Panasonic Network Camera Wv Sw558 Wv Sw559 Installation Guide

							21

Align the direction of the conduit to the direction of female thread for the conduit on the mount 
bracket, and mount the mount bracket to hole A or hole B on the wall or ceiling.
[For use of the hole A]
Note:
  •  Only the same type of holes, A or B, shall be used for mounting.
Conduit
Female thread for conduit Mount bracket
(accessory)
Fixing screws (locally procured)
138 mm
{5-7/16 inches}
85 mm
{3-11/32 inches}
For use of the hole 
85 mm138 mm
{5-7/16 inches}For use of the hole 
{3-11/32 inches} 
						

							22
c  In the direction determined in x, fix the 
camera attachment (accessory) on the 
mount bracket using the fixing screws.
    Recommended tightening torque: 
0.78 N·m {0.58 lbf·ft}
Note:
  •  For wall mounting:
    The camera attachment (accessory) shall be mounted with TOP facing upward. 
  •  For ceiling mounting:
   The camera attachment (accessory) shall be mounted with aligning the front side (the side 
where the Panasonic logo is) of the camera with the position of the arrow in FRONT. 
   
IMPORTANT:
  •  For installations on the wall, to prevent water from accumulating on the surface of the dehu-
midifying device (
☞ page 12), do not connect it at the upper side.
    If water remains inside, the dehumidifying device cannot function properly.
v  Pass the cables through the hole for cable running from the wall or ceiling, and then pass the 
cables between the camera attachment (accessory) and mount bracket to the outside.
Camera 
attachment 
(accessory)
FRONT
TOP
Fixing screws (accessory) 
						

							23
IMPORTANT:
  •  When inserting a SD memory card, make sure the direction.
  •  Before removing the SD memory card, make sure to select “Not use” for “SD memory card” on 
the [SD memory card] tab of the “Basic” page on the setup menu first. (
☞ Operating 
Instructions (included in the CD-ROM))
z  Detach the enclosure. (☞ Page 32)
x  Insert a SD memory card fully into the SD mem-
ory card slot until a click is heard. 
c  Attach the enclosure to the camera. 
 (
☞ Page 38)
v  When removing the SD memory card from the 
SD memory card slot, detach the enclosure 
(
☞ page 32), and push the card until a click is 
heard. After the SD memory card is removed, 
attach the enclosure to the camera again. 
(
☞ Page 38)
Insert/remove a SD memory card (WV-SW559 Only)
Label side 
						

							24
Caution:
  • ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED 
POWER SOURCE (IEC/EN/UL/CSA 60950-1). 
Before starting the connection, turn off the power of this camera and the devices to be connected.
Check and prepare the required devices and cables for connection.
Note:
  •  When using the mount bracket (accessory), it is possible to connect the cables after mounting 
the camera onto the mount bracket. 
  •  Refer to page 19 when connecting the conduit.
Connection
Network cable
RJ-45 (female)
Alarm input/output cable 4P alarm cable (accessory)LAN cable (category 5 or better)
Power cable 
(12 V DC)2P power cable (accessory)
12 V DC (red)
GND (black)
Microphone/line input cable (white)
Audio output cable (black)
SW559
SW559Power cable
12 V DC
Red Positive
Black Negative
z  Connect the microphone/line input cable and the microphone (for use of the audio reception 
function). SW559
Input impedance:  2 kΩ±10 %
Recommended cable length:  Less than 1 m {3.28} (for microphone input)
    Less than 10 m {32.8} (for line input)
Recommended microphone:  Plug-in power type microphone (option)
    Connect a monaural mini plug (ø3.5 mm).
Supply voltage:  2.5 V ±0.5 V
Recommended sensitivity of microphone: −48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
IMPORTANT:
  • Connect/disconnect the external speaker cables or audio/video cables after turning off the 
power of the camera and the amplifier. Otherwise, loud noise may come out from the speaker.  
						

							25
x  Connect an external amplifier-embedded speaker to the audio output cable (for use of the 
audio transmission function). 
SW559
    Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.). 
  •  Recommended cable length: Less than 10 m {32.8 ft}
c  Connect the alarm input/output cable.
  
Terminal name Ratings
ALARM OUT, AUX OUT Open collector output (maximum applied voltage: 20 V DC)
Open 4 V DC - 5 V DC by internal pull-up
Close Output voltage 1 V DC or less (50 mA or less)
ALARM IN, DAY/NIGHT IN Non-voltage make contact input (4 V DC - 5 V DC, internally pulled 
up)
Off Open or 4 V DC - 5 V DC
On Make contact with GND (required drive current: 1 mA or more)
Note:
  •  Check if rating of an external device such as a sensor is applicable to the rating of this product 
by referring to the provided operating instructions.
6SHFL
„FDWLRQRI3DODUPFDEOHDFFHVVRU\
*1EODFN
$/$50,1$8;287JUD\7HUPLQDO
$/$50,1$/$50287UHG7HUPLQDO
$/$50,1$
						

							26
IMPORTANT:
  •  Input and output of the EXT I/O terminal 2 and 3 can be switched by configuring the setting. 
Off is selected by default. It is possible to determine whether or not to receive input from EXT 
I/O terminal 2 and 3 (ALARM IN2, 3) by selecting Off, Alarm input, Alarm output or AUX 
output for Terminal 2 or Terminal 3 on the [Alarm] tab on the Alarm page. Refer to the 
Operating Instructions  (included in the CD-ROM) for further information. 
  •  When using the EXT I/O terminals as the output terminals, ensure they do not cause signal col-
lision with external signals.
  •  In order for the EXT I/O terminal to detect alarm inputs when the terminal status is changed 
from Open to Close (On) or from Close to Open (Off), about 100 ms or more is needed.
   Because alarms cannot be detected for about 5 seconds after a detection is made, alarm 
inputs received within about 5 seconds after an alarm is detected are not detected.
v  Connect a LAN cable (category 5 or better, straight, STP*) to the network connector.
    * For Europe
b  Connect the power cable. 
  •  When using 12 V DC power supply*
1
    Connect the output cable of the AC adaptor to the 2P power cable.
  •  When using PoE (IEEE802.3af compliant)
    Connect a LAN cable (category 5 or better, straight, STP*
2) between a PoE device (such as a 
hub) and the network connector of the camera. 
  *1  ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED 
POWER SOURCE (IEC/EN/UL/CSA 60950-1).
 *2 For Europe
IMPORTANT: 
  •  Use all 4 pairs (8 pins) of the LAN cable. 
  •  The maximum cable length is 100 m {328 feet}.
  •  Make sure that the PoE device in use is compliant with IEEE802.3af standard. 
  • When connecting both the 12 V DC power supply and the PoE device for power supply, 
12 V DC will be used for power supply. Depending on the PoE device used, the power supply 
lamp may not light and the network connections may not be possible. In this case, disable the 
PoE device setting, and refer to the operating instructions of the PoE device in use.
  •  When the LAN cable is disconnected once, reconnect the cable after about 2 seconds. When 
the cable is quickly reconnected, the power may not be supplied from the PoE device. 
						

							27
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera with cables 
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are not 
waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to apply 
waterproof treatment in the following procedure. Failure to observe this or use of a tape other than 
the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting in malfunc-
tion.
LAN cable
Alarm input/output cable, power cable, microphone/line input cable*, audio output 
cable*
* 
SW559
IMPORTANT: 
  •  Waterproof treatment is also to be applied to the 2P power cable (accessory), the 4P alarm 
cable (accessory) and other connection cables if they are subject to rain.
Note:
  How to wind the supplied waterproof tape
  •  Stretch the tape by approx. twice (see the illustration) 
and wind it around the cable. Insufficient tape stretch 
causes insufficient waterproofing.
  •  Make sure to wind the tape so that it does not press 
down on the hook of the network cable.
  •  To install this product outdoors, be sure to waterproof the cables. 
Waterproof grade (IEC IP66 or equivalent) is applied to this product 
only when it is installed correctly as described in these operating 
instructions and appropriate waterproof treatment is applied. The 
mount brackets are not waterproofed.
   
Wind the tape in a 
half-overlapping manner. 
Wind the tape in a 
half-overlapping manner. 
Stretch the tape to 
about twice.
2x
hook 
						

							28
Connection example when connecting to a network using a 
PoE hub 
Powered speaker 
(option)
Powered speaker 
(option)Microphone 
(option)
Microphone 
(option)Video monitor 
(for adjustment use only)
Video monitor 
(for adjustment use only)PoE device (hub)
LAN cable 
(category 5 or better, 
straight, STP*)
LAN cable 
(category 5 or better, straight, STP*)LAN cable 
(category 5 or better, 
straight, STP*)
PCSW559
SW559
SW559
SW559

LAN cable (category 5 or better, straight, STP*)
* For Europe
IMPORTANT: 
  •  The video monitor is used for checking the adjustment of the angular field of view when install-
ing the camera or when servicing. It is not provided for recording/monitoring use.
  •  Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
  •  Power supply is required for each network camera. When using a PoE device (hub), 12 V DC 
power supply is unnecessary.  
						

							29
z  Mount the camera.
    
 q  Connect each cable. (
☞ Page 24) Waterproof the connecting portion. (☞ Page 27)
 w  Align the OPEN on the camera with the projection of the camera attachment (accessory).
 e  Engage the camera attachment fixing screws on the rear of the camera in the camera 
mounting holes of the camera attachment (accessory) and rotate the camera in the arrow 
direction to secure the camera attachment (accessory) and camera. 
    Rotate the camera until a click is heard so that the projection of the camera attachment 
(accessory) will be set to the LOCK position.
   
Installation
&DPHUDDWWDFKPHQW
„[LQJVFUHZ Projection Camera mounting hole
OPENLOCK 
						

							30

 q  Attach the camera onto the camera attachment (accessory) while aligning the OPEN mark of 
the camera with the projection of the camera attachment (accessory). 
IMPORTANT: 
  •  When mounting the camera body, cables shall 
be run between the camera attachment (acces-
sory) and mount bracket as indicated by the 
arrows in the illustration.
  *  Cable running as indicated by the arrows in the 
illustration is an example. Cable running shall be 
varied with installation environment. 
   
LOCKOPEN
LOCKOPEN
Projection