Panasonic Network Camera Wv Sw558 Wv Sw559 Installation Guide

21

Align the direction of the conduit to the direction of female thread for the conduit on the mount 
bracket, and mount the mount bracket to hole A or hole B on the wall or ceiling.
[For use of the hole A]
Note:
  •  Only the same type of holes, A or B, shall be used for mounting.
Conduit
Female thread for conduit Mount bracket
(accessory)
Fixing screws (locally procured)
138 mm
{5-7/16 inches}
85 mm
{3-11/32 inches}
For use of the hole 
85 mm138 mm
{5-7/16 inches}For use of the hole 
{3-11/32 inches} 

22
c  In the direction determined in x, fix the 
camera attachment (accessory) on the 
mount bracket using the fixing screws.
    Recommended tightening torque: 
0.78 N·m {0.58 lbf·ft}
Note:
  •  For wall mounting:
    The camera attachment (accessory) shall be mounted with TOP facing upward. 
  •  For ceiling mounting:
   The camera attachment (accessory) shall be mounted with aligning the front side (the side 
where the Panasonic logo is) of the camera with the position of the arrow in FRONT....

23
IMPORTANT:
  •  When inserting a SD memory card, make sure the direction.
  •  Before removing the SD memory card, make sure to select “Not use” for “SD memory card” on 
the [SD memory card] tab of the “Basic” page on the setup menu first. (
☞ Operating 
Instructions (included in the CD-ROM))
z  Detach the enclosure. (☞ Page 32)
x  Insert a SD memory card fully into the SD mem-
ory card slot until a click is heard. 
c  Attach the enclosure to the camera. 
 (
☞ Page 38)
v  When removing the SD memory...

24
Caution:
  • ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED 
POWER SOURCE (IEC/EN/UL/CSA 60950-1). 
Before starting the connection, turn off the power of this camera and the devices to be connected.
Check and prepare the required devices and cables for connection.
Note:
  •  When using the mount bracket (accessory), it is possible to connect the cables after mounting 
the camera onto the mount bracket. 
  •  Refer to page 19 when connecting the conduit.
Connection
Network...

25
x  Connect an external amplifier-embedded speaker to the audio output cable (for use of the 
audio transmission function). 
SW559
    Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.). 
  •  Recommended cable length: Less than 10 m {32.8 ft}
c  Connect the alarm input/output cable.
  
Terminal name Ratings
ALARM OUT, AUX OUT Open collector output (maximum applied voltage: 20 V DC)
Open 4 V DC - 5 V DC by internal pull-up
Close Output voltage 1 V DC or less (50 mA or less)
ALARM IN,...

26
IMPORTANT:
  •  Input and output of the EXT I/O terminal 2 and 3 can be switched by configuring the setting. 
Off is selected by default. It is possible to determine whether or not to receive input from EXT 
I/O terminal 2 and 3 (ALARM IN2, 3) by selecting Off, Alarm input, Alarm output or AUX 
output for Terminal 2 or Terminal 3 on the [Alarm] tab on the Alarm page. Refer to the 
Operating Instructions  (included in the CD-ROM) for further information. 
  •  When using the EXT I/O terminals as the...

27
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera with cables 
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are not 
waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to apply 
waterproof treatment in the following procedure. Failure to observe this or use of a tape other than 
the provided waterproof tape (such as a vinyl...

28
Connection example when connecting to a network using a 
PoE hub 
Powered speaker 
(option)
Powered speaker 
(option)Microphone 
(option)
Microphone 
(option)Video monitor 
(for adjustment use only)
Video monitor 
(for adjustment use only)PoE device (hub)
LAN cable 
(category 5 or better, 
straight, STP*)
LAN cable 
(category 5 or better, straight, STP*)LAN cable 
(category 5 or better, 
straight, STP*)
PCSW559
SW559
SW559
SW559

LAN cable (category 5 or better, straight, STP*)
* For Europe
IMPORTANT:...

29
z  Mount the camera.
    
 q  Connect each cable. (
☞ Page 24) Waterproof the connecting portion. (☞ Page 27)
 w  Align the OPEN on the camera with the projection of the camera attachment (accessory).
 e  Engage the camera attachment fixing screws on the rear of the camera in the camera 
mounting holes of the camera attachment (accessory) and rotate the camera in the arrow 
direction to secure the camera attachment (accessory) and camera. 
    Rotate the camera until a click is heard so that the...

30

 q  Attach the camera onto the camera attachment (accessory) while aligning the OPEN mark of 
the camera with the projection of the camera attachment (accessory). 
IMPORTANT: 
  •  When mounting the camera body, cables shall 
be run between the camera attachment (acces-
sory) and mount bracket as indicated by the 
arrows in the illustration.
  *  Cable running as indicated by the arrows in the 
illustration is an example. Cable running shall be 
varied with installation environment. 
   
LOCKOPEN...