Panasonic Multimedia Projection Display Pt 43lc14 Operating Instructions

21
Getting Start ed
By inputting a High-bandwidth Digital Content Protection high-defi 
nition picture source to the HDMI IN terminal of 
this Device Display, high-defi 
nition pictures can be displayed on the screen in their digital form. (This terminal is for 
use in the future when High-bandwidth Digital Content Protection DVD players and D-VHS are put on the market.)
Notes:
•   Select the HDMI input position by pressing the TV/VIDEO button. (P. 35)
•   The HDMI IN terminal can only be used with 1080i,...

22For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Always be sure to follow the procedure given below to turn the projection display power ON and OFF.
•   The lamp cooling fan will continue to operate for approximately 1 minute after the power is turned off. At the same time, the 
POWER indicator will blink Red.
Press  POWER on projection display or Remote Control 
to turn power on.
The Power Indicator blinks Green for about 10...

23
Basic Operation
Power ON / OFF
In order to view TV or Cable programs, it is necessary to perform channel setting.
If needed, follow the menus and procedures displayed on-screen for setting up the features.
Input Setup
To select the confi 
guration of RF input depending on the signal source.
Procedure
Press OK to select Cable or TV.
Press ► to next.
Press OK to start the Auto Scan.
Notes:
•   To cancel AUTO SET in progress, press the EXIT 
button.
•   If setup is incomplete, check connection of...

24For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Pressing the  MENU 
button displays the 
MENU screen.
Note:
•   Depending on the signal 
being input, some items 
may or may not be 
adjustable and some 
functions may or may not 
be available.
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA...

25
Basic Operation
Basic Menu Navigation
Continued from page 24.
Pressto adjust or set desired 
menu item.
COLOR +32
Note: For OTHER ADJUST sub-menu
Pressto select OTHER 
ADJUST.
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
3,&02(9,9,
&2/25
7,17
%5,*+71(66
3,&785(
6+$531(66
1250$/
27+(5$-867*8,(
6(/(&7
6(7
0(18(;,7
Pressto access OTHER 
ADJUST sub-menu.
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
&2/257(031250$/...

26For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Automatically searches and adds receivable channels to memory.
Press the MENU button to display the MENU screen.
Press to select 
CHANNEL.
Press to display 
the CHANNEL 
screen.
Press to select 
TV or CABLE. Press to select 
ANTENNA.
Press to select 
AUTO SET.
Press to run 
AUTO SET.
Note:
•   TV or Cable Tuning mode must be set according to your connections.
1
2
3
Channels will...

27
Basic Operation
Notes:
•   After AUTO SET is fi 
nished, the lowest channel number added will be received.
•   Some channels with very weak signals may be locked into memory. If desired, these channels can be deleted man u al ly using 
the MANUAL SET feature.
4 Case 1
 Case 2 When setup is complete, the lowest channel picture appears.
If setup is incomplete, the screen at right appears. Check 
connection of Antenna/Cable to the RF in Terminal, then try 
Automatic Channel Setting again.
Press to exit...

28For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Use this setting when changing setting of receiving channels or changing the channel dis play.
3
Press to select 
MANUAL SET.
Press to display 
the MANUAL SET 
screen. Press the MENU button to display the MENU screen.
Press to select 
CHANNEL.
Press to display 
the CHANNEL 
screen.
Press to select 
TV or CABLE.Press to select 
ANTENNA.
1
2
Manual channel setting
Continued on the...

29
Basic Operation
4
Press to select channel.
Repeat step 4 to continue adding or deleting channels.Press to add channels to memory.
Press to select channel.
Press to delete channels from memory.
Press to exit menu.
Note:
•   Some channels with very weak signals may be locked into memory. If desired, these channels can be deleted manually using 
the MANUAL SET feature.
5
6
To add channel
To delete channel
Tu n i n g  c h a n n e l s  
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
0$18$/6(7...

30For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Operation can be done from the projection display.
Press to 
select the 
desired 
volume 
level. Press to select the desired 
channel. (Or use Number keys ) Press to turn the projection display on. Press to operate the projection 
display with the Remote Control.
1
2
3
4
Notes:
•   The channel number and volume level are stored even after the projection display is turned off.
•...