Panasonic Network Camera Bb Hcm331a Operating Instructions

							Operating Instructions
81[For assistance, please call: 1-800-272-7033]
2.17 Format the SD memory card
Before you record the camera image, you need to format the SD memory card.
Notes
• You can confirm the SD memory capacity on the Status page (see page 
11 0 ) .
1.Insert the SD memory card (see page 34 of the Installation/Troubleshooting).
2.Click [Buffer/Transfer] on the Setup page.
3.Click [Format].
4.Click [OK] on the confirmation window.
• Format is complete.
5.Click [Go to Image Buffer/Transfer page].
• The Image Buffer/Transfer page is displayed. 
						

							Operating Instructions
82
2.18 Stop the SD Memory Recording
After you stop the SD memory recording, remove the SD memory card.
Notes
• You can confirm the SD memory capacity on the Status page (see page 
11 0 ) .
1.Click [Buffer/Transfer] on the Setup page.
2.Click [SD video recording stop].
3.Click [OK] on the confirmation window.
• The SD memory recording is stopped.
4.Click [Go to Image Buffer/Transfer page].
• The Image Buffer/Transfer page is displayed.
Notes
• If the camera is restarted (see page 110), the SD memory recording starts 
again.
• If you remove the SD memory card and insert it again, the SD memory 
recording starts again (see page 34 of the Installation/Troubleshooting).
• Ensure that recording has been stopped, before removing the SD memory 
card. If the SD memory card is removed while recording, the image file will 
most likely become unreadable. In this case, format the SD memory card 
again. (Files will be deleted.) 
						

							Operating Instructions
83[For assistance, please call: 1-800-272-7033]
2.19 Buffering or Transferring Images by Timer
The Image Buffer/Transfer page allows you to enable image buffer/transfer by E-
mail or FTP.
Note
If you are recording images to the SD memory card, refresh interval slows 
down.
1.Click [Buffer/Transfer] on the Setup page.
2.Click [No.] to enable buffer/transfer.
3.Check [Enable Image Buffer/Transfer], select [Timer] for trigger, and click 
[Next>].
Note
If you click [Save], all buffered images on the SD memory card are deleted.
• Click [Delete Buffered Images] to delete this buffered images.
• Click [Save] to save the settings.
• Clicking [Cancel] takes you back to the Image Buffer/Transfer page without 
saving changes. 
						

							Operating Instructions
84
4.Set the time, and click [Next>].
Note
The timer works by an internal clock. Set the date and time before using timer 
buffer/transfer (see page 62).
• Clicking [].
• Clicking [
						

							Operating Instructions
85[For assistance, please call: 1-800-272-7033]
6.Set the image buffer frequencies, and click [Next>].
Note
Due to the network environment, object, number of accesses, enabling IPsec, 
SD memory recording, the camera may not record the numbers of images as 
you set. In this case, set the image buffer frequencies longer.
• Clicking [
						

							Operating Instructions
86
7.Select the transfer method, and click [Next>].
• Clicking [
						

							Operating Instructions
87[For assistance, please call: 1-800-272-7033] When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
• Clicking [
						

							Operating Instructions
88
Setting Description
Server IP 
Address or 
Host Name
*1
*1But [Space], ["], ['], [&], [] are not available.
• If you set the server IP address, set 4 digits (0—255) and 3 
periods such as "192.168.0.253". But "0.0.0.0" and 
"255.255.255.255" are not available. Or set a host name (1—
255 characters).
• You can set IPv6 address.
Port No. • Enter the number (1—65535). Usually set to 21.
Login ID
*1• If your ISP requires a login ID, set it (0—63 characters).
Password
*1• If your ISP requires a password, set it (0—63 characters).
Login Timing • Select the login timing to an FTP server. If you set [One Time] 
during 1-minute transfer, the camera logs in to the server only 
once, and can reduce the time to log in or log out.
Upload File 
Name
*1• Set the file name to save on an FTP server. Enter 1—234 
characters. Entering "\" creates directories for a file. (E.g. 
NetworkCamera\image.jpg)
Overwrite 
Setting• Selecting [Overwrite File] saves and overwrites the image on 
the server. Selecting [Save as New File with Time Stamp] 
saves the image attaching time stamps on the file name, and 
the images are not overwritten.
Data 
Transfer 
Method• Select [Passive Mode] normally. If FTP does not work, select 
[Active Mode] and check the operation. 
						

							Operating Instructions
89[For assistance, please call: 1-800-272-7033] When you set [E-mail] for Transfer Method
Select [E-mail], and click [Next>]. The following page is displayed.
• Clicking [
						

							Operating Instructions
90
Setting Description
SMTP Server IP 
Address or Host 
Name• If you set the server IP address, set 4 digits (0—255) and 
3 periods such as "192.168.0.253". But "0.0.0.0" and 
"255.255.255.255" are not available. Or set a host name 
(1—255 characters).
• You can set IPv6 address.
POP3 Server IP 
Address or Host 
Name• If you set the server IP address, set 4 digits (0—255) and 
3 periods such as "192.168.0.253". But "0.0.0.0" and 
"255.255.255.255" are not available. Or set a host name 
(1—255 characters).
• You can set IPv6 address.
Login ID
*1
*1But [Space], ["], ['], [&], [] are not available.
• If your ISP requires a login ID to log in to a POP3 server, 
set it (0—63 characters).
Password
*1• If your ISP requires a password to log in to a POP3 server, 
set it (0—63 characters).
Reply E-mail 
Address
*1• Set the sender's E-mail address. We recommend you to 
set the administrator's E-mail address.
Destination E-
mail Address
*1 
1—3• Set the destination E-mail address (up to 3).
Subject • Enter a subject with ASCII characters (see page 140) or 
characters in each language (0—44 characters for a 1-
byte character and 0—22 characters for a 2-byte 
character). But ["] is not available.
Text • Enter text with ASCII characters (see page 140) or 
characters in each language (0—63 characters for a 1-
byte character and 0—31 characters for a 2-byte 
character). But ["] and [end-of-line] key are not available.