Panasonic Network Camera Recorder With Viewer Software Important Information Manual

Operating Instructions
27
 You can also limit the recording capacity in the basic settings page (see page 
13). 
[Limit the destination recording capacity] and [Limit the recording capacity] 
(individual camera setting) cannot be used simultaneously.
 
When [Limit the destination recording  capacity] is set, the following window 
is displayed.
 
[Limit the destination recording capa city] in the basic settings page is 
disabled by clicking [OK]. 

Operating Instructions
28
Setting the motion detection level
You can set the level at which to start motion detection recording.
Motion detection recording only operates when the JPEG format is selected.  
If the MPEG-4 format is selected, change the format to JPEG (see page 24).
Motion Detection Page
Motion detection monitoring window
You can monitor the progress of motion detection.The cell where motion 
was detected is displayed
in red.
SettingDescription
Non Motion 
Detection OperationIf you check...

Operating Instructions
29
Note
 Check motion detection by using the motion detection monitoring window, and adjust the sett ings accordingly.
 You can center the camera image on the desired point by right-clicking in the 
motion detection monitoring window (see 
page 51).
Before or After 
DetectionSpecify the number of seconds  to record before and after the 
motion is detected.
Executing 
Commands for 
DetectionYou can specify command s that execute for motion detection. 
You can configure commands...

Operating Instructions
30
[Disabling a monitoring area]
You can specify an area of the image in which to disable motion detection.  
To specify a disabled area, click the cells that you want to disable in the motion 
detection monitoring window. Disabled areas are darkened. You can set multiple 
disabled areas.
\
Click the cells that you want to disable 
in the motion detection monitoring 
window.
Disabled areas are darkened.
By dragging the mouse (moving the 
mouse while holding down the left button),...

Operating Instructions
31
Setting the alarm/sensor detection method
You can set an alarm/sensor detection method for cameras that have an alarm/
sensor attached. 
 
Alarm/sensor recording can only be enabled for cameras set to the JPEG format 
(see page 24). 
If the camera is set to MPEG-4 format,  change the setting to JPEG format, then 
configure the alarm/sensor.
Alarm/Sensor Page
SettingDescription
Set the Alarm1/
Sensor Recording / 
Set the Alarm2 
RecordingAfter you select the check box,...

Operating Instructions
32
Note
Configure alarm/sensor detection after an alarm/sensor has been attached to 
the camera. 
 
Setting alarm/sensor detection without an alarm/sensor causes a malfunction.
Alarm enable 
conditionSpecify Alarm enable condition ([Rising : GND to Open (High)] 
or [Falling : Open (High) to GND]).
Specify the alarm enable condition after checking the alarm  
specification.
[Rising : GND to Open (High)] is selected automatically 
when [Sensor] is selected.
Before Detected/
After...

Operating Instructions
33
Configure commands to execute for detection
You can specify executing commands for motion detection and/or alarm detection. 
Specify the commands in their respective  pages when you execute the commands 
specified (see page 
29, 32, 61).
Detection Commands Page
SettingDescription
Commands for 
Camera External 
Output SettingsSet a command (Short to GND or Open) to execute at the 
external equipment that is connected to the camera for 
motion detection and/or alarm detection and...

Operating Instructions
34
[About Commands for Camera External Output Settings]
Unlocking timeUnlocking time
Execute Commands for Camera External Output Unlocking
Execute Commands for Camera External Output Settings
When you set external output unlocking 
(After 5 seconds from motion detection, alarm detection, or unlocking time)
Unlock the external output at the set time.
Unlocking time
Unlocking time
Unlocking time
Unlocking time
Execute Commands for Camera External Output Unlocking
Execute Commands...

Operating Instructions
35
[About Command Execution]
If you do not select Perform the following control when issuing a 
command in Controlling Command Execution. (After 5 seconds from motion detection, alarm detection)
Execute commands for each detection.
Execute commands
When you select Perform the following control when issuing a command  
     Execute a command only once at the start of recording
(After 5 seconds from motion detection, alarm detection)
Execute commands only at the start of decetion...

Operating Instructions
36
Adding a keyword to recorded images
You can assign keywords to manually recorded images. 
You can use keywords to search recorded images.
Keyword Page1
SettingDescription
Keyword1/
Keyword2Put a keyword to recorded images. 
Maximum 40 characters.
2 keywords (Keyword1/Keyword2) can be set.