Panasonic Network Camera Wv Sf332 Installation Guide

21
Installing the camera directly on the ceiling or wall
Place the installation template label (accessory) on the ceiling or wall, and make a hole to pass the 
cable.
Remove  the  template  label,  and  mount  the  camera  by  fixing  4  screws  (locally  procured).  (☞  Page 
28 )
FRONT 
TOPEXT I/O
AUDIO
OUTMIC
LINE IN 10BAS
100BA
12V=IN
4 2
3 1MONITOR
OUT
N
F
20 mm {13/16}
83.5 mm {3-5/16}
Direction marker for installation
Cable access hole for ceiling/wall
Recommended screw (M4: 4 pcs.)
Side cable...

22
Insert/remove an SDHC/SD memory card
Important:
	 •	 Before	inserting	the	SDHC/SD	memory	card,	turn	off	the	power	of	the	camera	first.	
	 •	 When	inserting	an	SDHC/SD	memory	card,	make	sure	the	direction.	
	 •	 Before	 removing	the	SDHC/SD	 memory	card,	select	 "Not	use"	for	"SD	 memory	 card"	on	the	
[SD memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and 
then  unload  the  SDHC/SD  memory  card.  When  the  SDHC/SD  memory  card  is...

23
Connection
Before starting the connection, turn off the power of this camera and the devices to be connected. 
Check and prepare the required devices and cables for connection. Note:
	 •	 Since  the  connector  storage 
section  does  not  have  a  suffi-
cient  space,  use  audio  cables 
and  a  LAN  cable  that  do  not 
exceed  the  sizes  described  in 
the illustrations.
 
z Connect the RCA pin cable to the monitor out connector for adjustment (only used for adjust-
ment of the angular field of...

24
c Connect  an  external  speaker  with  amplifier  to 
the audio output connector (for use of the audio 
transmission function). 
  Connect  a  stereo  mini  plug  (ø3.5  mm)  (monau-
ral output). 
	 •	 Recommended	cable	length:	Less	than	  10 m {33'}
v Connect  the  cables  of  external  devices  to  the 
EXT I/O terminal plug (accessory). 
  q  When  connecting  an  external  device,  remove 
8 mm  -  9  mm  {5/16"  -  11/32"}  of  the  outer 
jacket  of  the  cable  and  twist  the...

25
Important:
	 •	 Do	 not	connect	 2	wires	 or	more	 directly	 to	a	terminal.	 When	it	is	 necessary	 to	connect	 2	wires	
or more, use a splitter. 
	 •	 Connect	an	external	device	with	verifying	that	the	ratings	are	within	the	specifications	above.	
	 •	 When	 using	the	EXT	 I/O	terminals	 as	the	 output	 terminals,	 ensure	they	do	not	 cause	 signal	col-
lision with external signals. 
 
	 •	 ALARM	OUT,	AUX	OUT Output specification: Open collector output (maximum applied voltage: 20 V DC)
Open: 4 V - 5...

26
Important:
	 •	 Be	sure	to	use	the	power	cord	plug	provided	with	this	product.	
	 •	 Be	 sure	to	fully	 insert	 the	power	 cord	plug	into	the	12	V	DC	 power	 supply	 terminal	 (accessory).	
Otherwise, it may damage the camera or cause malfunction. 
	 •	 Be	 sure	to	use	 an	AC	 adaptor  compliant  with  the  Specifications  regarding  power  source  and 
power consumption (☞ page 39). 
 
  t  Run the 12 V DC output cable through the gap of the cable hook. 
12V=IN
12 V DC output cable
Cable hook
When...

27
Connection example when connecting to a network using a 
PoE hub
PoE device (hub)
PCMicrophone (option)
Microphone (option)
Speaker with amplier 
(option)
Speaker with amplier 
(option)Video monitor 
(for adjustment use only)
Video monitor 
(for adjustment use only)
LAN cable (category 5 or 
better, straight, STP*) LAN cable (category 5 or 
better, straight, STP*)
LAN cable (category 5 or 
better, straight, STP*)

LAN cable (category 5 or better, straight, STP*)
* PAL models only Important:
	 •	 The...

28
Installation
Camera mounting
Installation shall be conducted after turning off each device. 
z Detach the dome cover. (☞ Page 18)
x Connect the cables to the camera. (☞ Pages 23 to 27)
  As necessary, use a cable tie (accessory) to assemble the cables.
c Mount  the  camera.  (The  illustration  represents  the  case  in  which  a  two-gang  junction  box  is 
installed.)
	 •	 Fix	the	camera	with	4	screws	(M4,	locally	procured)
FRONT 
TOPEXT I/O
AUDIO
OUTMIC
LINE IN 10BAS
100BA
12V=IN
4
2
3 1MONITOR...

29
Adjustment
z Adjust  the  camera  angle.  When  determining  the  camera  angle,  repeat  fine  adjustments  by 
gradually moving the panning table, tilting table, and azimuth adjustmen\
t ring. 
Horizontal position (Panning)
Loosen  the  panning  lock  screw,  rotate  the  panning  table  to  adjust  the  pan  direction.  (Adjustable 
range: 350 °)
Panning  is  possible  within  the  range  of  180  ° (when  panning  clockwise)  and  170  °  (when  panning 
counterclockwise). After adjustment,...

30
Note:
	 •	 When	 the	camera	 is	used	 at	an	 angular	 field	of	view	 that	is	close	 to	horizontal,	 it	must	 be	noted	
that the shadow of the dome cover may be projected. 
 
Image tilt adjustment
Rotate  the  azimuth  adjustment  ring  to  adjust  the  azimuth  angle  of  the  image.  (Adjustable  range: 
±100	°)
FRONT 
TOP
MONITOR OUT
LOCK
12V=INBASE-T/
BASE TX
EXT–100 ° +100 °
Adjustable range
x Adjust the angular field of view and the focus. SF336
  Adjust the angular field of view in accordance...