Panasonic Multimedia Projection Display Pt 43lc14 Operating Instructions

							21
Getting Start ed
By inputting a High-bandwidth Digital Content Protection high-defi 
nition picture source to the HDMI IN terminal of 
this Device Display, high-defi 
nition pictures can be displayed on the screen in their digital form. (This terminal is for 
use in the future when High-bandwidth Digital Content Protection DVD players and D-VHS are put on the market.)
Notes:
•   Select the HDMI input position by pressing the TV/VIDEO button. (P. 35)
•   The HDMI IN terminal can only be used with 1080i, 720p and 480p picture signals.
•   If there is no audio, check if the source equipment has PCM output. If not, please use analog connections.
•   Be sure HDMI is securely connected. If not, picture noise and/or incorrect picture display may result.
Procedure
Audio signal ( PCM)
Video Signal:
The Device display is compatible with following formats. Please set the connecting device to following format.
Display mode No. of dots Vertical scanning frequency (Hz)
  1080i 1920 x 1080i 59.94 / 60
  720p 1280 x 720p 59.94 / 60
  480p720 x 480p
640 x 480p59.94 / 60
59.94 / 60
•   If you cannot display the picture because your Digital Set Top Box does not have a Digital Out terminal 
setting, use the Component Video Input (or the S-Video Input or Video Input). In this case, the picture will be 
displayed as an analog signal.
Press TV/ VIDEO on the Remote Control to select HDMI input. 
Connect the HDMI output from the set top box or a DVD player to the HDMI input on the back of the unit.
1
2
Compatible formats
Installation
Please see “AUDIO SELECT” on page 43. 
						

							22For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Always be sure to follow the procedure given below to turn the projection display power ON and OFF.
•   The lamp cooling fan will continue to operate for approximately 1 minute after the power is turned off. At the same time, the 
POWER indicator will blink Red.
Press  POWER on projection display or Remote Control 
to turn power on.
The Power Indicator blinks Green for about 10 seconds 
and then turns solid Green.
The Power Indicator
Notes:
•   If the POWER button is accidentally turned off during use, after power is turned back on, it may take a short period before the 
lamp automatically comes on.
•   After the unit is turned on, maximum picture brightness will be achieved in 5-10 minutes. This is normal.
Press POWER on projection display or Remote Control 
to turn power off.
Note:
•   When the AC Cord is unplugged, the internal cooling fan stops op er at ing. In this case, the lamp will be insuffi 
ciently cooled and 
will take a while to turn ON again.
Power ON
Power OFF
The Power Indicator blinks Red for about 1 minute and 
then turns solid Red.
Turning the Power ON and OFF
 POWER  button/
POWER indicator
LED ACTION
Red Power – OFF (Standby mode)
Red blink Power – OFF (Now cooling)
Green Power – ON
Green blink Power – ON (Preparing to light lamp)
POWER
SAP
LIGHT
CH
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
MUTEASPECTBBERECALL
Power shuts off after a Black Screen is displayed for a 
few seconds.
Note:
•   If POWER is pressed during the Black Screen display, Power 
is turned back on.
Do not disconnect the power cord from the outlet and do not open the circuit breaker (unless necessary) 
while the cooling fan is still operating. Do not disconnect the power cord from the power outlet while the 
power indicator blinks Red.
Power ON and OFF 
						

							23
Basic Operation
Power ON / OFF
In order to view TV or Cable programs, it is necessary to perform channel setting.
If needed, follow the menus and procedures displayed on-screen for setting up the features.
Input Setup
To select the confi 
guration of RF input depending on the signal source.
Procedure
Press OK to select Cable or TV.
Press ► to next.
Press OK to start the Auto Scan.
Notes:
•   To cancel AUTO SET in progress, press the EXIT 
button.
•   If setup is incomplete, check connection of 
Antenna/Cable to the RF IN Terminal, then try 
Auto Scan again. (PP. 26-27)
After Auto Scan is completed the unit tunes to 
the fi 
rst channel found during auto scan.
First Time Setup
 Case 1
 Case 2 When setup is complete, the lowest 
channel picture appears.
If setup is incomplete, the following 
screen appears. Check connection of 
Antenna/Cable to the RF in Terminal, 
then try Automatic Channel Setting 
again. (PP. 26-27)
 CH AUTO SET PROCEEDING
      NO CH FOUND
 PLEASE CHECK ANTENNA
 CABLE CONNECTION THEN
 PRESS OK KEY AGAIN
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
$17(11$&$%/(
$8726(7
0$18$/6(7
&+$11(/&$37,21
:($.6,*1$/21*8,(
1(;7
6(7
0(18(;,7
PICTURE
AUDIO
CHANNEL
SETUP
LOCK
OTHER
LANGUAGE-GUIDE-
SET
EXIT
ANTENNA CABLE
AUTO SET
MANUAL SET
CHANNEL CAPTION
WEAK SIGNAL ON
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
OK
MUTEASPECTBBERECALL
6(/(&7/$1*8$*(
(1*/,6+35(66
)5$1d$,6$338
						

							24For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Pressing the  MENU 
button displays the 
MENU screen.
Note:
•   Depending on the signal 
being input, some items 
may or may not be 
adjustable and some 
functions may or may not 
be available.
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
OK
MUTEASPECTBBERECALL
Basic Menu Navigation
12
Pressto select the desired 
menu.
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(*8,(
6(/(&7
6(7
0(18(1
3,&02(9,9,
&2/25
7,17
%5,*+71(66
3,&785(
6+$531(66
1250$/
27+(5$-867
Pressto enter the menu.
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
3,&02(9,9,
&2/25
7,17
%5,*+71(66
3,&785(
6+$531(66
1250$/
27+(5$-867*8,(
6(/(&7
6(7
0(18(;,7
Pressto select desired menu 
item.
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
3,&02(9,9,
&2/25
7,17
%5,*+71(66
3,&785(
6+$531(66
1250$/
27+(5$-867*8,(
6(/(&7
6(7
$-867
0(18(;,7
Continued in left column of next page. 
						

							25
Basic Operation
Basic Menu Navigation
Continued from page 24.
Pressto adjust or set desired 
menu item.
COLOR +32
Note: For OTHER ADJUST sub-menu
Pressto select OTHER 
ADJUST.
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
3,&02(9,9,
&2/25
7,17
%5,*+71(66
3,&785(
6+$531(66
1250$/
27+(5$-867*8,(
6(/(&7
6(7
0(18(;,7
Pressto access OTHER 
ADJUST sub-menu.
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
&2/257(031250$/
9,(21521

						

							26For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Automatically searches and adds receivable channels to memory.
Press the MENU button to display the MENU screen.
Press to select 
CHANNEL.
Press to display 
the CHANNEL 
screen.
Press to select 
TV or CABLE. Press to select 
ANTENNA.
Press to select 
AUTO SET.
Press to run 
AUTO SET.
Note:
•   TV or Cable Tuning mode must be set according to your connections.
1
2
3
Channels will automatically advance until all channels have been 
scanned. Channel numbers with a video signal present will be stored in 
the channel scan memory.
Automatic channel setting
Continued on the next page. Note:
•   To cancel AUTO SET in progress, press 
the EXIT button. CH AUTO SET PROCEEDING
Tu n i n g  c h a n n e l s
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
$17(11$&$%/(
$8726(7
0$18$/6(7
&+$11(/&$37,21
:($.6,*1$/21*8,(
6(/(&7
6(7
0(18(1
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
$17(11$&$%/(
$8726(7
0$18$/6(7
&+$11(/&$37,21
:($.6,*1$/21*8,(
6(/(&7
6(7
0(18(;,7
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
$17(11$&$%/(
$8726(7
0$18$/6(7
&+$11(/&$37,21
:($.6,*1$/21*8,(
6(/(&7
6(7
0(18(;,7
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
OK
MUTEASPECTBBERECALL 
						

							27
Basic Operation
Notes:
•   After AUTO SET is fi 
nished, the lowest channel number added will be received.
•   Some channels with very weak signals may be locked into memory. If desired, these channels can be deleted man u al ly using 
the MANUAL SET feature.
4 Case 1
 Case 2 When setup is complete, the lowest channel picture appears.
If setup is incomplete, the screen at right appears. Check 
connection of Antenna/Cable to the RF in Terminal, then try 
Automatic Channel Setting again.
Press to exit menu.
5
      NO CH FOUND
 PLEASE CHECK ANTENNA
 CABLE CONNECTION THEN
 PRESS OK KEY AGAIN
Tu n i n g  c h a n n e l s 
						

							28For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Use this setting when changing setting of receiving channels or changing the channel dis play.
3
Press to select 
MANUAL SET.
Press to display 
the MANUAL SET 
screen. Press the MENU button to display the MENU screen.
Press to select 
CHANNEL.
Press to display 
the CHANNEL 
screen.
Press to select 
TV or CABLE.Press to select 
ANTENNA.
1
2
Manual channel setting
Continued on the next page.
Tu n i n g  c h a n n e l s
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
OK
MUTEASPECTBBERECALL
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
$17(11$&$%/(
$8726(7
0$18$/6(7
&+$11(/&$37,21
:($.6,*1$/21*8,(
6(/(&7
6(7
0(18(1
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
$17(11$&$%/(
$8726(7
0$18$/6(7
&+$11(/&$37,21
:($.6,*1$/21*8,(
6(/(&7
6(7
0(18(;,7
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
$17(11$&$%/(
$8726(7
0$18$/6(7
&+$11(/&$37,21
:($.6,*1$/21*8,(
6(/(&7
6(7
0(18(;,7 
						

							29
Basic Operation
4
Press to select channel.
Repeat step 4 to continue adding or deleting channels.Press to add channels to memory.
Press to select channel.
Press to delete channels from memory.
Press to exit menu.
Note:
•   Some channels with very weak signals may be locked into memory. If desired, these channels can be deleted manually using 
the MANUAL SET feature.
5
6
To add channel
To delete channel
Tu n i n g  c h a n n e l s  
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
0$18$/6(7
(17(5&+$11(/
&+226($&+$11(/
86,1*&+$11(/832:1*8,(


$
0(18(;,7
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
0$18$/6(7
(17(5&+$11(/
&+226($&+$11(/
86,1*&+$11(/832:1*8,(
6(/(&7

(/(7(
0(18(;,7
123
456
78
09 
						

							30For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Operation can be done from the projection display.
Press to 
select the 
desired 
volume 
level. Press to select the desired 
channel. (Or use Number keys ) Press to turn the projection display on. Press to operate the projection 
display with the Remote Control.
1
2
3
4
Notes:
•   The channel number and volume level are stored even after the projection display is turned off.
•   Power consumption can be reduced if the volume level is lowered.
Or
 Remote  Control  Sensor POWER  button/
POWER indicator
 Volume up(+) / down(–) buttons
 Channel up / down buttons
&+

Note:
•   Refer to “Using the Number keys” on 
the next page.
Projection display operation
TV/VIDEO button
123
456
78
09
Press to select the desired 
channel. Remote Control
Unit
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
OK
MUTEASPECTBBERECALL