Panasonic Network Camera Bb Hcm403a Operating Instructions

Operating Instructions
101
When you set [E-mail] for Transfer Method
Select [E-mail], and click [Next>]. The following page is displayed.
 Clicking [

Operating Instructions
102
Setting Description
SMTP Server IP 
Address or Host 
Name
*1
 If you set a server IP address, set 4 numbers (0—255) and 
3 periods such as 192.168.0.253. Note that 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name 
(1—255 characters).
 You can set an IPv6 address.
Port No.  Enter the number (1—65535). Usually set to 25.
Reply E-mail 
Address
*2 Set the senders E-mail address. We recommend you to 
set the administrators E-mail address.
Destination E-
mail...

Operating Instructions
103
How to 
authenticateThe authentication method can be selected: 
[No authentication], [POP before SMTP authentication] or 
[SMTP authentication].
POP server authentication may be required by your ISP. In 
that case, set POP before SMTP authentication.
 No authentication: No authentication when sending an e-
mail.
 POP before SMTP authentication: Some SMTP servers 
that send e-mails do not have an authentication feature. 
Therefore, the camera uses the authentication of a POP...

Operating Instructions
104
8.After you confirm the settings and click [Next>], set E-mail notification and 
click [Next>].
 If you select [Enable], the E-mail Notification When Triggered page is 
displayed. Enter the settings referring to page 102—103. 
9.Click [Save] after confirming the settings.
 The new settings are saved.
 When finished, Success! is displayed.
Note
 If you click [Save], all buffered images on the internal memory and SD memory 
card are deleted.
10.Click [Go to Trigger page].
...

Operating Instructions
105
 If you are buffering images to the internal memory, the following operations also 
delete all buffered images.
– Turning off or restarting the camera.
– Updating the camera.
– Resetting the camera to default.
– Saving the Date and Time page. 

Operating Instructions
106
4.4 Buffering or Transferring Images by Motion 
Detection Signal
Camera has a Motion Detection feature that detects movement, such as people, 
based on the preset threshold and sensitivity of Camera. You can buffer the 
camera images, transfer to an FTP server or send E-mails using the Motion 
Detection function as a trigger.
The Trigger page allows you to enable image buffer/transfer by E-mail or FTP.
Note
 The level of motion detection depends on resolution, image quality,...

Operating Instructions
107
 Click [Save] to save the settings.
 Clicking [Cancel] takes you back to the Trigger page without saving 
changes.
Note
 If you click [Save], all buffered images on the internal memory and SD 
memory card are deleted.
4.Set the time, and click [Next>].
 Clicking [

Operating Instructions
108
5.Set the image settings, and click [Next>].
 Clicking [].
fif
 Clicking [

Operating Instructions
109
Note
 Due to the network environment, object, the number of simultaneous 
access, enabling IPsec or SD memory recording, the camera may not 
record number of images that you set. In this case, set the image buffer 
frequency longer.
 Set Every [1 s], buffer [1] images for the SD memory recording.
7.Select the transfer method, and click [Next>].
 Clicking [

Operating Instructions
110
Setting Description
No Transfer, No 
Memory Overwrite If the internal memory or the SD memory card is full, 
the camera stops buffering.
No Transfer, 
Memory Overwrite If the internal memory or the SD memory card is full, 
the camera deletes the old images, and continues to 
buffer the image.
FTP  The camera transfers the image to an FTP server (see 
page 111).
E-mail  The camera transfers the image by E-mail (see 
page 113).