Panasonic Network Camera Wv Sp102 Wv 105 Installation Guide

							21
Remove the angle adjustment cover
After  determining  the  installation  angle  of  the  camera,  remove  the  angle  adjustment  cover.  Make 
sure  the  camera  is  secured  to  the  camera  mount  bracket,  and  place  the  sticker  (accessory)  over 
the tripod screw hole on which the hook of the angle adjustment cover was put.
Secure the safety wire on the ceiling or wall
Secure  the  safety  wire  to  the  foundation  part  of  the  construction  or  a  part  with  adequate  strength 
(minimum pull-out strength 196 N {44.06 lbf}).
Prepare the fixing screw according to the material of the area where the safety wire is to be fixed.
For  mounting  on  ceiling,  use  the  safety  wire  (accessory),  washer  (accessory)  and  spring  washer 
(accessory). For mounting on wall, use a safety wire kit (locally procured).Important:
	 •	 The	safety	wire	shall	be	adjusted	to	remove	slack.
	 •	 Be	 sure	to	install	 the	safety	 wire	to	prevent	 a	fall	 of	the	 camera	 resulting	 in	injury	 or	accidents	 in	
case the camera comes off.
	 •	 To	 prevent	 the	mounting	 strength	from	becoming	 lower,	do	not	 use	 wooden	 screws	to	secure	
the safety wire.
 
     
						

							22

Sticker 
(accessory)
Safety wire lug 
(locally procured)
Foundation part of construction 
or part with adequate strength
Safety wire 
(locally procured)
Safety wire 
(locally procured)
Recommended screw M6 
Minimum pull-out strength 
196 N {44.06 lbf}

Safety wire 
(accessory)
Sticker 
(accessory)


    
Washer (accessory)
Ceiling
Spring washer (accessory)
Recommended screw M4 
Minimum pull-out strength 
196 N {44.06 lbf}
Safety wire (accessory) 
						

							23
Before starting the connection, turn off the power of this camera and the devices to be connected.
Check and prepare the required devices and cables for connection.
Connection
12V  ININITIAL
SET
ACT
LINK POWER
10BASE-T/
100BASE-TX
LAN cable
(This illustration 
represents WV-SP105.)
12V  IN
INITIAL
SET
ACT
LINK POWER
10BASE-T/
100BASE-TX
(This illustration 
represents WV-SP105.)
To 12 V DC 
power supply
(12 V DC)
(GND)12 V DC power 
cord plug 
(accessory)
z  Connect a LAN cable (category 5 or better, straight, 
STP*)	 to	the	 network	 connector	 on	the	 rear	 of	the	
camera.
	 *	PAL	models	only
    
x  Connect the power cord.
Important:
	 •	 The	12	V	DC	power	supply	shall	be	insulated	from	the	commercial	AC	power.
 
●
 When using 12 V DC power supply*
  q  Loosen the screw of the power cord plug (accessory).
  w	 Connect	 the	cable	 of	the	 12	V	DC	 power	 supply*	 to	the	
power cord plug.
    Strip  3  mm  -  7  mm  {1/8"  to  9/32"}  from  the  end  of  the 
wire,  and  twist  the  stripped  part  of  the  wire  sufficiently  to 
avoid short circuit.
Specification  of  cable  (wire):  16  AWG  -  28  AWG, 
Single core, twisted
	 •	 Check	 whether	the	stripped	 part	of	the	 wire	 is	not	
exposed and is securely connected.
  e  Tighten the screw of the power cord plug (accessory).
  r  Connect the power cord plug (accessory) to the 12 V DC 
power supply terminal on the rear of the camera.
	 *	 FOR	 UL	LISED	 MODEL(S),	 ONLY	CONNECT	 12	V	DC	
CLASS 2 POWER SUPPLY. 
     Caution:
	 •	 FOR	UL	LISTED	MODEL(S),	ONLY	CONNECT	12	V	DC	CLASS	2	POWER	SUPPLY. 
						

							24
Important:
	 •	 Be	sure	to	use	the	power	cord	plug	(accessory)	provided	with	this	product.
	 •	 Be	 sure	to	fully	 insert	 the	power	 cord	plug	(accessory)	 into	the	12	V	DC	 power	 supply	 terminal.	
Otherwise, it may damage the camera or cause malfunction.
	 •	 Mount	the	camera	so	that	excessive	force	is	not	applied	to	the	power	cord.
	 •	 Be	 sure	to	use	 an	AC	 adaptor	 compliant	 with	the	Specifications	 regarding	power	source	 and	
power consumption (
☞ p.29).
 
●
 When using PoE (IEEE802.3af compliant)
Connect	 a	LAN	 cable	 (category	 5	or	 better,	 straight,	 STP*)	between	 a	PoE	 device	 (such	as	a	hub)	
and the network connector of the camera.
*	PAL	models	only
Important:
	 •	 Use	all	4	pairs	(8	pins)	of	the	LAN	cable.
	 •	 The	maximum	cable	length	is	100	m	{328'}.
	 •	 Make	sure	that	the	PoE	device	in	use	is	compliant	with	IEEE802.3af	standard.
	 •	 When	 connecting	 both	the	12	V	DC	 power	 supply	 and	the	PoE	 device	 for	power	 supply,	
12  V DC power supply will be used for power supply.
	 •	 When	 the	LAN	 cable	 is	disconnected	 once,	reconnect	 the	cable	 after	around	 2	seconds.	 When	
the cable is quickly reconnected, the power may not be supplied from the PoE device.
 
     
						

							25
Connection example when connecting to a network using a 
PoE hub

LAN	cable	(category	5	or	better,	straight,	STP*)
*	PAL	models	onlyImportant:
	 •	 The	 camera	is	to	 be	 connected	 only	to	PoE	 networks	 without	routing	to	the	 outside	 plant	when	
using PoE.
	 •	 Use	a	switching	hub	or	a	router	which	is	compliant	with	10BASE-T/100BASE-TX.
	 •	 Power	 supply	is	required	 for	each	 network	 camera.	 When	using	a	PoE	 device	 (hub),	12	V	DC	
power supply is unnecessary.
 
PCLAN cable 
(category 5 or better, straight, STP*) LAN cable 
(category 5 or better, straight, STP*)
LAN cable 
(category 5 or better, straight, STP*) PoE device (hub) 
						

							26
Configure the network settings
Install the software
Before installing the software, refer to the readme file on the provided CD-ROM first.
Software included on the provided CD-ROM
	 •		Panasonic	IP	setting	software
    Configure the network settings of the camera. Refer to the following for further\
 information.
	 •	 	Viewer	Software	"Network	Camera	View	4S"
    It is necessary to install the viewer software "Network Camera View 4S" to display images on a 
PC. Install the viewer software by double-clicking the "nwcv4Ssetup.exe" icon on the provided 
CD-ROM.
Configure the network settings of the camera using the 
Panasonic IP setting software
It is possible to perform the network settings of the camera using the IP setup software on the pro-
vided CD-ROM.
When  using  multiple  cameras,  it  is  necessary  to  configure  the  network  settings  of  each  camera 
independently.
If  the  Panasonic  IP  setting  software  does  not  work,  configure  the  network  settings  of  the  camera 
and  the  PC  individually  on  the  "Network"  page  of  the  setup  menu.  Refer  to  the  Operating 
Instructions (PDF) for further information.
Important:
	 •	 When	 using	Microsoft	 Windows	 Vista,	the	"Windows	 Security	Alert"	window	 may	be	displayed	
when starting the IP setup software. In this case, disable "User Account Control" from the con-
trol panel.
	 •	 For	 the	security	 enhancement,	 the	MAC	 address/IP	 address	of	the	 camera	 to	be	 configured	 will	
not be displayed when around 20 minutes have passed after turning on the power of the cam-
era. (When "Easy IP Setup accommodate period" is set to "20min")
	 •	 Panasonic	IP	setting	software	is	inoperable	in	other	subnets	via	the	same	router.
	 •	 This	 camera	cannot	be	displayed	 or	set	 with	 an	older	 version	 of	the	 IP	setup	 software	 (version	
2.xx).
 
     
						

							27
z Start the Panasonic IP setting software.
x Click  the  [IP  setting]  button  after  selecting  the 
MAC  address/IP  address  of  the  camera  to  be 
configured.
Note:
	 •	 When	 using	a	DHCP	 server,	 the	IP	address	
assigned  to  the  camera  can  be  displayed  by 
clicking  the  [Refresh]  button  of  the  IP  setting 
software.
	 •	 When	 a	duplicate	 IP	address	 is	used,	 the	corre-
sponding  MAC  address/IP  address  will  be  dis-
played shaded.
 
c  Complete  each  network  setup  item  and  click 
the [Apply] button.
Note:
	 •	 When	 using	a	DHCP	 server,	 it	is	 possible	 to	set	
"DNS" to "AUTO".
 
Important:
	 •	 It	 may	take	 for	around	 2	minutes	 to	complete	 to	upload	 the	settings	 to	the	 camera	 after	clicking	
the  [Apply]  button.  The  settings  may  be  invalidated  when  the  12  V  DC  power  supply  is  cut  or 
when  the  LAN  cable  is  disconnected  before  completing  the  upload.  In  this  case,  perform  the 
settings again.
	 •	 When	using	a	firewall	(including	software),	allow	access	to	all	UDP	ports.
  
						

							28
Troubleshooting
Before asking for repairs, check the symptoms with the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the 
table or a problem is not described below.
SymptomCause/solutionReference 
pages
Power is not turned on. When using DC power supply
	 •	 Is	12	V	DC	power	supply	connect	to	the	
power supply terminal? 
→  Check whether the connection is appropri-
ately established.
	 •	 Is	the	AC	adaptor	in	use	compliant	with	the	 Specifications? 
→  Check the Specifications regarding AC 
adaptor.
When using a PoE device for power supply
	 •	 Are	the	PoE	device	and	the	network	connector	 on the rear of the camera connected using a 
LAN cable (4-pair)? 
→  Check whether the connection is appropri-
ately established.
	 •	 Depending	on	the	PoE	device,	the	power	sup- ply will stop when the demanded power 
exceeds its total power limit for all PoE ports. 
→  Refer to the operating instructions of the 
PoE device in use. 23, 24 
						

							29
Specifications
● Basic
Power source: 12 V DC, PoE (IEEE802.3af compliant)
Power consumption:  WV-SP105
	 	 	 12	V	DC*:	200	mA,
     PoE: 2.8 W (Class 2 device)
    WV-SP102
	 	 	 12	V	DC*:	140	mA,
     PoE: 2.0 W (Class 2 device)
	 	 *		FOR	UL	LISTED	MODEL(S),	ONLY	CONNECT	12	V	DC	
CLASS 2 POWER SUPPLY. 
Ambient operating temperature:  0 °C to +40 °C {32 F° to 104 F°}
Ambient operating humidity:  Less than 90 % (no condensation)
Dimensions:  55 mm (W) x 55 mm (H) x 122 mm (D)  
{2-5/32 inches (W) x 2-5/32 inches (H) x 4-13/16 inches (D)}  
(excluding connectors/terminals)
Mass:  WV-SP105: Approx. 180 g {0.40 lbs}
    WV-SP102: Approx. 170 g {0.38 lbs}
Finish:  Fine silver (501)
 
● Camera
Image sensor:  WV-SP105: 1/3 type MOS image sensor
    WV-SP102: 1/5 type MOS image sensor
Effective pixels:  WV-SP105: Approx. 1.3 megapixels
    WV-SP102: Approx. 0.32 megapixels
Scanning area:  WV-SP105: 4.80 mm (H) × 3.60 mm (V)  
{3/16 inches (H) × 5/32 inches (V)}
    WV-SP102: 2.69 mm (H) × 2.02 mm (V)  
{7/64 inches (H) × 3/32 inches (V)}
Scanning system:  Progressive
Minimum illumination:  WV-SP105:
     Color:    0.8 lx {0.08 footcandle} (F2.2, Auto slow shutter: 
Off (1/30 s), AGC: High)
         0.05 lx {0.005 footcandle} (F2.2, Auto slow shut-
ter:	max.	16/30	s,	AGC:	High)*
     BW:    0.4 lx {0.04 footcandle} (F2.2, Auto slow shutter: 
Off (1/30 s), AGC: High)
         0.03 lx {0.003 footcandle} (F2.2, Auto slow shut-
ter:	max.	16/30	s,	AGC:	High)*	 
*	Converted	value
    WV-SP102:
     Color:    2.0 lx {0.2 footcandle} (F2.0, Auto slow shutter: 
Off (1/30 s), AGC: High) 
         0.3 lx {0.03 footcandle} (F2.0, Auto slow shutter: 
max.	8/30	s,	AGC:	High)*	
     BW:    1.3 lx {0.13 footcandle} (F2.0, Auto slow shutter: 
Off (1/30 s), AGC: High)
         0.16 lx {0.016 footcandle} (F2.0, Auto slow shut-
ter:	max.	8/30	s,	AGC:	High)* 
*	Converted	value 
						

							30
Gain (AGC): On(Low)/ On(Mid)/ On(High)/ Off
Adaptive black stretch:  On/Off
Light control mode setting:  Indoor scene (50 Hz/60 Hz)/ ELC
Maximum exposure time:  WV-SP105: 
       1/30 s, 3/100 s, 3/120 s, 2/100 s, 2/120 s, 1/100 s, 
1/120 s, 1/250 s, 1/500 s, 1/1000 s, 1/2000 s, 1/4000 s, 
1/10000 s
    WV-SP102: 
       1/30 s, 3/100 s, 3/120 s, 2/100 s, 2/120 s, 1/100 s, 
1/120 s, 1/250 s, 1/500 s, 1/1000 s, 1/2000 s, 1/4000 s, 
1/8000 s
Auto slow shutter:  WV-SP105: 
     Off(1/30 s), max. 2/30 s, max. 3/30 s, max. 4/30 s, 
     max. 6/30 s, max. 10/30 s, max. 16/30 s
    WV-SP102: 
     Off(1/30 s), max. 2/30 s, max. 3/30 s, max. 4/30 s, 
     max. 8/30 s
Simple black & white mode:  Off/AUTO
White balance:  ATW1/ ATW2/ AWC
Digital noise reduction:  High/Low
Privacy zone:  On/Off (up to 2 zones available)
Camera title on screen:  Up to 16 characters (alphanumeric characters, marks) On/Off
VMD alarm:  On/Off, 4 areas available
● Lens
Zoom ratio: WV-SP105: 2x with Extra Zoom under VGA
    WV-SP102: -
Focal length:  WV-SP105: 3.54 mm
    WV-SP102: 2.00 mm
Maximum aperture ratio:  WV-SP105: 1:2.2
    WV-SP102: 1:2.0
Focus range:  0.5 m - ∞
Angular field of view:  WV-SP105: Horizontal: 70.3 °, Vertical: 55.4 °
    WV-SP102: Horizontal: 66.9 °, Vertical: 52.3 °
● Network
Network: 10BASE-T/ 100BASE-TX, RJ45 connector
Resolution:  WV-SP105: 
     Aspect ratio: 4:3
     H.264    1280×960/ VGA (640×480)/ QVGA (320×240),  
max. 30 fps
     JPEG    1280×960/ VGA (640×480)/ QVGA (320×240),  
max. 30 fps
     Aspect ratio: 16:9
     H.264  1280×720/ 640×360/ 320×180, max. 30 fps
     JPEG  1280×720/ 640×360/ 320×180, max. 30 fps
    WV-SP102: 
     Aspect ratio: 4:3
     H.264  VGA (640×480)/QVGA (320×240), max. 30 fps
     JPEG  VGA (640×480)/QVGA (320×240), max. 30 fps
     Aspect ratio: 16:9
     H.264  640×360/ 320×180, max. 30 fps
     JPEG  640×360/ 320×180, max. 30 fps