Panasonic Network Camera WV-SF549 WV-SF548 WV-SF539 WV-SF538 Installation Guide

31
Vertical position (Tilting)
Loosen the tilting lock screws (x2), and rotate 
the tilting table to adjust the tilting direction. 
(Adjustable range: ±75 °) Since a variable focal 
lens is used, it is possible to change the angu-
lar field of view. This lens can also be rotated in 
the reverse direction, but the image azimuth is 
reversed. In this case, the image azimuth can 
be modified when the panning table is rotated 
to the direction of clockwise panning (180 °). 

Horizontal: 24.20° (TELE) to...

32
x  Adjust the angular field of view and the focus. 
  Adjust the angular field of view in accordance with the distance between the camera lens and a 
photographic subject. These adjustments shall be performed together with the camera angle 
adjustment.
Zoom lock knob
Loosen TightenFocus ring
* Do not move the focus ring. Auto focus (AF) button
 q  Loosen the zoom lock knob and move the knob between TELE and WIDE to obtain the appro-
priate angle of view.
 w  Press the auto focus (AF) button twice...

33
Note:
  •  If the zoom lock knob is fully turned in the W direction, the periphery may become dark. In 
such a case, turn the zoom lock knob in the T direction for readjustment.
  •  If the zoom lock knob is slightly tightened before the zoom is adjusted, the knob will become 
stable, making fine adjustments easier to perform.
  • When shooting in the following place or the following subjects, focus may not be adjusted 
automatically. In this case, adjust the focus manually from the setup menu. Refer...

34
Attaching the dome cover
FRONT 
TOP
MONITOROUTLOCK
Auto focus (AF)
button
Attach the dome cover to the camera. SF549 SF548
The following procedure is required when using WV-SF549 or WV-SF548. Refer to page 35 when 
using WV-SF539 or WV-SF538. 
   
z  Attach the inner dome to the camera in the 
same manner as the procedure in page 30. 
  Make sure that the tilting lock screws of 
the camera and the holes on the inner 
dome are correctly fit together. 
x Attach the dome cover using the bit for...

35
z Align the indication OPEN to the marker 
of the camera to attach the dome cover. 
x Remove the cover film from the dome 
cover except the dome section.
c  Adjust the direction of the inner dome. 
  Rotate the dome cover clockwise to adjust 
the marker to ADJUST. The clear dome 
and the inner dome can rotate together in 
this state. Rotate the dome section of the 
dome cover to adjust the direction so that 
no eclipse may be caused.
   
ADJUSTOPENLOCK
Marker
Dome 
cover Dome alignment 
indication...

36
v  Rotate the dome cover clockwise to adjust
the marker to LOCK. 
b Fix the dome cover and the camera with 
the dome cover fixing screw (M3, step 
screw, x1) that has been removed in the 
procedure of Detaching the dome cover 
(☞ page 17).
   (Recommended tightening torque: 
0.59  N·m {0.44 lbf·ft})
n After the installation is complete, remove 
the cover film, which was removed halfway 
in Step 2, completely from the dome sec-
tion.
m  Push down the auto focus (AF) button with 
a ballpoint pen to...

37
Configure the network settings
Configuring the camera so that it can be accessed from a PC
The following are descriptions for when the camera with default settings is configured. If you 
are using firewall software on your PC, the Setup Program may not be able to find any 
cameras on your network. Configure the setting of the camera after temporarily invalidating 
the firewall software. Contact the network administrator or your Internet service provider for 
information about configuring the settings...

38
c  Select the camera you want to configure, and click [Access Camera].
Note: 
 • When cameras are displayed in [Panasonic IP Setting] screen, click the camera with same 
MAC address as the MAC address printed on the camera that you want to configure.
v  If the installation screen of the viewer software “Network Camera View 4S” is displayed, follow 
the instructions of the wizard to start the installation. (The viewer software is installed from the 
camera.)
  •  The “Live” page will be displayed.
  •...

39
Troubleshooting
Before asking for repairs, check the symptoms with the following table. 
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the 
table or a problem is not described below. 
Symptom Cause/solutionReference 
pages
Power is not turned on. 
When using DC power supply
 •  Is 12 V DC power supply connected to 
the power supply terminal?
    Check whether the connection is 
appropriately established. 
 •  Is the AC adaptor in use compliant with...

40
Specifications
• Basic
Power source: 12 V DC, PoE (IEEE802.3af compliant)
Power consumption:
SF549 SF539
12 V DC*: 530 mA, PoE 48 V: 120 mA (Class 2 devices)SF548 SF538
12 V DC*: 510 mA, PoE 48 V: 115 mA (Class 2 devices)
*  
ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/
CSA 223) or LIMITED POWER SOURCE (IEC/EN/UL/CSA 
60950-1).
Ambient operating temperature: –10 °C to +50 °C {14 °F to 122 °F}
Ambient operating humidity:Less than 90 % (no condensation)
Shock resistance:
SF549 SF548
Compliant...