Panasonic Network Camera Bb Hcm403a Operating Instructions

Operating Instructions
91
Setting Description
SMTP Server IP 
Address or Host 
Name
*1
 If you set a server IP address, set 4 numbers (0—255) and 
3 periods such as 192.168.0.253. Note that 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name 
(1—255 characters).
 You can set an IPv6 address.
Port No.  Enter the number (1—65535). Usually set to 25.
Reply E-mail 
Address
*2 Set the senders E-mail address. We recommend you to 
set the administrators E-mail address.
Destination E-
mail...

Operating Instructions
92
How to 
authenticateThe authentication method can be selected: 
[No authentication], [POP before SMTP authentication] or 
[SMTP authentication].
POP server authentication may be required by your ISP. In 
that case, set POP before SMTP authentication.
 No authentication: No authentication when sending an e-
mail.
 POP before SMTP authentication: Some SMTP servers 
that send e-mails do not have an authentication feature. 
Therefore, the camera uses the authentication of a POP...

Operating Instructions
93
8.Confirm the settings, and click [Save].
 The new settings are saved.
 When finished, Success! is displayed.
9.Click [Go to Trigger page].
 The Trigger page is displayed.
Note
 If you click [Save] on the Trigger page, all buffered images on the internal 
memory and SD memory card are deleted.
 If you are buffering images to the internal memory, the following operations also 
delete all buffered images.
– Turning off or restarting the camera.
– Updating the camera.
–...

Operating Instructions
94
4.3 Buffering or Transferring Images by Alarm 
Signal
You can buffer the camera images, transfer to an FTP server or send E-mails using 
alarm as a trigger.
The Trigger page allows you to enable image buffer/transfer by E-mail or FTP.
Note
 If you are recording images to the SD memory card, refresh interval slows 
down.
 To buffer/transfer images by alarm signal, an alarm must be connected to the 
external I/O (see page 151).
1.Click [Trigger] on the Setup page.
2.Click a No....

Operating Instructions
95
4.Set the time, and click [Next>].
 Clicking [

Operating Instructions
96
5.Set the image settings, and click [Next>].
 Clicking [].
 Clicking [

Operating Instructions
97
Note
 Due to the network environment, object, the number of simultaneous 
accesses, enabling IPsec or SD memory recording, the camera may not 
record number of images that you set. In this case, set the image buffer 
frequency longer. 
 Set Every [1 s], buffer [1] images for the SD memory recording.
7.Select the transfer method, and click [Next>].
 Clicking [

Operating Instructions
98
Setting Description
No Transfer, No 
Memory 
Overwrite If the internal memory or the SD memory card is full, the 
camera stops buffering.
No Transfer, 
Memory 
Overwrite If the internal memory or the SD memory card is full, the 
camera deletes the old images, and continues to buffer the 
image.
FTP  The camera transfers the image to an FTP server (see  
page 99).
E-mail  The camera transfers the image by E-mail (see page 101). 

Operating Instructions
99
When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
 Clicking [

Operating Instructions
100
Overwrite 
Setting Selecting [Overwrite File] overwrites the image on the server 
with a newer image. Selecting [Save as New File with Time 
Stamp] saves the image attaching time stamps on the file 
name, and the images are not overwritten.
E.g. image20060101093020500
.jpg
The underlined numbers mean “9h30min20s500ms on 
January 1, 2006”. The letter “s” is inserted after the day when 
referring to a daylight saving time zone.
Data 
Transfer 
Method Select [Passive Mode]...