Panasonic Network Camera Wv Sp102 Wv 105 Installation Guide

11
Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a 
fall  of  this  product  resulting  in  injury  or  acci-
dents.
Consult the dealer for the inspections.
Do not use this product in an inflammable 
atmosphere.
Failure to observe this may cause an explosion 
resulting in injury.
Avoid installing this product in the loca-
tions where salt damage occurs or corro-
sive gas is produced.
Otherwise,  the  mounting  portions  will  deterio-
rate and accidents such as a...

12
Cleaning this product body
Be sure to turn off the power before cleaning.
Do  not  use  strong  abrasive  detergent  when 
cleaning  this  product.  Otherwise,  it  may  cause 
discoloration.
When using a chemical cloth for cleaning, read 
the  caution  provided  with  the  chemical  cloth 
product.
When the dirt is hard to remove, use a 
mild detergent and wipe gently.
When  the  dirt  is  hard  to  remove,  use  a  mild 
detergent  and  wipe  gently.  Then,  wipe  off  the 
remaining detergent with...

13
Precautions for Installation
No responsibility will be taken by our com-
pany with respect to consequeces result-
ing from the use, damage or both of the 
camera.
This product is designed to be used 
indoors.
The product is not operable outdoors.
Do not expose the product to direct sunlight for 
hours  and  do  not  install  the  product  near  a 
heater  or  an  air  conditioner.  Otherwise,  it  may 
cause  deformation,  discoloration  and  malfunc-
tion.  Keep  the  product  away  from  water  and...

14
Angle adjustment
Be  sure  to  loosen  the  screw  of  the  camera 
mount  bracket  when  the  camera  angle  is 
adjusted. If the camera angle is changed when 
the  screw  is  tight,  excessive  force  is  applied  to 
the  camera  mount  bracket  and  this  product, 
and  accordingly  they  may  be  damaged.  Be 
sure  to  tighten  the  fixing  piece  securely  after 
camera angle adjustment.
Radio disturbance
When this product is used near TV/radio anten-
na, strong electric field or magnetic field...

15
Major operating controls
About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for around 5 seconds or more without releasing this button. Wait around 2 minutes 
after  releasing  the  button.  The  camera  will  start  up  and  the  settings  including  the  network  settings 
will  be  initialized.  Before  initializing  the  settings,  it  is  recommended  to  write  down  the  settings  in 
advance.
12V...

16
Installation
Connect the safety wire
If  an  installation  area  has  sufficient  strength  (☞  page  17),  secure  the  provided  safety  wire  to  the 
installation area.
If not, procure another wire that can substitute for the safety wire (accessory).
The following is an example of safety wire connection.
Important:
	 •	 Be	sure	to	install	the	safety	wire.	Ask	your	dealer	for	installation.
	 •	 Take	 care	so	that	 the	camera	 does	not	roll	over.	 Do	not	 remove	 the	camera	 cover	film	until	 the...

17
If  the  screw  of  camera  mount  bracket  is  too  long,  adjust  the  screw  length  using  a  spacer  so  as  to 
meet the dimensions and conditions described in the illustration.Important:
	 •	 When	 the	camera	 mount	bracket	 (locally	pro-
cured)  is  mounted  on  a  wall,  be  sure  to 
observe  the  mounting  height  described  on 
the illustration.
 
    
Camera mounting
The camera will be mounted on the camera mount bracket (locally procured). After the angular field 
of view is determined,...

18
Attach the angle adjustment cover to the camera
Important:
	 •	 Angle	 adjustment	 cover	(accessory)	 is	intended	 for	the	 tentative	 adjustment	 of	angular	 field	of	
view. Perform the final adjustment while viewing the images actually on a mo\
nitor.
	 •	 The	angle	adjustment	cover	is	dedicated	to	this	product.	
 
z  Build up the angle adjustment cover (accessory).
Protrusions
Slots
Opening sections
Opening sections
Target sections
Target sectionsHook
 
q  Insert the protrusions into the slots....

19
Remove the camera cover film.
Make sure that the hook is situated at the bot-
tom,  and  place  the  angle  adjustment  cover 
over the camera.
    Fold  the  hook  inward,  and  put  the 
hook  on  the  tripod  screw  hold  for  fixa-
tion.
    
Camera cover lm
Camera cover lm
Remove the camera cover film.
Make  sure  that  the  hook  is  situated  at  the  top, 
and  place  the  angle  adjustment  cover  over  the 
camera.
    
Fold  the  hook  inward,  and  put  the 
hook  on  the  tripod  screw...

20
How to check the angular field of view
z Check the shooting range with the angle adjustment cover attached to the\
 camera.
x You can see the camera adjustment cover as illustrated when you look toward the camera from 
a desired shooting area.
    
Seen from Position A Seen from Position B
C
A Cross line 
disappears.
Cross line can be seen properly. Cross line overlaps an opening 
section frame.
(Shooting range)
Opening 
section frame
Opening 
section frame
B
* The angular field of view can be checked...