 
looseness.
Fall...

14
Major operating controls
About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for about 5 seconds or more without releasing this button. Wait about 2 minutes 
after releasing the button. The camera will start up and the settings including\
 the network settings 
will be initialized. Do not turn off the power of the camera during the process of initialization. Before 
initializing the settings, it is...

15

Network connector
12 V DC power 
supply terminal Built-in microphone
External I/O terminals
Audio cable connector
Camera fixing screw
• When the privacy mode is off • When the privacy mode is on

Camera attachment fixing screws
Camera attachment 
fixing screw 

16
Camera attachment (accessory)Direction marker for installation
Camera attachment position marker 

17
Preparations
When installing the camera, there are 4 methods as specified below. 
	 •	 Using	the	two-gang	junction	box	(☞ pages 19)
	 •	 Installing	the	camera	directly	on	the	ceiling	or	wall	(☞ page 20)
	 •	 Using	 the	 optional	 ceiling	 mount	 bracket	 WV-Q105*
1 (for direct mounting on a ceiling)  
(☞ page 21)
IMPORTANT:
	 •	 Procure	 4	 screws	 (M4)	 to	 secure	 the	 camera	 attachment	 (accessory)	 to	 a	 ceiling	 or	 a	 wall	 according to the material of the installation area. In this case, wood...

18
Using the side cable access hole
When installing the camera directly on the ceiling or wall with cables exposed, cut out a portion of 
the enclosure to open a cable access hole.
Side cable access hole
IMPORTANT:
	 •	 To prevent injury and protect cables, smooth opened cable access holes of the enclosure with 
a file or other tool.
Note:
	 • 	 To 	prevent	filings	or	other	substances	entering	inside	the	camera,	remove	the	sub	cover	when	
using a file or other tool to smooth the cable access holes.
  

19
Method of camera installation
Using a two-gang junction box
Secure the camera attachment (accessory) to the two-gang junction box built\
 in a ceiling or wall 
using the fixing screws (locally procured).
TOP
TOP
46 mm {1-13/16 inches}
Direction marker for installation Two-gang junction box
Camera attachment (accessory)
Fixing screws
(4 pcs., locally procured) 83.5 mm {3-9/32 inches}
[Mounting hole pattern]
Note:
	 •	 The direction of “gTOP” on the camera attachment (accessory) determines the upwards...

20
Installing the camera directly on the ceiling or wall
Place the installation template label (accessory) on the ceiling or wa\
ll, and make a hole to pass the 
cable.
Remove the template label, and mount the camera attachment (accessory)\
 by fixing 4 screws 
(locally procured). 
46 mm {1-13/16 inches}Arrow 83.5 mm {3-9/32 inches}
Cable access hole 
(ø30 mm {ø1-3/16 inches})
Installation template label
(accessory)
Fixing screws (4 pcs., locally procured) Camera attachment (accessory)
Direction marker...