Panasonic Multimedia Projection Hdtv Pt 56dlx76 Operating Instructions

11
Getting Start ed
Vent
Notes:
• Make sure the vents are not blocked. (This could cause damage.)
• Indication on the back panel may change without notice.
Vent
Rear View 
13 5 7 9 11 12
2 4 6 8 10 15 16 191314 17 18
20
1S-Video/Video Input 
Connector 1Connect from other 
component. (Video 1)
2Audio Input 
Connector 1Connect from other 
component. (Video 1)
3S-Video/Video Input 
Connector 2Connect from other 
component. (Video 2)
4Audio Input 
Connector 2Connect from other 
component. (Video 2)
5Video...

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo12
Antenna Connection 
VHF/UHF Cable In terminal on the 
back of the Projection Display
Connecting the Antenna / Cable to the RF IN Terminal
When using “Nut type” RF coaxial cable, tighten with fingers only. Overtightening may damage terminal.
• Turn off the power supply for all com po nents before making any connections.
• Read the instruction manual for each system component care...

13
Getting Start edFor proper reception of analog or digital cable channels, a cable service connection is required.
Cable Connection
Connect the cable from the antenna or 
cable system to the VHF/UHF Cable In 
terminal on the back of the Projection 
Display.
Use this confi guration when connecting the projection display to a cable TV system.
Notes:
• Certain cable systems offset some channels to reduce interference or have Premium (scrambled) channels. A cable converter 
box is required for proper...

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo14
  CableCARD™ Connection
This module (also called Point of Deployment (POD) module or Digital Cable Module (DCM)) allows you to 
tune digital and high definition cable channels through the cable antenna. Contact your local cable company 
for information regarding the availability and costs of CableCARD™ related services.
Notes:
• A Digital Cable Subscription is required.
• Do not...

15
Getting Start edHow to connect the “1, 2, 3”  Input Terminals
Connect a  VCR or other peripheral equipment
• Similar connections are available at the INPUT 1, 2, 3 input terminals. (p. 10-11)
Notes:
• Select the desired VIDEO input position by pressing the TV/VIDEO button. (p. 37)
• When connecting video cables, priority is given to the S-Video cable when the S-Video input terminal and the video input 
terminal are connected at the same time.• Similar connections are available at the INPUT 1, 2, 3...

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo16
How to con nect the  COMPONENT VIDEO Input Terminals
Notes:
• Select the desired COMPONENT VIDEO INPUT position by pressing the TV/VIDEO button. (p. 37)
• Component video signals that will be recognized are 480i, 480p, 720p, and 1080i.
Because each  Y, PB, and PR signal is input independently, the Component signal allows for more accurate 
color reproduction.
The Component signal...

17
Getting Start edHow to connect the AV OUT Terminals
Recording Equipment
(S-VHS /VHS VCR)
VIDEO
AUDIO You can connect a  VCR to the AV OUT terminal to record the program you are viewing on-screen. An 
external monitor can also be connected to the AV OUT terminals. Connect the VCR as shown below.
Notes:
• This unit contains Video and Audio Outputs for the purpose of recording television programming to VCR. Due to license 
restrictions, if a device (STB, DVD, etc.) is connected to the HDMI input of the...

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo18
Installation (continued)
How to connect the Amplifier
Analog Audio Out
 Stereo  System 
(A Stereo Amplifier and Speakers) 
AUDIO To listen to the audio through a separate stereo system, connect an external audio amplifier to AUDIO OUT 
on back of unit.
Note:
• AUDIO OUT terminals cannot be connected directly to external speakers.
Audio Adjustments
• Select Speakers Off in Other...

19
Getting Start edUse the diagram below to connect the Digital  Audio Output of your Projection Display to a Dolby Digital 
decoder.
  Dolby Digital 5.1 channel surround sound delivers digital-quality sound. Dolby Digital provides five discrete 
full-bandwidth channels for front left, front right, center, surround left and surround right, plus a LFE (Low Frequency 
Effect) subwoofer channel. For a full Home Theater sound experience, an external Dolby Digital decoder and a 
multichannel amplifier must be...

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo20
Installation (continued)
IR Blaster Connection
IR Blaster (Supplied)
Infrared emitter
Video recorder (VCR)
The Projection Display converts 
scheduling data displayed on the TV to a 
remote control signal and sends it
(VCR)
No need to set recording time or 
channel on the video recorder Setting of the recording time, 
channel, recording mode, etc.
The TV acts as a proxy for some...