Panasonic Network Camera Bb Hce481a Operating Instructions

							Operating Instructions
151
4.Click [Save] when finished.
 The new settings are saved.
 The Operation Time page is displayed.
About Operation Time
In the operation time settings, the enabled settings take priority over the disabled 
settings. Therefore, if Monday or Tuesday is disabled in a setting but enabled in 
other settings, the camera can be operated on both Monday and Tuesday.Setting Description
Enable  Check the box to enable the setting. Uncheck the box to 
disable it.
Day of the week  Check the box to enable the day. Uncheck the box to 
disable it.
Operation Time  To set an operation time, check the time option and set a 
time period. Check the [Always] option if you are not 
specifying a time period. 
						

							Operating Instructions
152
5.4 Controlling External Output
The external output terminal allows you to control the external devices. You can 
also change the initial status of the output signal.
1.Click [External Output] on the Setup page.
2.Click [Save] when finished.
 Clicking [Cancel] cancels your settings without saving changes.
 The new settings are saved.
 When finished, Success! is displayed. 
3.Click [Go to External Output Control page].
 The External Output Control page is displayed.Setting Description
External Device 
Control Output If you check [Open], the internal transistor turns off and the 
external output terminal gets high impedance (open 
collector) when the camera powers up. If you check [Short 
to GND], the internal transistor turns on and is electrically 
short-circuited to GND pin when the camera powers up. 
The external output terminal gets low impedance (0 V). 
Button name 
modification You can change the output control button names on the 
operation bar. You can name the button depending on your 
external devices. 
						

							Operating Instructions
153
5.5 Changing the Indicator Display
The Indicator Control page allows you to select an operation for the indicator. 
There are three options.
Always on
 Turn the indicator on when the camera is accessed.
Always off
1.Click [Indicator Control] on the Setup page.
2.Select an option.
 To turn indicator always on, check [Turn indicator on when camera is on] 
(see page 8 [BB-HCM381A] or page 10 [BB-HCE481A]).
 To turn indicator when the camera is accessed, check [Turn indicator on 
during camera access].
 To turn indicator always off, check [Never turn indicator on].
 Clicking [Cancel] cancels your settings without saving changes.
Note
 Selecting [Never turn indicator on] keeps indicator always off even if the 
camera is connected to a network.
3.Click [Save] when finished.
 The new settings are saved.
 When finished, Success! is displayed. 
4.Click [Go to Indicator Control page].
 The Indicator Control page is displayed. 
						

							Operating Instructions
154
6 Camera Maintenance
6.1 Maintenance page
Maintenance
(1) StatusDisplays the camera settings and status (see page 
155).
(2) Session StatusDisplays information on access to the camera (see 
page 155).
(3) Alarm LogDisplays alarm logs (see page 156).
(4) RestartRestarts the camera (see page 157).
(5) Update FirmwareUpdates the camera firmware (see page 158).
(6) Save SettingsCreates a configuration file (see page 160).
(7) Load SettingsLoads settings from a configuration file (see page 
161).
(8) Reset to Factory 
DefaultResets the camera to its default settings (see page 
162).
Maintenance
Session Status
Load Settings
Reset to Factory Default
Alarm Log
Restart
Update Firmware
Save Settings Status
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8) 
						

							Operating Instructions
155
6.1.1 Confirming the Status
The Status page allows you to check the status of the camera. The status 
information provides support for troubleshooting.
Clicking [Status] displays the following page.
Note
 See the Panasonic Network Camera support website at http://
panasonic.co.jp/pcc/products/en/netwkcam/ for details about status 
information.
6.1.2 Confirming Session Status
Displays the information of clients connected to the camera.
Clicking [Session Status] displays the following page. 
						

							Operating Instructions
156
6.1.3 Confirming Alarm Logs
Displays up to 50 Alarm Logs in chronological order. Old logs will be overwritten by 
new ones.
1.Click [Alarm Log] on the Maintenance page.
2.Alarm Logs are displayed.
Note
 If the camera is restarted, all alarm logs are deleted.
Item Description
New Alarm Logs  Displays the number of new alarm logs.
Date  Displays the date and time when the Alarm 1, 2, or 
Motion Detection were activated.
Sensor Type  Displays the Trigger Setting (Alarm 1, 2, or Motion 
Detection) on the Trigger page.
Signal Type  Displays the Alarm enable condition on the Trigger 
page when selected Alarm 1 or 2. 
						

							Operating Instructions
157
6.1.4 Restarting the Camera
It is possible to restart the camera by turning the camera off and turning the camera 
on again. The camera can also be restarted on the Restart page.
Note
 When the camera is restarted, the buffered images will be deleted. The 
buffered images on the SD memory card are not deleted. 
 If the camera is restarted, all alarm logs are deleted.
1.Click [Restart] on the Maintenance page.
2.Click [Restar t].
 Restarting takes about 1 minute. The Top page is displayed when finished. 
						

							Operating Instructions
158
6.1.5 Updating the Camera Firmware
The Update Firmware page allows you to update the camera’s firmware. If new 
firmware is available, install it into the camera.
Note
 Do not turn off the power during a firmware update.
 All buffered images on the internal memory will be deleted after the firmware 
update. The buffered images on the SD memory card are not deleted.
 The firmware version is displayed on the Top page and the Status page.
 If the cameras firmware is updated, all alarm logs are deleted.
1.Download the new firmware from the Panasonic Network Camera support 
website at http://panasonic.co.jp/pcc/products/en/netwkcam/, and save it 
on your PC.
2.Click [Update Firmware] on the Maintenance page.
3.Click [Update Firmware].
 The camera restarts.
 The Update page is displayed after about 1 minute. 
						

							Operating Instructions
159
4.Click [Browse...].
 A dialog box is displayed to select the firmware.
5.Select the firmware (including directory information) and click [Open].
 The firmware file name is displayed.
6.Confirm the firmware file name, and click [Update Firmware].
 Clicking [Cancel] takes you back to the Top page without updating the 
firmware.
 The following message is displayed during the update.
 The camera restarts automatically after the update.
 The Top page is displayed after about 1 minute.
7.Confirm that the version number on the Top page is updated.
 If the version number is updated, the firmware update is complete.Updated version 
						

							Operating Instructions
160
6.1.6 Creating the Configuration File
A configuration file can be saved on your PC. You can load camera settings from 
the configuration file on the Load Settings page (see page 161).
Note
 The saved image contains private information. It is important to prevent leaks 
of private information.
1.Click [Save Settings] on the Maintenance page.
2.Click [Save].
3.Click [Save] on the File Download dialog box.
4.Specify the location, and click [Save] on the Save As dialog box.
 The configuration file is saved at that location.
Note
 The file extension (.dat) cannot be changed. If you change it, the settings 
cannot be loaded.
 If you try to updating the camera, create a configuration file after updating 
the firmware. If there is a firmware version difference between the camera 
that you create a configuration file from and the camera that you try to load 
settings to, the settings may not have been loaded to the camera.