Panasonic Network Camera Wv Sf332 Installation Guide

							21
Installing the camera directly on the ceiling or wall
Place the installation template label (accessory) on the ceiling or wall, and make a hole to pass the 
cable.
Remove  the  template  label,  and  mount  the  camera  by  fixing  4  screws  (locally  procured).  (☞  Page 
28 )
FRONT 
TOPEXT I/O
AUDIO
OUTMIC
LINE IN 10BAS
100BA
12V=IN
4 2
3 1MONITOR
OUT
N
F
20 mm {13/16}
83.5 mm {3-5/16}
Direction marker for installation
Cable access hole for ceiling/wall
Recommended screw (M4: 4 pcs.)
Side cable access hole
Screws 
(locally procured)
Installation template label (accessory)46 mm 
{1-13/16}
40 mm {1-9/16}
Using the optional ceiling mount bracket WV-Q168
It  is  possible  to  reduce  the  exposed  portion  of  the  camera  body  using  the  optional  ceiling  mount 
bracket.  Refer  to  WV-Q168  Operating  Instructions 
or  "Installation"  (☞  page  28)  for  how  to  mount  the 
camera. 
Using the optional ceiling mount 
bracket WV-Q105 (PAL models only)
Refer to WV-Q105 Operating Instructions and "Installation" (☞ page 28) for how to mount the cam-
era in case of using the optional ceiling mount bracket.
Anchor bolt
Safety wire angle Roof space
Safety wire
Camera
WV-Q105 (option)
(4 pcs, WV-Q105 supplied)
Cable tie (accessory)
Ceiling board such 
as plaster board 
						

							22
Insert/remove an SDHC/SD memory card
Important:
	 •	 Before	inserting	the	SDHC/SD	memory	card,	turn	off	the	power	of	the	camera	first.	
	 •	 When	inserting	an	SDHC/SD	memory	card,	make	sure	the	direction.	
	 •	 Before	 removing	the	SDHC/SD	 memory	card,	select	 "Not	use"	for	"SD	 memory	 card"	on	the	
[SD memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and 
then  unload  the  SDHC/SD  memory  card.  When  the  SDHC/SD  memory  card  is  inserted  or 
removed  with  the  power  on,  data  in  the  SDHC/SD  memory  card  may  be  damaged.   
(☞ Operating Instructions (PDF))
 
z  Detach the dome cover. (☞ Page 18)
x Insert  an  SDHC/SD  memory  card  fully  into  the 
SDHC/SD memory card slot. 
c Attach the dome cover. (☞ Page 34)
v When  removing  the  SDHC/SD  memory  card 
from  the  SDHC/SD  memory  card  slot,  detach 
the  dome  cover  (☞  page  18),  and  push  the 
card  until  the  lock  is  released.  After  removal, 
attach the dome cover. (☞ Page 34)
SDHC/SD memory card slot
Dome cover Dome cover xing screw
(M3, step screw) 
						

							23
Connection
Before starting the connection, turn off the power of this camera and the devices to be connected. 
Check and prepare the required devices and cables for connection. Note:
	 •	 Since  the  connector  storage 
section  does  not  have  a  suffi-
cient  space,  use  audio  cables 
and  a  LAN  cable  that  do  not 
exceed  the  sizes  described  in 
the illustrations.
 
z Connect the RCA pin cable to the monitor out connector for adjustment (only used for adjust-
ment of the angular field of view). (☞ Page 16) 
Important:
	 •	 The	 monitor	out	connector	 for	service	 is	provided	 only	for	checking	 the	adjustment	 of	the	 angu-
lar field of view on the video monitor when installing the camera or when servicing. It is not pro-
vided for recording/monitoring use. 
	 •	 When	 checking	the	adjustment	 of	the	 angular	 field	of	view	 on	the	 video	 monitor,	 be	sure	 to	use	
the RCA jack of the main body for connection with video monitor. 
	 •	 Black	 bands	may	appear	 at	the	 top	 and	 bottom	 or	right	 and	left	of	the	 screen.	 (That	does	not	
affect the adjustment because the angular field of view is not changed.)
	 •	 The	 video	output	 on	the	 monitor	 for	adjustment	 does	not	guarantee	 the	video	 performance	 or	
image quality.
 
x  Connect  the  microphone  to  MIC/LINE  IN  (for 
use of the audio reception function). 
  Input impedance: Approx. 2 kΩ
  Recommended cable length:
    1 m {3.3'} or less (for microphone input) 
10 m {33'} or less (for LINE input)
  Recommended microphone:
    Plug-in power type microphone (option) 
Connect a monaural mini plug (ø3.5 mm).
	 •	 Supply	voltage:	2.5	V±0.5	V
	 •	 Recommended	sensitivity	of	microphone:	  –48	dB	±3	dB	(0	dB=1	V/Pa,1	kHz)
    FRONT 
TOPEXT I/O
AUDIO
OUT MIC/
LINE IN10BASE-T/
100BASE-IX
4
2
3 1
MONITOR
OUT
FIN
Microphone/line 
input connector
Straight section
17 mm {21/32}
30 mm {1-3/16}
ø9 mm 
{11/32}Example of 
audio cable connector
40 mm {1-9/16}Straight section
30 mm {1-3/16}
9 mm 
{11/32}
13 mm {1/2}Example of LAN cable 
connector
Caution:
	 •	 FOR	UL	LISTED	MODEL(S),	ONLY	CONNECT	12	V	DC	CLASS	2	POWER	SUPPLY. 
						

							24
c Connect  an  external  speaker  with  amplifier  to 
the audio output connector (for use of the audio 
transmission function). 
  Connect  a  stereo  mini  plug  (ø3.5  mm)  (monau-
ral output). 
	 •	 Recommended	cable	length:	Less	than	  10 m {33'}
v Connect  the  cables  of  external  devices  to  the 
EXT I/O terminal plug (accessory). 
  q  When  connecting  an  external  device,  remove 
8 mm  -  9  mm  {5/16"  -  11/32"}  of  the  outer 
jacket  of  the  cable  and  twist  the  cable  core  to 
prevent the short circuit first. 
Specification of cable (wire): 20 AWG -  
26 AWG
    Single core, twisted
  w  Push  down  the  button  of  the  desired  terminal 
on the external I/O terminal plug with a ballpoint 
pen,  and  release  the  button  when  the  cable  of 
the  external  device  is  fully  inserted  into  the  ter -
minal  hole.  Make  sure  that  the  cable  is  firmly 
connected to the terminal. 
  e  After  the  cable  connection,  connect  the  exter -
nal  I/O  terminal  plug  to  the  external  I/O  termi-
nals of the camera. 
  * Check  whether  the  stripped  part  of  the  wire  is 
not exposed and is securely connected. 

    
8 mm - 9 mm
{5/16 - 11/32} Strip range
4321
External I/O terminal plug
Button
FRONT 
TOPEXT I/O
AUDIO
OUT
MIC/
LINE IN10BASE-T/
100BASE-IX
4
2
3 1
MONITOR
OUT
FIN
External I/O terminals
FRONT 
TOPEXT I/O
AUDIO
OUT MIC/
LINE IN10BASE-T/
100BASE-IX
4
2
3 1
MONITOR
OUT
FIN
Audio output 
connector
1
2
3
4
e AUX OUT r GND
q ALARM IN
w ALARM OUT
Important:
	 •	 Connect/disconnect	 the	audio	 cables	 and	turn	 on	the	 power	 of	the	 camera	 after	turning	 off	the	
power of the audio output devices. Otherwise, loud noise may be heard from the speaker. 
 
     
						

							25
Important:
	 •	 Do	 not	connect	 2	wires	 or	more	 directly	 to	a	terminal.	 When	it	is	 necessary	 to	connect	 2	wires	
or more, use a splitter. 
	 •	 Connect	an	external	device	with	verifying	that	the	ratings	are	within	the	specifications	above.	
	 •	 When	 using	the	EXT	 I/O	terminals	 as	the	 output	 terminals,	 ensure	they	do	not	 cause	 signal	col-
lision with external signals. 
 
	 •	 ALARM	OUT,	AUX	OUT Output specification: Open collector output (maximum applied voltage: 20 V DC)
Open: 4 V - 5 V DC by internal pull-up
Close: Output voltage 1 V DC or less (50 mA or less)
	 •	 ALARM	IN Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF: Open or 4 V - 5 V DC
ON: Make contact with GND (required drive current: 1 mA or more)
b Connect  a  LAN  cable  (category  5  or  better , 
straight, STP*) to the network connector.
  * PAL models only
n Connect the power supply . 
Important:
	 •	 The	 12	V	DC	 power	 supply	 shall	be	insulated	
from the commercial AC power. 
 
When using 12 V DC power supply
  q  Loosen  the  screw  of  the  power  cord  plug 
(accessory). 
  w  Connect  the  cable  of  the  12  V  DC  power  sup-
ply* to the power cord plug.
    Strip 3 mm - 7 mm {1/8" - 9/32"} from the end 
of  the  wire,  and  twist  the  stripped  part  of  the 
wire sufficiently to avoid short circuit. 
Specification of cable (wire):  
16 AWG - 24 AWG, Single core, twisted
  •  Check  whether  the  stripped  part  of  the  wire  is 
not exposed and is securely connected.
  e  Tighten the screw of the power cord plug. 
  r  Connect  the  power  cord  plug  to  the  12  V  DC 
power supply terminal. 
  *  FOR  UL  LISTED  MODEL(S),  ONLY  CONNECT 
12 V DC CLASS 2 POWER SUPPLY.
    
FRONT 
TOPEXT I/O
AUDIO
OUT MIC/
LINE IN10BASE-T/
100BASE-IX
4
2
3 1
MONITOR
OUT
FIN
Network connector
(12 V DC)(GND)
12 V DC power cord 
plug (accessory) 
						

							26
Important:
	 •	 Be	sure	to	use	the	power	cord	plug	provided	with	this	product.	
	 •	 Be	 sure	to	fully	 insert	 the	power	 cord	plug	into	the	12	V	DC	 power	 supply	 terminal	 (accessory).	
Otherwise, it may damage the camera or cause malfunction. 
	 •	 Be	 sure	to	use	 an	AC	 adaptor  compliant  with  the  Specifications  regarding  power  source  and 
power consumption (☞ page 39). 
 
  t  Run the 12 V DC output cable through the gap of the cable hook. 
12V=IN
12 V DC output cable
Cable hook
When using PoE (IEEE802.3af compliant)
Connect  a  LAN  cable  (category  5  or  better,  straight,  STP*)  between  a  PoE  device  (such  as  a  hub) 
and the network connector of the camera.
* PAL models only
Important:
	 •	 Use	all	4	pairs	(8	pins)	of	the	LAN cable. 
	 •	 The	maximum	cable	length	is	100	m	{328'}.	
	 •	 Make	sure	that	the	PoE	device	in	use	is	compliant	with	IEEE802.3af	standard.	
	 •	 When	 connecting	 both	the	12	V	DC	 power	 supply	 and	the	PoE	 device	 for	power	 supply,	 PoE	
will be used for power supply. 
	 •	 When	 disconnecting	 the	LAN	 cable	 once,	 reconnect	 the	cable	 after	about	 2	seconds.	 When	
the cable is quickly connected, the power may not be supplied from the PoE device. 
 
     
						

							27
Connection example when connecting to a network using a 
PoE hub
PoE device (hub)
PCMicrophone (option)
Microphone (option)
Speaker with amplier 
(option)
Speaker with amplier 
(option)Video monitor 
(for adjustment use only)
Video monitor 
(for adjustment use only)
LAN cable (category 5 or 
better, straight, STP*) LAN cable (category 5 or 
better, straight, STP*)
LAN cable (category 5 or 
better, straight, STP*)

LAN cable (category 5 or better, straight, STP*)
* PAL models only Important:
	 •	 The	 video	monitor	 is	used	 for	checking	 the	adjustment	 of	the	 angular	 field	of	view	 when	 install-
ing the camera or when servicing. It is not provided for recording/monitoring use. 
	 •	 Use	a	switching	hub	or	a	router	which	is	compliant	with	10BASE-T/100BASE-TX.	
	 •	 Power	 supply	is	required	 for	each	 network	 camera.	 When	using	a	PoE	 device	 (hub),	12	V	DC	
power supply is unnecessary. 
  
						

							28
Installation
Camera mounting
Installation shall be conducted after turning off each device. 
z Detach the dome cover. (☞ Page 18)
x Connect the cables to the camera. (☞ Pages 23 to 27)
  As necessary, use a cable tie (accessory) to assemble the cables.
c Mount  the  camera.  (The  illustration  represents  the  case  in  which  a  two-gang  junction  box  is 
installed.)
	 •	 Fix	the	camera	with	4	screws	(M4,	locally	procured)
FRONT 
TOPEXT I/O
AUDIO
OUTMIC
LINE IN 10BAS
100BA
12V=IN
4
2
3 1MONITOR
OUT
N
F
Direction marker for installation
Two-gang junction box
Screws 
(locally procured)
Important:
	 •	 When	tightening	the	screws,	be	careful	to	ensure	that	the	cables	does	not	tangle	the	cables.	
 
Note:
	 •	 For	ceiling	mounting
   "gFRONT"  of  direction  marker  for  installation  indicates  the  center  of  panning.  Adjustment  of 
lens direction will become easier when the camera is mounted with the "gFRONT" marker ori-
ented  to  the  desired  shooting  area.  Refer  to  the  "Adjustment"  section  (☞  pages  29  to  33)  for 
further information about adjustment. 
	 •	 For	wall	mounting
    The camera shall be mounted with the "gFRONT" marker facing upward. 
  
						

							29
Adjustment
z Adjust  the  camera  angle.  When  determining  the  camera  angle,  repeat  fine  adjustments  by 
gradually moving the panning table, tilting table, and azimuth adjustmen\
t ring. 
Horizontal position (Panning)
Loosen  the  panning  lock  screw,  rotate  the  panning  table  to  adjust  the  pan  direction.  (Adjustable 
range: 350 °)
Panning  is  possible  within  the  range  of  180  ° (when  panning  clockwise)  and  170  °  (when  panning 
counterclockwise). After adjustment, tighten the panning lock screw to fix the panning table. 
(Recommended tightening torque: 0.39 N.m {0.29 lbf·ft})
FRONT 
TOP
MONITOR OUT
LOCK
12V=INBASE-T/
BASE TX
EXT
TOP
Home position markers KPanning table
Panning lock screw 
[LOCK]
Home position
* The position where the home 
position markers are aligned
Counterclockwise panning 
end maker: (Rotation within 
the range of 170 °) Clockwise panning end 
marker: (Rotation within the 
range of 180 °)
Vertical position (Tilting)
Loosen  the  tilting  lock  screws  (x2),  and  rotate 
the  tilting  table  to  adjust  the  tilting  direction. 
(Adjustable	
range:	±75	°)	Since	 a	variable	 focal	
lens is used, it is possible to change the angu-
lar field of view. This lens can also be rotated in 
the  reverse  direction,  but  the  image  azimuth  is 
reversed.  In  this  case,  the  image  azimuth  can 
be  modified  when  the  panning  table  is  rotated 
to the direction of clockwise panning (180°).
 Horizontal: 27.7 ° (TELE) to 100.3 ° (WIDE)
Vertical: 20.8 ° (TELE) to 73.5 ° (WIDE)
After adjustment, tighten the tilting lock screws (x2) to fix the tilting table. 
(Recommended tightening torque: 0.59 N·m {0.44 lbf·ft})
    
+75 °
–75 °
Adjustable range 
						

							30
Note:
	 •	 When	 the	camera	 is	used	 at	an	 angular	 field	of	view	 that	is	close	 to	horizontal,	 it	must	 be	noted	
that the shadow of the dome cover may be projected. 
 
Image tilt adjustment
Rotate  the  azimuth  adjustment  ring  to  adjust  the  azimuth  angle  of  the  image.  (Adjustable  range: 
±100	°)
FRONT 
TOP
MONITOR OUT
LOCK
12V=INBASE-T/
BASE TX
EXT–100 ° +100 °
Adjustable range
x Adjust the angular field of view and the focus. SF336
  Adjust the angular field of view in accordance with the distance between the camera lens and a 
photographic subject. 
Zoom lock knob
Focus ring Zoom ring
Loosen Tighten
Auto focus (AF) 
button
 q  Loosen the zoom lock knob and move the knob between TELE and WIDE to obtain the appro-
priate angle of view.