Panasonic Network Camera Wv Sf332 Installation Guide

11
Precautions
Refer installation work to the dealer. 
Installation work requires technique and experi-
ences.  Failure  to  observe  this  may  cause  fire, 
electric  shock,  injury,  or  damage  to  the  prod-
uct. 
Be sure to consult the dealer. 
Stop the operation immediately when 
something is wrong with this product. 
When  smoke  goes  up  from  this  product  or  the 
smell  of  smoke  comes  from  this  product,  stop 
the  operation  immediately  and  contact  your 
dealer. 
Turn  the  power...

12
Turn the power off when cleaning of this 
product. 
Failure to observe this may cause injury. 
[Precautions for use]
This product is designed to be used 
indoors. This product is not operable out-
doors. 
This product has no power switch. 
When  turning  off  the  power,  turn  off  a  circuit 
breaker. 
To keep on using with stable performance
Do  not  use  this  camera  in  hot  and  humid  con-
ditions for a long time. 
Failure to observe this causes component deg-
radation resulting in life...

13
	 •	 When	using	an	unformatted	 SDHC/SD	
memory  card,  format  it  using  this  camera. 
Recorded  data  on  the  SDHC/SD  memory 
card  will  be  deleted  when  formatted.  If  an 
unformatted SDHC/SD memory card or an 
SDHC/SD  memory  card  formatted  with 
other devices is used, this product may not 
work properly or performance deterioration 
may  be  caused.  Refer  to  the  Operating 
Instructions  (PDF)  for  how  to  format  a 
SDHC/SD memory card. 
	 •	 When	 some	SDHC/SD	 memory	cards	are...

14
Precautions for Installation
Installation work shall be performed in accordance with the technology standard of the 
electric installation. 
    
This camera is designed to be used 
indoors. 
This product is not operable outdoors. 
Do not expose this camera to direct sunlight for 
hours  and  do  not  install  the  product  near  a 
heater  or  an  air  conditioner.  Otherwise,  it  may 
cause  deformation,  discoloration  and  malfunc-
tion.  Keep  this  camera  away  from  water  and 
moisture....

15
Radio disturbance
When this product is used near TV/radio anten-
na, strong electric field or magnetic field (near a 
motor,  a  transformer  or  a  power  line),  images 
may be distorted and noise sound may be pro-
duced. 
PoE (Power over Ethernet)
Use  a  PoE  hub/device  that  is  compliant  with 
IEEE802.3af standard. 
Router
When  connecting  this  product  to  the  Internet, 
use  a  broadband  router  with  the  port  forward-
ing function (NAT, IP masquerade). 
Refer  to  the  Operating...

16
Major operating controls
 * This  connector  is  provided  only  for  service.  Do  not  use  the  connector  for  checking  the  adjust-
ment of the angular field of view on the video monitor. 
    
FRONT 
TOP
MONITOR OUT
LOCK
12V   INBASE-T/
BASE TX
EXT
TOP
Marker
Direction marker for installation
Azimuth adjustment ring
Tilting table
Panning lock screw [LOCK] Panning table
Inner dome
Clear domeDome cover
(Provided only for service)
Monitor out connector for 
service*
Monitor out 
connector for...

17

About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for around 5 seconds or more without releasing this button. Wait around 2 minutes 
after  releasing  the  button.  The  camera  will  start  up  and  the  settings  including  the  network  settings 
will  be  initialized.  Before  initializing  the  settings,  it  is  recommended  to  write  down  the  settings  in 
advance. 
FOCUS 
ASSIST
Tilting lock...

18
Detaching the dome cover
Important:
	 •	 After	 removal,	retain	the	dome	 cover	fixing	screw	 so	as	not	 to	lose.	 The	screw	 is	required	 when	
attaching the dome cover. (☞ Page 34)
	 •	 Remove	 the	cover	 film	from	 the	dome  section  of  the  dome  cover  after  the  installation  is  com-
plete. Do not touch the dome section by hand directly after removing the cover film. 
z  Remove  the  dome  cover  fixing  screw  (M3, 
step screw, x1). 
x Rotate  the  dome  cover  counterclockwise  two  steps,...

19
Preparations
When  installing  the  camera  on  a  wall  or  a  ceiling,  there  are  four  methods  as  specified  below.  
(☞ Pages 20 and 21).
	 •	 Using	the	two-gang	junction	box
	 •	 Installing	the	camera	directly	on	the	ceiling	or	wall
	 •	 Using	the	optional	ceiling	mount	bracket	WV-Q168	(for	embedded	installation	on	a	ceiling)
	 •	 Using	the	optional	ceiling	mount	bracket	WV-Q105*
1 (for direct mounting on a ceiling) 
Important:
	 •	 Procure	 4	screws	 (M4)	to	secure	 the	camera	 to	a	wall	 or...

20
Using the side cable access hole
When  installing  the  camera  directly  on  the  ceiling  or  wall  with  cables  exposed  or  when  using  the 
optional  ceiling  mount  bracket  WV-Q168,  cut  out  a  portion  of  the  dome  cover  to  open  a  cable 
access hole.
Side cable access hole
Side cable access hole
Method of camera installation
Using the two-gang junction box
Mount the camera on the two-gang junction box by fixing 4 screws (locally procured). (☞ Page 28)
FRONT 
TOPEXT I/O
AUDIO
OUTMIC...