Panasonic Network Camera Bb Hcm331a Operating Instructions

							Operating Instructions
91[For assistance, please call: 1-800-272-7033]
8.Confirm the settings, and click [Save].
• New settings are saved.
• When finished, "Success!" is displayed.
9.Click [Go to Image Buffer/Transfer page].
• The Image Buffer/Transfer page is displayed.
Notes
• If you click [Save] on the Image Buffer/Transfer page, all buffered images 
on the SD memory card are deleted.
• If you are buffering images on the internal memory, the following 
operations also delete all buffered images.
• Turning off the camera.
• Saving the Date and Time page.
• Restarting, updating firmware or resetting the camera to factory 
default. 
						

							Operating Instructions
92
2.20 Buffering or Transferring Images by Alarm 
Signal
The Image Buffer/Transfer page allows you to enable image buffer/transfer by E-
mail or FTP.
Note
If you are recording images to the SD memory card, refresh interval slows 
down.
1.Click [Buffer/Transfer] on the Setup page.
2.Click [No.] to enable buffer/transfer.
3.Check [Enable Image Buffer/Transfer], select [Alarm 1 or 2] for trigger, select 
[Rising: GND to Open (High).] or [Falling: Open (High) to GND.] and click 
[Next>].
Note
If you click [Save], all buffered images on the SD memory card are deleted.
• Click [Delete Buffered Images] to delete this buffered images.
• Click [Save] to save the settings.
• Clicking [Cancel] takes you back to the Image Buffer/Transfer page without 
saving changes. 
						

							Operating Instructions
93[For assistance, please call: 1-800-272-7033]
4.Set the time, and click [Next>].
Note
The timer works by an internal clock. Set the date and time before using timer 
buffer/transfer (see page 62).
• Clicking [
						

							Operating Instructions
94
5.Set the Lens Position When Triggered setting, and click [Next>].
Note
If you enable the Lens Position When Triggered setting, buffer/transfer starts 
after the camera turns to the alarm position.
• Clicking [].
• Clicking [
						

							Operating Instructions
95[For assistance, please call: 1-800-272-7033]
7.Set the image buffer frequencies, and click [Next>].
Note
Due to the network environment, object, number of accesses, enabling IPsec, 
SD memory recording, the camera may not record the numbers of images as 
you set. In this case, set the image buffer frequencies longer. For the SD 
memory recording, 1 image per second setting is recommended.
• Clicking [
						

							Operating Instructions
96
8.Select the transfer method, and click [Next>].
• Clicking [
						

							Operating Instructions
97[For assistance, please call: 1-800-272-7033] When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
• Clicking [
						

							Operating Instructions
98
Setting Description
Server IP 
Address or 
Host Name
*1
*1But [Space], ["], ['], [&], [] are not available.
• If you set the server IP address, set 4 digits (0—255) and 3 
periods such as "192.168.0.253". But "0.0.0.0" and 
"255.255.255.255" are not available. Or set a host name (1—
255 characters).
• You can set IPv6 address.
Port No. • Enter the number (1—65535). Usually set to 21.
Login ID
*1• If your ISP requires a login ID, set it (0—63 characters).
Password
*1• If your ISP requires a password, set it (0—63 characters).
Login Timing • Select the login timing to an FTP server. If you set [One Time] 
during 1-minute transfer, the camera logs in to the server only 
once, and can reduce the time to log in or log out.
Upload File 
Name
*1• Set the file name to save on an FTP server. Enter 1—234 
characters. Entering "\" creates directories for a file. (E.g. 
NetworkCamera\image.jpg)
Overwrite 
Setting• Selecting [Overwrite File] saves and overwrites the image on 
the server. Selecting [Save as New File with Time Stamp] 
saves the image attaching time stamps on the file name, and 
the images are not overwritten.
Data 
Transfer 
Method• Select [Passive Mode] normally. If FTP does not work, select 
[Active Mode] and check the operation. 
						

							Operating Instructions
99[For assistance, please call: 1-800-272-7033] When you set [E-mail] for Transfer Method
Select [E-mail], and click [Next>]. The following page is displayed.
• Clicking [
						

							Operating Instructions
100
Setting Description
SMTP Server IP 
Address or Host 
Name• If you set the server IP address, set 4 digits (0—255) and 
3 periods such as "192.168.0.253". But "0.0.0.0" and 
"255.255.255.255" are not available. Or set a host name 
(1—255 characters).
• You can set IPv6 address.
POP3 Server IP 
Address or Host 
Name• If you set the server IP address, set 4 digits (0—255) and 
3 periods such as "192.168.0.253". But "0.0.0.0" and 
"255.255.255.255" are not available. Or set a host name 
(1—255 characters).
• You can set IPv6 address.
Login ID
*1
*1But [Space], ["], ['], [&], [] are not available.
• If your ISP requires a login ID to log in to a POP3 server, 
set it (0—63 characters).
Password
*1• If your ISP requires a password to log in to a POP3 server, 
set it (0—63 characters).
Reply E-mail 
Address
*1• Set the sender's E-mail address. We recommend you to 
set the administrator's E-mail address.
Destination E-
mail Address
*1 
1—3• Set the destination E-mail address (up to 3).
Subject • Enter a subject with ASCII characters (see page 140) or 
characters in each language (0—44 characters for a 1-
byte character and 0—22 characters for a 2-byte 
character). But ["] is not available.
Text • Enter text with ASCII characters (see page 140) or 
characters in each language (0—63 characters for a 1-
byte character and 0—31 characters for a 2-byte 
character). But ["] and [end-of-line] key are not available.