Panasonic Multimedia Projection Display Pt 43lc14 Operating Instructions

31
Basic Operation
  Auto shut off
To extend lamp life, if there is no signal to the set’s tuner for 5 minutes, the lamp will shut off automatically.
Aspect types 
(P. 32)
Receivable 
broad cast  types 
(P. 37)Channel
Channel 
caption 
(P. 53)  TV status display
Using the  Number keys
Example 1: To select channel 125, fi 
rst press the 1 key, then 2, then 5. When selecting CABLE channels 100 to 125 with the Number keys, fi 
rst press the 1 key, 
and then enter the remaining two digits. Press the RECALL...

32For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
The color monitor will allow you to enjoy viewing the picture at its maximum size, including wide screen 
cinema format picture.
The aspect mode changes each time the  ASPECT 
button is pressed.
Notes:
•   When a 1080i or 720p signal is being received, the mode is set to FULL, and 
aspect switching is not possible.
)8//
Notes:
•   However, if the mode selected does not match the...

33
Basic Operation
Note:
•   The screen size changes if ID1 is detected. (P. 58)
ASPECT Controls
Mode Picture Ex pla na tion
NORMAL
1250$/
 
NORMAL will display a 4:3 picture at its 
stand ard 4:3 size.
JUST
-867
 
JUST mode will display a 4:3 picture at 
max i mum size but with aspect correction 
applied to the center of the screen so that 
elongation is only apparent at the left and 
right edges of the screen. The size of the 
picture will depend on the original signal.
ZOOM
=220


ZOOM mode...

34For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
When the SEARCH/OPEN/CLOSE button is pressed 
during single screen.
When a channel button is pressed during channel 
search.
Sound from the left screen is 
output from the speakers on the 
projection display set. Channel search displays each channel, in order, as a paused image. Channels are dis played from the left top 
to the right bottom in order. When it reaches the right...

35
Basic Operation
VC R
DV D pl aye r
This equipment can 
also be con nect ed to 
the rear terminals. See 
Connections for details.
Turning the power on and switching input modes
Turn the projection 
display on.
1
2
  The input mode changes 
each time this button is 
pressed.
*   If SKIP is set as the Input 
Label setting of SETUP, the 
mode will not be changed. 
(P. 52)
3Operate the connected equipment.
Confi 
rming connections
A video camera uses the Input 3 terminal on the front of the projection...

36For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Press this button to mute the sound. Press again to 
reactivate sound. Sound is also reactivated when power 
is turned off or volume level is changed.
Projection can be switched between a frozen (still) 
picture and a moving picture each time the FREEZE 
button on the Remote Control unit is pressed. Press 
FREEZE button again to resume motion.
  Sound mute
Useful when answering the...

37
Basic Operation
The following are possible broadcast types with their accompanying on-screen displays. The signal being 
received is indicated with a “ 
   ” mark while the se lect ed audio mode is indicated with an arrow. To change the 
audio mode for these broadcasts, fol low the “Select Audio Mode for TV Viewing” sec tion (be low.)
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main lan guage) and Secondary 
Au dio Program (sub lan guage) broad casts are both be ing received...

38For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Notes:
•   Sound from the Left screen is output from the speakers on the projection 
display set.
•   When the screen is split, signals of the Left screen are output from the rear 
monitor output terminal.
•   The left and right screens are processed by individual circuits and, 
therefore, may vary in image quality.
•   Split screen returns to single screen when the projection...

39
Basic Operation
Swapping left and right screens
Example:
During SPLIT SCREEN NORMAL
&+&+
Changing the channel of the right screen
&+
Press to swap.
Example:
During SPLIT SCREEN NORMAL
Note:
•   When outside input is fi 
nished, the low est reg is tered 
chan nel number is displayed. For fast er selection, 
press the SWAP but ton to change the screen to the left. 
Then, press the TV/VIDEO but ton to directly change 
the input. Finally, press SWAP button again to change 
the screen back to the...

40For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
5
Press the MENU button to display the MENU screen.
Press to select 
OTHER.
Press to display 
OTHER screen.
Press to set or adjust 
to desired level.
(See next page.)2
4
Press to select the screen mode.1
RGB input
ZOOM modeNOR MAL mode JUST mode
Press to exit menu.Press to select 
each item.
Note:
•   NORMAL is displayed at default.
Adjusting screen position and size
3,&785(
$8,2...