Panasonic Network Camera Bl C30a Operating Instructions

							Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 61
When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
 Clicking [
						

							Operating Instructions
62
When you set [E-mail] for Transfer Method
Select [E-mail], and click [Next>]. The following page is displayed.
 Clicking [
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 63
8.Confirm the settings, and click [Save].
 New settings are saved. The buffered images are deleted.
 When finished, Success! is displayed.
9.Click [Go to Image Buffer/Transfer page].
 The Image Buffer/Transfer page is displayed.
Notes
 If you set a short interval to transfer image to a mobile phone, many E-
mails may be sent to it leading to a large phone bill. Therefore, we 
recommend you to set a long interval. In an emergency situation, the E-
mail transfer can be stopped by enabling privacy mode using a mobile 
phone (see page 26).
 Buffered images will be deleted by doing the following.
 Turning off the camera.
 Saving the settings of Image Buffer/Transfer or Date and Time.
 Executing [Restart], [Update Firmware] or [Reset to Factory Default].
 Clicking [Delete Buffered Images] on the Image Buffer/Transfer page 
(see page 57). Subject  Enter a subject with ASCII characters (see page 107) or 
characters in each language (0—44 characters for a 1-byte 
character and 0—22 characters for a 2-byte character). But 
[] is not available.
Text  Enter text with ASCII characters (see page 107) or 
characters in each language (0—63 characters for a 1-byte 
character and 0—31 characters for a 2-byte character). But 
[] and [end-of-line] key are not available.
*1But [Space], [], [], [&], [] are not available.
Setting Description 
						

							Operating Instructions
64
2.14 Buffering or Transferring Images by Sensor
The Image Buffer/Transfer page allows you to enable image buffer/transfer by E-
mail or FTP.
1.Click [Buffer/Transfer] on the Setup page.
2.Click [No.] to enable buffer/transfer.
3.Check [Enable Image Buffer/Transfer], select [Sensor] for trigger, and click 
[Next>].
 Click [Delete Buffered Images] to delete this buffered images.
 Click [Save] to save the settings. The buffered images are deleted.
 Clicking [Cancel] takes you back to the Image Buffer/Transfer page without 
saving changes.
Setting Description
Enable Image 
Buffer/Transfer Check the box to enable the buffer/transfer. Clear the box 
to disable it.
Trigger  Selecting [Timer] enables the camera to buffer/transfer the 
image by timer.
 Selecting [Sensor] enables the camera to buffer/transfer 
the image by sensor. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 65
4.Set the time, and click [Next>].
Note
The timer works by an internal clock. Set the date and time before using timer 
buffer/transfer (see page 40).
 Clicking [].
Note
If you enable the Lens Position When Triggered setting, buffer/transfer starts 
after the camera turns to the sensor position.
 Clicking [
						

							Operating Instructions
66
6.Set the image settings, and click [Next>].
 Clicking [
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 67
7.Set the image buffer frequencies and non detection time, and click [Next>].
 Clicking [
						

							Operating Instructions
68
Non detection 
time Set the length of time during which the sensor cannot be 
triggered after saving images temporarily or transmitting 
them. This function is recommended to use not to send too 
many E-mails to a mobile phone.
Note
The internal memory cannot buffer images during Non 
detection time. Because of this, images taken before 
detection are not saved in internal memory, and so cannot 
be received. Depending on the settings for image buffer/
transfer, even if it is set to, for example, take 1 image per 
second, and store 10 images, before detection, because 
the images are not stored in internal memory, if the sensor 
detects something directly after the end of Non detection 
time, the images may not be saved. Ten seconds after the 
end of Non detection time, images can be received as 
specified in the settings. Setting Description 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 69
8.Select the transfer method, and click [Next>].
 Clicking [
						

							Operating Instructions
70
When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
 Clicking [