Panasonic Network Camera Wv Sw558 Wv Sw559 Installation Guide

31
 w  Engage the camera attachment fixing screws of 
the camera with the screw hole of the camera 
attachment (accessory) and rotate the camera 
in the direction of the arrow to secure the cam-
era to the camera attachment (accessory).
    Rotate the camera until a click is heard so that 
the projection of the camera attachment (acces-
sory) will be set to the LOCK position.
 e  Connect the cables on the side of the mount 
bracket. (
☞ Page 24)
   Waterproof the connecting portion. (
☞ Page 
27)...

32
 t Attach the base cover (accessory) that was 
removed according the steps in page 19.
 y  Use the bit for tamperproof screw (accessory) 
to tighten the fixing screws provided on both 
sides of the base cover (accessory). 
(Recommended tightening torque: 
0.78 N·m {0.58 lbf·ft})
x  Detach the enclosure from the main 
body by loosening the three fixing 
screws. 
    Loosen the three fixing screws by using the bit 
for tamperproof screw (accessory). 
  
IMPORTANT: 
  •  Do not hold the inner dome when...

33
&DPHUD

34
z  Adjust the camera angle.
When determining the camera angle, repeat fine adjustments by gradually moving the panning 
table, tilting table, and azimuth adjustment ring. 
Horizontal position (Panning)
Loosen the panning lock screw, rotate the panning table to adjust the pan direction. (Adjustable 
range: 340 °)
Panning is possible within the range of 180 ° (when panning clockwise) and 160 ° (when panning 
counterclockwise). 
After adjustment, tighten the panning lock screw to fix the panning table....

35
    
Horizontal: 24.20° (TELE) to 86.60° (WIDE)
    After adjustment, tighten the tilting lock screws (x2) to fix the tilting table. 
    (Recommended tightening torque: 0.59 N·m {0.44 lbf·ft})
Note:
  •  When the tilting table is turned to the edge of the adjustable range (±75°), it must be noted that 
the shadow of the enclosure may be projected.
  •  When the camera is installed to a wall, the image is reversed in the default settings. To correct 
the way the image is displayed, rotate the panning...

36
x  Adjust the angular field of view and the focus. 
    Adjust the angular field of view in accordance with the distance between the camera lens and a 
photographic subject. These adjustments shall be performed together with the camera angle 
adjustment.
 q  Loosen the zoom lock knob and move the knob between TELE and WIDE to obtain the appro-
priate angle of view. 
 w  Press the auto focus (AF) button twice quickly to perform basic adjustments. The lamp blinks 
during auto focus (AF) adjusting. When...

37
IMPORTANT: 
  •  Do not move the focus ring.
  •  Defocus may be caused by the reinstalled enclosure. In this case, perform the auto focus func-
tion from the setup menu. 
  •  After performing basic adjustments, make sure to press the auto focus (AF) button once to per-
form detailed adjustments.
Note:
  •  If the zoom lock knob is fully turned in the W direction, the periphery may become dark. In 
such a case, turn the zoom lock knob in the T direction for readjustment.
  •  If the zoom lock knob is...

38
c  Attach the enclosure to the camera.
    Attach the cutout part of the main unit to the grooved part of the enclosure.
IMPORTANT: 
  •  Securely tighten all the fixing screws (x3) of enclosure. Otherwise, water exposure may cause 
damage or malfunction of camera, or camera dropping may result in injury. 
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
  •  Remove the protection sheet from the outside of the dome. 
Groove for 
mounting
Cutout for 
mounting 

39
Configure the network settings
Configuring the camera so that it can be accessed from a PC
The following are descriptions for when the camera with default settings is configured. If you 
are using firewall software on your PC, the Setup Program may not be able to find any 
cameras on your network. Configure the setting of the camera after temporarily invalidating 
the firewall software. Contact the network administrator or your Internet service provider for 
information about configuring the settings...

40
c  Select the camera you want to configure, and click [Access Camera].
Note: 
 • When cameras are displayed in [Panasonic IP Setting] screen, click the camera with same 
MAC address as the MAC address printed on the camera that you want to configure.
v  If the installation screen of the viewer software “Network Camera View 4S” is displayed, follow 
the instructions of the wizard to start the installation. (The viewer software is installed from the 
camera.)
  •  The “Live” page will be displayed.
  •...