Panasonic Network Camera Recorder With Viewer Software Important Information Manual

Operating Instructions
137
Set Destination Recording 
Capacity Limit in the range of 1 GB 
to *** GB (Drive capacity - 
Guaranteed Destination Hard Disk 
Space). Destination Recording Capacity Limit is larger than (Drive capacity - Guaranteed Destination 
Hard Disk Space).
→ Follow the instruction message.
“Limit the recording capacity” is set 
for each camera. Do you want to 
disable these settings and enable 
the Limit the destination recording 
capacity setting? [Limit the destination recording...

Operating Instructions
138
Enter English one-byte character 
in Proxy User Name.→Follow the instruction message.
Enter English one-byte character 
in Proxy Password.→Follow the instruction message.
Do you apply the proxy settings to 
all cameras? Bu t IPv6 address 
cameras are excepted. You checked [Use a proxy server] at proxy  server settings on the preferences page. (If no 
cameras are registered, this message will not 
be displayed.)
→ Follow the instruction message.
Port is already set on the...

Operating Instructions
139
The aspect ratio is incorrect. When you enlarge an image frame, maintain the aspect ration when selecting cells.
→ Follow the instruction message.
Enlarged cells may not overlap. You cannot select an already enlarged cell.
→ Follow the instruction message.
This color has already been set. 
Select a different color.→Follow the instruction message.
Multi-Playback
This color has already been set. 
Select a different color.→Follow the instruction message.
Recorded Images
This...

Operating Instructions
140
Camera Settings
MessageCause and Remedy
Camera Settings
Enter a number in one-byte 
character in Port.→Follow the instruction message.
Enter Camera Name. The Camera Name space was blank.
→ Follow the instruction message.
Enter Camera Address. The Camera Address space was blank.
→ Follow the instruction message.
Enter English one-byte character 
in Camera Address.→Follow the instruction message.
Port should be between 1 and 
65535. A number not between 1 and 65535 was...

Operating Instructions
141
Connection to the camera cannot 
be confirmed. The IP address, port 
number, proxy settings may be 
incorrect. Do you save them? The camera cannot be accessed.→ Follow the instruction message.
Connection to the camera could 
not be confirmed. The IP address, 
port number, or proxy settings may 
be incorrect. Check your settings 
and try again. The camera cannot be accessed.
→ Follow the instruction message.
The camera authentication is not 
available. Enter the correct user...

Operating Instructions
142
The MPEG-4 format cannot be 
used with the recording frequency 
or alarm/sensor recording 
settings. Disable the recording 
frequency and alarm/sensor 
recording settings first, then select 
the MPEG-4 format. If using the MPEG-4 format, the recording  frequency setting, alarm/sensor recording are 
not available.
→ Follow the instruction message.
The selected camera does not 
support audio. Set the Recording 
Setting to [Image Only]. The camera is not supporting audio, but...

Operating Instructions
143
Recording Capacity Limit
Enter a number in one-byte 
character in Recording Capacity 
Limit.→Follow the instruction message.
Enter Recording Capacity Limit. The Recording Capacity space was blank.
→ Follow the instruction message.
Recording Capacity Limit should 
be between 100 and 500000. A number not between 100 and 500000 was 
entered in the Recording Capacity blank.
→ Follow the instruction message.
Set Recording Capacity Limit in 
the range of XXX MB to XXX MB 
(Drive...

Operating Instructions
144
Recorded Images
Timer Setting
Enter Timer Name. Timer Name space was blank.→ Follow the instruction message.
Select a day of the week. There is a check in the [Day of the Week 
Setting] but no check in any of the Day 
Buttons.
→ One day or more must be selected.
Timer Name should be 24 
characters or less. Timer Name was more than 24 characters.
→ Follow the instruction message.
The recording frequency on the 
image setting is specified. Set 
Before detected and After...

Operating Instructions
145
No matching images were found. The recorded images could not be found. 
Conversion/Copying
Start Time should be within the 
recording time. The start time is not within the recording time.→ Follow the instruction message.
Set the Start Time so that it 
comes before the End Time. The start time comes after the end time.
→ Follow the instruction message.
Set the End Time so that it 
comes after the Start Time. The end time comes before the end time.
→ Follow the instruction...

Operating Instructions
146
The data could not be converted to 
WAV format. The recorded images 
do not have any audio data.You cannot convert the recorded image into 
WAV format because the recorded images do 
not have any audio data.
To use this feature, license 
registration is essential. Perform 
license registration. Some features cannot be used without license registration (JPG, MPG, WAV, ASF, AVI 
Conversion, Make Copy).
→ Perform license registration.
The copy operation was canceled. You...