Panasonic Network Camera WV-SF549 WV-SF548 WV-SF539 WV-SF538 Installation Guide

21
Installing the camera directly on the ceiling or wall
Place the installation template label (accessory) on the ceiling or wall, and make a hole to pass the 
cable.
Remove the template label, and mount the camera by fixing 4 screws (locally procured).
(☞ Page 29)
20 mm {13/16 inches}83.5 mm {3-5/16 inches}
Cable access hole for ceiling/wall Recommended screw (M4: 4 pcs.) Side cable access hole
Direction marker for installation
Screws 
(locally procured)
Installation template label (accessory)
46 mm...

22
Insert/remove an SD memory card (WV-SF549/WV-SF539 only)
IMPORTANT:
  •  When inserting an SD memory card, make sure the direction. 
  •  Before removing the SD memory card, make sure to select “Not use” for “SD memory card” on 
the [SD memory card] tab of the “Basic” page on the setup menu first. 
  (☞ Operating Instructions (included in the CD-ROM))
 
z  Detach the dome cover. 
SF549 (☞ Page 17)
SF539(☞ Page 18)
x Insert an SD memory card fully into the SD 
memory card slot until a click is heard....

23
Connection
Before starting the connection, turn off the power of this camera and the devices to be connected. 
Check and prepare the required devices and cables for connection. 
Note:
  • Since the connector storage 
section does not have a suffi-
cient space, use audio cables 
and a LAN cable that do not 
exceed the sizes described in 
the illustrations.
 
z  Connect the RCA pin cable to the monitor out connector for adjustment (only used for adjust-
ment of the angular field of view).
IMPORTANT:
  •...

24
c Connect an external speaker with amplifier to 
the audio output connector (for use of the audio 
transmission function). 
SF549 SF539
  Connect a stereo mini plug (ø3.5 mm) (audio 
output is monaural). 
  •  Recommended cable length: 10 m 
{33 feet} or less
v Connect the cables of external devices to the 
EXT I/O terminal plug (accessory). 
 q When connecting an external device, remove 
8 mm - 9 mm {5/16 inches - 11/32 inches} of 
the outer jacket of the cable and twist the cable 
core to prevent...

25
 e  After the cable connection, connect the exter-
nal I/O terminal plug to the external I/O termi-
nals of the camera. 
   
IMPORTANT:
  •  Do not connect 2 wires or more directly to a terminal. When it is necessary to connect 2 wires 
or more, use a splitter.
  •  Input and output of the EXT I/O terminal 2 and 3 can be switched by configuring the setting. 
Off is selected by default. It is possible to determine whether or not to receive input from EXT 
I/O terminal 2 and 3 (ALARM IN2, 3) by...

26
When using 12 V DC power supply*
 q  Loosen the screws of the power cord plug 
(accessory). 
 w  Connect the cable of the 12 V DC power sup-
ply* to the power cord plug.
    Strip 3 mm - 7 mm {1/8 inches - 9/32 inches} 
from the end of the wire, and twist the stripped 
part of the wire sufficiently to avoid short circuit. 
Specification of cable (wire): 
16 AWG - 24 AWG, Single core, twisted
  •  Check whether the stripped part of the wire is 
not exposed and is securely connected.
 e  Tighten the...

27
When using PoE (IEEE802.3af compliant)
Connect a LAN cable (category 5 or better, straight, STP*) between a PoE device (such as a hub) 
and the network connector of the camera.
* For Europe
IMPORTANT:
  •  Use all 4 pairs (8 pins) of the LAN cable. 
  •  The maximum cable length is 100 m {328 feet}. 
  •  Make sure that the PoE device in use is compliant with IEEE802.3af standard. 
  •  When connecting both the 12 V DC power supply and the PoE device for power supply, 12 V 
DC will be used for power...

28
Connection example when connecting to a network using a 
PoE hub
PoE device (hub)
PCMicrophone (option)
Microphone (option)
6SHDNHUZLWKDPSOL
„HU
(option)
6SHDNHUZLWKDPSOL
„HU
(option)Video monitor 
(for adjustment use only)
Video monitor 
(for adjustment use only)
LAN cable (category 5 or 
better, straight, STP*)LAN cable (category 5 or 
better, straight, STP*)
LAN cable (category 5 or 
better, straight, STP*)

LAN cable (category 5 or better, straight, STP*)
* For Europe
IMPORTANT:
  •  The...

29
Installation
Camera mounting
Installation shall be conducted after turning off each device. 
z  Detach the dome cover. (☞ Page 17)
x  Connect the cables to the camera. (☞ Pages 23 - 28)
  As necessary, use a cable tie (accessory) to assemble the cables.
c Mount the camera. (The illustration represents the case in which a two-gang junction box is 
installed.)
    Fix the camera with 4 screws (M4, locally procured).
Direction marker for installation
(×TOP)
ADirection marker for installation
(FRONTØ)...

30
Adjustment
z Adjust the camera angle. When determining the camera angle, repeat fine adjustments by 
gradually moving the panning table, tilting table, and azimuth adjustment ring. 
Horizontal position (Panning)
Loosen the panning lock screw, rotate 
the panning table to adjust the pan 
direction. (Adjustable range: 350 °)
Panning is possible within the range 
of 180 ° (when panning clockwise) 
and 170 ° (when panning counter-
clockwise). After adjustment, tighten 
the panning lock screw to fix the...