Panasonic Network Camera Wv Sp102 Wv 105 Installation Guide

21
Remove the angle adjustment cover
After  determining  the  installation  angle  of  the  camera,  remove  the  angle  adjustment  cover.  Make 
sure  the  camera  is  secured  to  the  camera  mount  bracket,  and  place  the  sticker  (accessory)  over 
the tripod screw hole on which the hook of the angle adjustment cover was put.
Secure the safety wire on the ceiling or wall
Secure  the  safety  wire  to  the  foundation  part  of  the  construction  or  a  part  with  adequate  strength 
(minimum...

22

Sticker 
(accessory)
Safety wire lug 
(locally procured)
Foundation part of construction 
or part with adequate strength
Safety wire 
(locally procured)
Safety wire 
(locally procured)
Recommended screw M6 
Minimum pull-out strength 
196 N {44.06 lbf}

Safety wire 
(accessory)
Sticker 
(accessory)


    
Washer (accessory)
Ceiling
Spring washer (accessory)
Recommended screw M4 
Minimum pull-out strength 
196 N {44.06 lbf}
Safety wire (accessory) 

23
Before starting the connection, turn off the power of this camera and the devices to be connected.
Check and prepare the required devices and cables for connection.
Connection
12V  ININITIAL
SET
ACT
LINK POWER
10BASE-T/
100BASE-TX
LAN cable
(This illustration 
represents WV-SP105.)
12V  IN
INITIAL
SET
ACT
LINK POWER
10BASE-T/
100BASE-TX
(This illustration 
represents WV-SP105.)
To 12 V DC 
power supply
(12 V DC)
(GND)12 V DC power 
cord plug 
(accessory)
z  Connect a LAN cable (category 5 or better,...

24
Important:
	 •	 Be	sure	to	use	the	power	cord	plug	(accessory)	provided	with	this	product.
	 •	 Be	 sure	to	fully	 insert	 the	power	 cord	plug	(accessory)	 into	the	12	V	DC	 power	 supply	 terminal.	
Otherwise, it may damage the camera or cause malfunction.
	 •	 Mount	the	camera	so	that	excessive	force	is	not	applied	to	the	power	cord.
	 •	 Be	 sure	to	use	 an	AC	 adaptor	 compliant	 with	the	Specifications	 regarding	power	source	 and	
power consumption (
☞ p.29).
 
●
 When using PoE (IEEE802.3af...

25
Connection example when connecting to a network using a 
PoE hub

LAN	cable	(category	5	or	better,	straight,	STP*)
*	PAL	models	onlyImportant:
	 •	 The	 camera	is	to	 be	 connected	 only	to	PoE	 networks	 without	routing	to	the	 outside	 plant	when	
using PoE.
	 •	 Use	a	switching	hub	or	a	router	which	is	compliant	with	10BASE-T/100BASE-TX.
	 •	 Power	 supply	is	required	 for	each	 network	 camera.	 When	using	a	PoE	 device	 (hub),	12	V	DC	
power supply is unnecessary.
 
PCLAN cable 
(category 5 or...

26
Configure the network settings
Install the software
Before installing the software, refer to the readme file on the provided CD-ROM first.
Software included on the provided CD-ROM
	 •		Panasonic	IP	setting	software
    Configure the network settings of the camera. Refer to the following for further\
 information.
	 •	 	Viewer	Software	"Network	Camera	View	4S"
    It is necessary to install the viewer software "Network Camera View 4S" to display images on a 
PC. Install the viewer...

27
z Start the Panasonic IP setting software.
x Click  the  [IP  setting]  button  after  selecting  the 
MAC  address/IP  address  of  the  camera  to  be 
configured.
Note:
	 •	 When	 using	a	DHCP	 server,	 the	IP	address	
assigned  to  the  camera  can  be  displayed  by 
clicking  the  [Refresh]  button  of  the  IP  setting 
software.
	 •	 When	 a	duplicate	 IP	address	 is	used,	 the	corre-
sponding  MAC  address/IP  address  will  be  dis-
played shaded.
 
c  Complete  each  network  setup  item...

28
Troubleshooting
Before asking for repairs, check the symptoms with the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the 
table or a problem is not described below.
SymptomCause/solutionReference 
pages
Power is not turned on. When using DC power supply
	 •	 Is	12	V	DC	power	supply	connect	to	the	
power supply terminal? 
→  Check whether the connection is appropri-
ately established.
	 •	 Is	the	AC	adaptor	in	use	compliant	with	the...

29
Specifications
● Basic
Power source: 12 V DC, PoE (IEEE802.3af compliant)
Power consumption:  WV-SP105
	 	 	 12	V	DC*:	200	mA,
     PoE: 2.8 W (Class 2 device)
    WV-SP102
	 	 	 12	V	DC*:	140	mA,
     PoE: 2.0 W (Class 2 device)
	 	 *		FOR	UL	LISTED	MODEL(S),	ONLY	CONNECT	12	V	DC	
CLASS 2 POWER SUPPLY. 
Ambient operating temperature:  0 °C to +40 °C {32 F° to 104 F°}
Ambient operating humidity:  Less than 90 % (no condensation)
Dimensions:  55 mm (W) x 55 mm (H) x 122 mm (D)  
{2-5/32 inches (W) x...

30
Gain (AGC): On(Low)/ On(Mid)/ On(High)/ Off
Adaptive black stretch:  On/Off
Light control mode setting:  Indoor scene (50 Hz/60 Hz)/ ELC
Maximum exposure time:  WV-SP105: 
       1/30 s, 3/100 s, 3/120 s, 2/100 s, 2/120 s, 1/100 s, 
1/120 s, 1/250 s, 1/500 s, 1/1000 s, 1/2000 s, 1/4000 s, 
1/10000 s
    WV-SP102: 
       1/30 s, 3/100 s, 3/120 s, 2/100 s, 2/120 s, 1/100 s, 
1/120 s, 1/250 s, 1/500 s, 1/1000 s, 1/2000 s, 1/4000 s, 
1/8000 s
Auto slow shutter:  WV-SP105: 
     Off(1/30 s), max. 2/30 s,...