Panasonic Network Camera Wv Sw396a Installation Guide

Step 5
Attach the front and rear sunshields (accessory) to the 
camera.
  q  Put the fingers on the dents of the front and rear sun-
shields to detach the hooks. The sunshields will be 
divided into two parts. 
   For loss prevention, one side of the front and rear 
sunshields are linked together with a wire. 
  w  Locate the front and rear sunshields to the position 
that covers the housing base. 
  e  Joint both sides of front and rear sunshields. 
   Joint the hook and dent on the linked side, and...

Connection
Caution:
Before starting connection, make sure that the circuit breaker is switched off. Failure to observe this may cause fire, 
electric shock, injury, or damage to the product. 
    
Coaxial cableTo  the monitor used 
for adjustment
8P alarm cable (accessory) To a sensor
To  a plug-in power type microphone
To  an external powered speaker To
 a PoE+ hub, PC, etc.
Output cable for the 
monitor used for 
adjustment
External I/O cable
Microphone input cable (white)Audio output cable (black) LAN...

• 24 V AC power supply connector kit (accessory)
Recommended specification of cable (wire)
Wire size (AWG), 
stranded  wire #24
(0.22 mm) #22
(0.33 mm) #20
(0.52 mm) #18
(0.83 mm)
Length of  cable 20 m  
{65.62 feet} 30 m  
{98.43 feet} 45 m  
{147.64 feet} 75 m 
{246.06 feet}
Terminals of the power supply connector
Pin No. Signal
1
2
3
4 24 V AC LIVE
24 V AC NEUTRAL
Ground
Not use
• How to assemble the power supply connector
Remove approx. 3 mm {1/8  inches} of the outer jacket of 
the cable and twist...

	 •	 ALARM	 IN1/	 DAY/NIGHT	 IN,	 ALARM	 IN2,	 ALARM	IN3
Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF: Open or 4 V - 5 V DC
ON: Make contact with GND (required drive current:  1 mA or more)
	 •	 ALARM	OUT,	AUX	OUT Output specification: Open collector output (maxi-mum applied voltage: 20 V DC)
Open: 4 V - 5 V DC by internal pull-up
Close: Output voltage 1 V DC or less (maximum drive  current: 50 mA)
• Microphone/line input cable
Connect a monaural mini plug...

Connection example 
(Refer to page 22 for how to connect the cables.) 
When connecting with a PC directly

LAN cable (category 5e or better, cross, STP*)
* E model only
    
To the power supply 
(24 V AC)
LAN cable 
(category 5e or better, cross, STP*)
PCPowered speaker (option)
Plug-in power type 
microphone (option)
RJ-45 female connector (cable integrated type) 
Recommended total extended 
cable length: 1 m {3.28 feet}
25 

When connecting to a network using a PoE+ hub

LAN cable (category 5e or better, straight, STP*)
* E model onlyImportant:
	 •	 The	video	monitor	is	used	for	checking	the	adjustment	of	the	angular	field	of	view	when	installing	the	camera	or	when	 servicing. It is not provided for recording/monitoring use.
	 •	 Depending	on	the	monitor,	some	characters	(camera	title,	preset	ID,	etc.)	may	not	be	displayed	on	the	screen.	
	 •	 Use	a	switching	hub	or	a	router	which	is	compliant	with	10BASE-T/100BASE-TX	or...

Initialize the camera
Use the initial set switch to reset the settings of the camera to the default. Important:
	 •	 The	 settings	 including	 the	 network	 settings	 will	 be	 initialized.	 Note	 that	 the	 preset	 position	 settings	 and	 the	 CRT	 key	 (SSL encryption key) used for the HTTPS protocol will not be initialized.
    
Step 1
Open the SDHC/SD memory card slot cover by following 
steps 1 - 3 of the "How to insert an SDHC/SD memory 
card" section (☞ page 15). 
Step 2
Move the initial...

Using the CD-ROM
About the CD launcher
Insert the provided CD-ROM into the CD-ROM drive of your PC to display the CD launche\
r window.
	 •	 If	the	launcher	window	is	not	displayed,	double	click	the	"CDLauncher.exe"	file	on	the	CD-ROM.
	 •	 The	 License	 Agreement	 will	 be	 displayed.	 Read	 the	 Agreement	 and	 choose	 "I	 accept	 the	 term	 in	 the	 license	 agree-ment",	and	click	[OK].
Using	the	supplied	CD-ROM,	the	following	actions	can	be	performed.
 q	 The	Panasonic	IP	setting...

Installing Panasonic IP setting software
On	the	CD	launcher	window,	click	the	[Install]	button	next	to	[IP	Setting	Software]	to	display	the	Panasonic	IP	setting	soft-ware	installation	window.	Confirm	the	following	settings	before	starting	the	installation.
 q Select	the	Panasonic	IP	setting	software	to	install.
 w Select	where	to	create	the	Panasonic	IP	setting	shortcut	icon	when	the	Panasonic	IP	setting	software	is	installed.
 e Specify	which	folder	on	the	PC	to	install	the	Panasonic	IP	setting	software...

Installing the Viewer software
The	Viewer	software	(Network	Camera	View4S)	must	be	installed	on	the	PC	in	order	to	display	camera	images.	On	the	CD	launcher	window,	click	the	[Install]	button	next	to	[Viewer	Software],	and	follow	the	instructions	displayed	on	the	window	to	install	 the	 software.	 A	 message	 is	 displayed	 if	 a	 PC	 that	 does	 not	 have	 the	 Viewer	 software	 installed	 tries	 to	 access	 the	camera.	 Install	 the	 software	 by	 following	 the	 instructions	 displayed	 on	 the...