Panasonic Network Camera Bb Hcm331a Operating Instructions
Have a look at the manual Panasonic Network Camera Bb Hcm331a Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 46
Operating Instructions
46
5.Click [Restart].
• The camera restarts, and the Top page is displayed.
Notes
• When you do not know the camera IP address while setting [Automatic
Setup], you can search it by using the Setup Program (see page 133). Or
you can search it on the Status page (see page 110) after accessing the
camera in IPv4.
• If the camera is restarted, all buffered images on the internal memory are
deleted. The buffered images on the SD memory card are not deleted.
Setting Description
Allow...](http://img.usermanuals.tech/thumb/58/69502/w64_bb-hcm331a_en_om_d-45.png "Page 46
Operating Instructions
46
5.Click [Restart].
• The camera restarts, and the Top page is displayed.
Notes
• When you do not know the camera IP address while setting [Automatic
Setup], you can search it by using the Setup Program (see page 133). Or
you can search it on the Status page (see page 110) after accessing the
camera in IPv4.
• If the camera is restarted, all buffered images on the internal memory are
deleted. The buffered images on the SD memory card are not deleted.
Setting Description
Allow...")
![Page 47
Operating Instructions
47[For assistance, please call: 1-800-272-7033] DNS Server
Address• DNS server address is required in the following conditions.
• Transferring camera images by E-mail or FTP
• Setting cameras by their host names on the Multi-
Camera Setup page
• Using the Viewnetcam.com service
• If you have the assigned DNS server IPv6 addresses by
your ISP or network administrator, enter them in this data
field. They usually have two addresses.
• IPv6 address consists of 8 hexadecimal digits...](http://img.usermanuals.tech/thumb/58/69502/w64_bb-hcm331a_en_om_d-46.png "Page 47
Operating Instructions
47[For assistance, please call: 1-800-272-7033] DNS Server
Address• DNS server address is required in the following conditions.
• Transferring camera images by E-mail or FTP
• Setting cameras by their host names on the Multi-
Camera Setup page
• Using the Viewnetcam.com service
• If you have the assigned DNS server IPv6 addresses by
your ISP or network administrator, enter them in this data
field. They usually have two addresses.
• IPv6 address consists of 8 hexadecimal digits...")
![Page 49
Operating Instructions
49[For assistance, please call: 1-800-272-7033]
IPsec Mode Selection
Select transport mode or tunnel mode to access the camera.
Transport Mode (IPv4 Only)
The image is encrypted in the whole way between the camera and your PC. In the
environment of Windows XP Service Pack 1, transport mode is available only in
IPv4.
Prepare the following requirements.
ItemSupported Feature
PC Operating System
Web Browser
ISP Service: Windows XP Service Pack 1
: Internet Explorer 6.0 or later
:...](http://img.usermanuals.tech/thumb/58/69502/w64_bb-hcm331a_en_om_d-48.png "Page 49
Operating Instructions
49[For assistance, please call: 1-800-272-7033]
IPsec Mode Selection
Select transport mode or tunnel mode to access the camera.
Transport Mode (IPv4 Only)
The image is encrypted in the whole way between the camera and your PC. In the
environment of Windows XP Service Pack 1, transport mode is available only in
IPv4.
Prepare the following requirements.
ItemSupported Feature
PC Operating System
Web Browser
ISP Service: Windows XP Service Pack 1
: Internet Explorer 6.0 or later
:...")
![Page 51
Operating Instructions
51[For assistance, please call: 1-800-272-7033]
2.5 Encrypt the Camera Image in Transport Mode
The camera can encrypt the image using IPsec transport mode.
Note
If you use IPsec, refresh interval slows down.
1.Click [IPsec] on the Setup page.
2.Click Camera in the Transport column.
• If you use transport mode in E-mail or FTP transfer, click No. in the Buffer/
Transfer column.
3.Enter each parameter in the data field.The display shows that
the communication is in
HTTP and any...](http://img.usermanuals.tech/thumb/58/69502/w64_bb-hcm331a_en_om_d-50.png "Page 51
Operating Instructions
51[For assistance, please call: 1-800-272-7033]
2.5 Encrypt the Camera Image in Transport Mode
The camera can encrypt the image using IPsec transport mode.
Note
If you use IPsec, refresh interval slows down.
1.Click [IPsec] on the Setup page.
2.Click Camera in the Transport column.
• If you use transport mode in E-mail or FTP transfer, click No. in the Buffer/
Transfer column.
3.Enter each parameter in the data field.The display shows that
the communication is in
HTTP and any...")
![Page 52
Operating Instructions
52
4.Click [Save] when finished.
• New settings are saved.
5.Click [Cancel].
• The IPsec page is displayed.
6.Check [Use] in the IPsec column, check encoding strength, and click [Save]. Setting Description
Status • Check the box to use this encryption method.
Pre-Shared Key • It is the key to use in the authentication of communications.
Enter the same pre-shared key as your PC.
• Enter ASCII characters for the host name (see page 140).
But [Space], ["], ['], [&], [] are...](http://img.usermanuals.tech/thumb/58/69502/w64_bb-hcm331a_en_om_d-51.png "Page 52
Operating Instructions
52
4.Click [Save] when finished.
• New settings are saved.
5.Click [Cancel].
• The IPsec page is displayed.
6.Check [Use] in the IPsec column, check encoding strength, and click [Save]. Setting Description
Status • Check the box to use this encryption method.
Pre-Shared Key • It is the key to use in the authentication of communications.
Enter the same pre-shared key as your PC.
• Enter ASCII characters for the host name (see page 140).
But [Space], [\"], ['], [&], [] are...")
![Page 53
Operating Instructions
53[For assistance, please call: 1-800-272-7033]
7.Click [Restart].
8.Set up your PC as it fits to the requirements on page 49.
• Set the FTP server or E-mail server to transfer images.
9.Access the camera (see page 12).
• If you can access the camera, the IPsec setup is complete.
Notes
• In IPsec communications, "IPsec" is displayed on the Top page or the
Single Camera page.
• If you cannot communicate using IPsec, see 2.9 IPsec in the
Troubleshooting section of the...](http://img.usermanuals.tech/thumb/58/69502/w64_bb-hcm331a_en_om_d-52.png "Page 53
Operating Instructions
53[For assistance, please call: 1-800-272-7033]
7.Click [Restart].
8.Set up your PC as it fits to the requirements on page 49.
• Set the FTP server or E-mail server to transfer images.
9.Access the camera (see page 12).
• If you can access the camera, the IPsec setup is complete.
Notes
• In IPsec communications, \"IPsec\" is displayed on the Top page or the
Single Camera page.
• If you cannot communicate using IPsec, see 2.9 IPsec in the
Troubleshooting section of the...")
![Page 54
Operating Instructions
54
2.6 Encrypt the Camera Image in Tunnel Mode
The camera can encrypt the image using IPsec tunnel mode.
Notes
• Do not set IPsec on the PCs under the VPN router. Communications may
be blocked.
• If you use IPsec, refresh interval slows down.
• The camera can be accessed only from the PCs under the VPN router.
Other PCs cannot access the camera.
1.Click [IPsec] on the Setup page.
2.Click Add in the Tunnel column.
3.Enter each parameter in the data field.](http://img.usermanuals.tech/thumb/58/69502/w64_bb-hcm331a_en_om_d-53.png "Page 54
Operating Instructions
54
2.6 Encrypt the Camera Image in Tunnel Mode
The camera can encrypt the image using IPsec tunnel mode.
Notes
• Do not set IPsec on the PCs under the VPN router. Communications may
be blocked.
• If you use IPsec, refresh interval slows down.
• The camera can be accessed only from the PCs under the VPN router.
Other PCs cannot access the camera.
1.Click [IPsec] on the Setup page.
2.Click Add in the Tunnel column.
3.Enter each parameter in the data field.")
![Page 55
Operating Instructions
55[For assistance, please call: 1-800-272-7033]
4.Click [Save] when finished.
• New settings are saved.
5.Click [Cancel].
• The IPsec page is displayed.
6.Check [Use] in the IPsec column, check encoding strength, and click [Save]. Setting Description
Status • Check the box to use this encryption method.
Pre-Shared Key • It is the key to use in the authentication of communications.
Enter the same pre-shared key as your VPN router.
• Enter ASCII characters for the host name (see...](http://img.usermanuals.tech/thumb/58/69502/w64_bb-hcm331a_en_om_d-54.png "Page 55
Operating Instructions
55[For assistance, please call: 1-800-272-7033]
4.Click [Save] when finished.
• New settings are saved.
5.Click [Cancel].
• The IPsec page is displayed.
6.Check [Use] in the IPsec column, check encoding strength, and click [Save]. Setting Description
Status • Check the box to use this encryption method.
Pre-Shared Key • It is the key to use in the authentication of communications.
Enter the same pre-shared key as your VPN router.
• Enter ASCII characters for the host name (see...")
![Page 56
Operating Instructions
56
7.Click [Restart].
8.Set up your VPN router as shown below.
• To use tunnel mode, you need to set up your VPN router. Setting Description
IPsec • Check the box to enable IPsec features. If you clear the
box, whole IPsec features will be invalid.
Encoding strength • Encoding strength for IPsec can be selected. If you select
[Standard], DES or NULL is valid as an algorithm, and then
the data will become easier to be decrypted.
IKE Items Settings
Phase 1 Authentication...](http://img.usermanuals.tech/thumb/58/69502/w64_bb-hcm331a_en_om_d-55.png "Page 56
Operating Instructions
56
7.Click [Restart].
8.Set up your VPN router as shown below.
• To use tunnel mode, you need to set up your VPN router. Setting Description
IPsec • Check the box to enable IPsec features. If you clear the
box, whole IPsec features will be invalid.
Encoding strength • Encoding strength for IPsec can be selected. If you select
[Standard], DES or NULL is valid as an algorithm, and then
the data will become easier to be decrypted.
IKE Items Settings
Phase 1 Authentication...")
Operating Instructions 51[For assistance, please call: 1-800-272-7033] 2.5 Encrypt the Camera Image in Transport Mode The camera can encrypt the image using IPsec transport mode. Note If you use IPsec, refresh interval slows down. 1.Click [IPsec] on the Setup page. 2.Click Camera in the Transport column. • If you use transport mode in E-mail or FTP transfer, click No. in the Buffer/ Transfer column. 3.Enter each parameter in the data field.The display shows that the communication is in HTTP and any people can access the camera if they have the pre-shared key. Set up these settings to transfer images in transport mode (see page 103).
Operating Instructions 52 4.Click [Save] when finished. • New settings are saved. 5.Click [Cancel]. • The IPsec page is displayed. 6.Check [Use] in the IPsec column, check encoding strength, and click [Save]. Setting Description Status • Check the box to use this encryption method. Pre-Shared Key • It is the key to use in the authentication of communications. Enter the same pre-shared key as your PC. • Enter ASCII characters for the host name (see page 140). But [Space], ["], ['], [&], [] are not available. Note If the pre-shared key leaks to a third party, it may lead to illegal access, private information leak or interference. To protect your security and privacy, pay attention to the following points. • Make it known only to the specified people. • Set it as many characters as possible. • Change the password regularly. Setting Description IPsec • Check the box to enable IPsec features. If you clear the box, whole IPsec features will be invalid. Encoding strength • Encoding strength for IPsec can be selected. If you select [Standard], DES or NULL is valid as an algorithm, and then the data will become easier to be decrypted.
Operating Instructions 53[For assistance, please call: 1-800-272-7033] 7.Click [Restart]. 8.Set up your PC as it fits to the requirements on page 49. • Set the FTP server or E-mail server to transfer images. 9.Access the camera (see page 12). • If you can access the camera, the IPsec setup is complete. Notes • In IPsec communications, "IPsec" is displayed on the Top page or the Single Camera page. • If you cannot communicate using IPsec, see 2.9 IPsec in the Troubleshooting section of the Installation/Troubleshooting. • See the Panasonic Network Camera support website at http://panasonic.co.jp/pcc/products/en/netwkcam/ for the IPsec features.
Operating Instructions 54 2.6 Encrypt the Camera Image in Tunnel Mode The camera can encrypt the image using IPsec tunnel mode. Notes • Do not set IPsec on the PCs under the VPN router. Communications may be blocked. • If you use IPsec, refresh interval slows down. • The camera can be accessed only from the PCs under the VPN router. Other PCs cannot access the camera. 1.Click [IPsec] on the Setup page. 2.Click Add in the Tunnel column. 3.Enter each parameter in the data field.
Operating Instructions 55[For assistance, please call: 1-800-272-7033] 4.Click [Save] when finished. • New settings are saved. 5.Click [Cancel]. • The IPsec page is displayed. 6.Check [Use] in the IPsec column, check encoding strength, and click [Save]. Setting Description Status • Check the box to use this encryption method. Pre-Shared Key • It is the key to use in the authentication of communications. Enter the same pre-shared key as your VPN router. • Enter ASCII characters for the host name (see page 140). But [Space], ["], ['], [&], [] are not available. Note If the pre-shared key leaks to a third party, it may lead to illegal access, private information leak or interference. To protect your security and privacy, pay attention to the following points. • Make it known only to the specified people. • Set it as many characters as possible. • Change the password regularly. Network address • Enter the destination network address. • Enter "IP address/Prefix length" in the data field. Router address • Enter the WAN IP address of the VPN router on a destination network. Notes • IPv6 link-local address is not available. • The camera can be accessed only from the PCs under the VPN router. Other PCs cannot access the camera.
Operating Instructions 56 7.Click [Restart]. 8.Set up your VPN router as shown below. • To use tunnel mode, you need to set up your VPN router. Setting Description IPsec • Check the box to enable IPsec features. If you clear the box, whole IPsec features will be invalid. Encoding strength • Encoding strength for IPsec can be selected. If you select [Standard], DES or NULL is valid as an algorithm, and then the data will become easier to be decrypted. IKE Items Settings Phase 1 Authentication MethodPre-shared Key Method ID Specifies by address. Mode Main mode *1 Diffie-Hellman MODP GroupSpecifies 1 or 2. Cipher Algorithm Select from DES-CBC, 3DES-CBC or AES-CBC (128, 192, 256 bits). (Multiple selections are available.) Message-Digest AlgorithmHMAC-MD5, HMAC-SHA-1 Lifetime Specifies by 28800 s (Byte setting is not supported.)
Operating Instructions 57[For assistance, please call: 1-800-272-7033] • Set up the IPsec policy as the following. 9.Access the camera (see page 12). • If you can access the camera, the IPsec setup is complete. Notes • In IPsec communications, "IPsec" is displayed on the Top page or the Single Camera page. • If you cannot communicate using IPsec, see 2.9 IPsec in the Troubleshooting section of the Installation/Troubleshooting. • See the Panasonic Network Camera support website at http://panasonic.co.jp/pcc/products/en/netwkcam/ for the IPsec features. Phase 2 Mode Quick mode PFS Specifies either of Off, D-H Group 1 or D- H Group 2. Cipher Algorithm Select from DES-CBC, 3DES-CBC, AES-CBC (128, 192, 256 bits) or NULL. (Multiple selections are available.) Message-Digest AlgorithmHMAC-MD5-96, HMAC-SHA-1-96 Lifetime Specifies by 28800 s (Byte setting is not supported.) *1The camera does not support aggressive mode. Items Settings Protocol ANY Source Network Network address and subnet mask on the LAN side of the VPN router Source IP address A global address on the WAN side of the VPN router Destination Network A global address of the camera Destination IP address A global address of the cameraIKE Items Settings
Operating Instructions 58 2.7 Using UPnP™ (Universal Plug and Play) UPnPTM can automatically configure your router to be accessed from the Internet. In order to use this feature, your router needs to support this feature and it must be enabled. Most router manufacturers disable this feature as the default setting. See http://panasonic.co.jp/pcc/products/en/netwkcam/technic/rtr_setup/ for details and see your router manual for how to enable UPnP TM. After the UPnPTM is enabled on the router, set [Enable] for auto port forwarding. Note The camera's UPnPTM does not support IPv6. Use this feature in IPv4. 1.Click [UPnP] on the Setup page. 2.Set up UPnP. Setting Description Auto Port Forwarding• If the network setting is [Static] or [DHCP], enabling auto port forwarding allows you to access the camera from the Internet. Note If the network setting is [Automatic Setup], enable [Allow Access from the Internet] on the Network page (see page 42). Display Shortcut Icon in My Network Places• Enabling it displays a shortcut to the camera in the My Network Places folder. Note If you use Windows XP or Windows Me, this feature is available. Enable UPnPTM Windows component before using this feature (see page 139).
Operating Instructions 59[For assistance, please call: 1-800-272-7033] 3.Click [Save] when finished. • New settings are saved. • When finished, "Success!" is displayed. 4.Click [Go to UPnP page]. • The UPnP page is displayed.
Operating Instructions 60 2.8 Registering with the Viewnetcam.com service Viewnetcam.com is a free service (dynamic DNS service) that allows you to assign an easy to remember name to the camera, similar to your favorite web site. Viewnetcam.com also allows you to easily access the camera, even when your ISP changes the IP address. Panasonic Communications recommends you to register with it for the Internet access to the camera. See http://www.viewnetcam.com f o r details about the Viewnetcam.com service. 1.Click [Viewnetcam.com] on the Setup page. 2.Check [Enable]. • Clicking [Cancel] cancels your settings without saving changes. 3.Click [Save] when finished. • New settings are saved. • When finished, "Success!" is displayed. 4.Click [Go to Viewnetcam.com page]. • The Viewnetcam.com page is displayed. 5.Click [Your Account Link]. • The Viewnetcam.com registration website is displayed.Setting Description Enable • Check [Enable] to register with the Viewnetcam.com service. If you clear the box, the Viewnetcam.com service stops. Personal (Camera) URL• The camera's personal URL will be displayed after you register with the Viewnetcam.com service. Your Account Link• T h e U R L i s d i s p l a y e d t o r e g i s t e r w i t h t h e V i e w n e t c a m . c o m service. Clicking [Your Account Link] item name displays the Viewnetcam.com registration website.