Panasonic Multimedia Projection Display Pt 43lc14 Operating Instructions

							31
Basic Operation
  Auto shut off
To extend lamp life, if there is no signal to the set’s tuner for 5 minutes, the lamp will shut off automatically.
Aspect types 
(P. 32)
Receivable 
broad cast  types 
(P. 37)Channel
Channel 
caption 
(P. 53)  TV status display
Using the  Number keys
Example 1: To select channel 125, fi 
rst press the 1 key, then 2, then 5. When selecting CABLE channels 100 to 125 with the Number keys, fi 
rst press the 1 key, 
and then enter the remaining two digits. Press the RECALL button, 
except when the MENU 
screen is dis played, to display 
current TV status information.
Example 2: To select channel 12, press the 1 key, then 2. Channel 12 appears momentarily.
Example 3: To select channel 8, press the 8 key. Channel 8 appears momentarily.
)5((=(Invalid operation notifi 
cation
If an invalid operation is attempted, the mark shown 
right is displayed.
Example: Invalid operation was tried 
during FREEZE mode.
Projection display operation
123
456
78
09 
						

							32For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
The color monitor will allow you to enjoy viewing the picture at its maximum size, including wide screen 
cinema format picture.
The aspect mode changes each time the  ASPECT 
button is pressed.
Notes:
•   When a 1080i or 720p signal is being received, the mode is set to FULL, and 
aspect switching is not possible.
)8//
Notes:
•   However, if the mode selected does not match the aspect ratio of the input signal, the original picture quality may be affected.
•   If using this projection display in places, such as cafes or hotels, with the aim of displaying programs for a commercial purpose 
or for public presentation, please note that by using the aspect ratio (16:9) selection function to change the aspect ratio, you 
may be infringing on the rights of the original copyright owner of that program under copyright protection laws.
•   If a normal (4:3) picture is projected in wide screen, distortion may occur around the edges so that part of the picture may no 
longer be visible. We recommend viewing in 4:3 mode so you can enjoy the picture as it was intended to be seen.
ASPECT Controls
•   During PC input, the mode switches between NORMAL and FULL only. •   When a 480p signal is being received, the mode switches between 
NORMAL, ZOOM, and FULL only.
NORMALZOOMFULL
NORMALFULL
NORMALFULL
JUSTZOOM
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
OK
MUTEASPECTBBERECALL 
						

							33
Basic Operation
Note:
•   The screen size changes if ID1 is detected. (P. 58)
ASPECT Controls
Mode Picture Ex pla na tion
NORMAL
1250$/
 
NORMAL will display a 4:3 picture at its 
stand ard 4:3 size.
JUST
-867
 
JUST mode will display a 4:3 picture at 
max i mum size but with aspect correction 
applied to the center of the screen so that 
elongation is only apparent at the left and 
right edges of the screen. The size of the 
picture will depend on the original signal.
ZOOM
=220


ZOOM mode magnifi 
es the central section of 
the picture.
FULL
)8//


FULL will display the picture at its maximum 
size but with sight elongation. 
						

							34For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
When the SEARCH/OPEN/CLOSE button is pressed 
during single screen.
When a channel button is pressed during channel 
search.
Sound from the left screen is 
output from the speakers on the 
projection display set. Channel search displays each channel, in order, as a paused image. Channels are dis played from the left top 
to the right bottom in order. When it reaches the right bottom, the next channel is displayed at the left top, 
overwriting the previously dis played channel.
Note:
•   To end channel search, press SEARCH/OPEN/CLOSE.
&+
Example: Select channel 6
&+
&+


Channel up and down buttons:
When ▲ or ▼ button is pressed, the next channel up or down is 
dis played in single screen. Number keys:
Example: When 6 is pressed, channel 6 is dis played in single screen. Example
Searching for the desired channel (Chan nel search)
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
OK
MUTEASPECTBBERECALL 
						

							35
Basic Operation
VC R
DV D pl aye r
This equipment can 
also be con nect ed to 
the rear terminals. See 
Connections for details.
Turning the power on and switching input modes
Turn the projection 
display on.
1
2
  The input mode changes 
each time this button is 
pressed.
*   If SKIP is set as the Input 
Label setting of SETUP, the 
mode will not be changed. 
(P. 52)
3Operate the connected equipment.
Confi 
rming connections
A video camera uses the Input 3 terminal on the front of the projection display.
Video camera To S-video output 
or video output
To  a u d i o  o u t p u t Example: Connect Input 3
VIDEO 1 Signal of source connected to INPUT 1 is displayed.
VIDEO 2 Signal of source connected to INPUT 2 is displayed.
VIDEO 3 Signal of source connected to INPUT 3 is displayed.
COMPONENT 1Signal of source connected to COMPONENT VIDEO INPUT 1 is displayed.
COMPONENT 2Signal of source connected to COMPONENT VIDEO INPUT 2 is displayed.
COMPONENT 3Signal of source connected to COMPONENT VIDEO INPUT 3 is displayed.
COMPONENT 4Signal of source connected to COMPONENT VIDEO INPUT 4 is displayed.
  RGB 1 (or RGB)Signal of source connected to RGB IN 1 (or RGB IN) is displayed.
RGB 2 Signal of source connected to RGB IN 2  is displayed.
HDMI Signal of source connected to HDMI IN is displayed.
CARD Signal of source connected to CARD SLOT is displayed.
TV
VIDEO 1 *
VIDEO 2 *
VIDEO 3 *
COMPONENT 1 *
COMPONENT 2 *
  HDMI*
COMPONENT 4 *COMPONENT 3 *
Card input mode is 
selected.
Playing peripheral equipment
RGB 2*(For PT-50LC14/ PT-60LC14)
RGB 1*(For PT-50LC14/PT-60LC14)
RGB*(For PT-43LC14)
Remote Control
Unit
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
OK
MUTEASPECTBBERECALL
•   Pressing SD again exits 
Card input mode. 
						

							36For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Press this button to mute the sound. Press again to 
reactivate sound. Sound is also reactivated when power 
is turned off or volume level is changed.
Projection can be switched between a frozen (still) 
picture and a moving picture each time the FREEZE 
button on the Remote Control unit is pressed. Press 
FREEZE button again to resume motion.
  Sound mute
Useful when answering the phone or receiving 
un ex pect ed visitors
 
Freezing pictures
)5((=(
087(
Note:
•   The audio output from AV OUT is not muted.
Note:
•   The video output from AV OUT is not frozen.
Mute / Freeze / SAP
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
OK
MUTEASPECTBBERECALL 
						

							37
Basic Operation
The following are possible broadcast types with their accompanying on-screen displays. The signal being 
received is indicated with a “ 
   ” mark while the se lect ed audio mode is indicated with an arrow. To change the 
audio mode for these broadcasts, fol low the “Select Audio Mode for TV Viewing” sec tion (be low.)
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main lan guage) and Secondary 
Au dio Program (sub lan guage) broad casts are both be ing received 
si mul ta ne ous ly. Select the STEREO or SAP audio mode.
MTS Stereo broadcast
Multi-channel Television Sound Stereo broadcast. Se lect STEREO 
audio mode.
•   If stereo broadcast is weak and the display fl 
ickers, select MONO audio 
mode for pos si bly better results.
SAP broadcast
Secondary Audio Program (sub language.)
Select SAP audio mode for the sub language.
MONO broadcast
Normal monaural sound broadcast.
  Receivable Broadcast Types
67(5(2
6$3
0212
67(5(2
6$3
0212
67(5(2
6$3
0212
67(5(2
6$3
0212
Press SAP button to select the desired audio mode as described below.
(Arrow shows selection.)
•   Each press of SAP button will change the audio mode as shown below.
•   “SAP” is selected with fi 
rst press of SAP button.
Select Audio Mode for TV Viewing
Example:
Press 
SAP
Mute / Freeze / SAP 
Press 
SAP
67(5(2
6$3
021267(5(2
6$3
021267(5(2
6$3
0212
Press 
SAP 
						

							38For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Notes:
•   Sound from the Left screen is output from the speakers on the projection 
display set.
•   When the screen is split, signals of the Left screen are output from the rear 
monitor output terminal.
•   The left and right screens are processed by individual circuits and, 
therefore, may vary in image quality.
•   Split screen returns to single screen when the projection display is turned 
off.
•   With the Left screen, as with a single screen, you can change the input, 
change channels, and adjust the volume.
•   The right and left screens cannot display the same picture at the same time.
•   CARD input screen cannot be displayed using the Split Screen function.
•   When viewing a split screen with HDMI as the input signal of the Left 
screen, if the HDMI signal is incompatible (see P. 21) or is nonexistent, the 
entire screen will go black and “SIGNAL” will be displayed.
Splitting the screen
Press to split.
(The previously selected screen appears on the left.)
Returning to one screen
Press to return.
&+&+
 Left  screen
( Main  pic ture) Right  screen
(Sub pic ture)
Split screen
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
OK
MUTEASPECTBBERECALL 
						

							39
Basic Operation
Swapping left and right screens
Example:
During SPLIT SCREEN NORMAL
&+&+
Changing the channel of the right screen
&+
Press to swap.
Example:
During SPLIT SCREEN NORMAL
Note:
•   When outside input is fi 
nished, the low est reg is tered 
chan nel number is displayed. For fast er selection, 
press the SWAP but ton to change the screen to the left. 
Then, press the TV/VIDEO but ton to directly change 
the input. Finally, press SWAP button again to change 
the screen back to the right.
Press to select the desired 
channel.
SPLIT CH ▲, ▼ buttons can also be used to select 
an outside input for the right side of the screen.
*   If SKIP is set as 
the Input Label 
setting of SETUP, 
the mode will 
not be changed. 
(P. 52)
Note:
•   Picture quality may change according to the 
combination of signals input to the left and right 
screens.
Split screen
CH 125
VIDEO 1 *
VIDEO 2 *
VIDEO 3 *
COMPONENT 1 *COMPONENT 2 *
HDMI*
COMPONENT 4 *
COMPONENT 3 *
CH 01
or CA BLE 
125TV 
69 
						

							40For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
5
Press the MENU button to display the MENU screen.
Press to select 
OTHER.
Press to display 
OTHER screen.
Press to set or adjust 
to desired level.
(See next page.)2
4
Press to select the screen mode.1
RGB input
ZOOM modeNOR MAL mode JUST mode
Press to exit menu.Press to select 
each item.
Note:
•   NORMAL is displayed at default.
Adjusting screen position and size
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
6/((37,0(52))
326,7,216,=(*8,(
6(/(&7
6(7
0(18(1
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
6/((37,0(52))
326,7,216,=(*8,(
6(/(&7
6(7
0(18(;,7
Press to select 
POSITION/SIZE.
Press to display 
POSITION/SIZE 
sub-menu.
3
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
326,7,216,=(
+:,7+(1/$5*(
1250$/*8,(
6(/(&7
6(7
0(18(;,7
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
326,7,216,=(
+:,7+1$552:
1250$/*8,(
6(/(&7
6(7
0(18(;,7
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
326,7,216,=(
96,=(
1250$/*8,(
6(/(&7
6(7
$-867
0(18(;,7
3,&785(
$8,2
&+$11(/
6(783
/2&.
27+(5
/$1*8$*(
326,7,216,=(
+326
9326
+6,=(
3+$6(
1250$/*8,(
6(/(&7
6(7
$-867
0(18(;,7
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
SWAP
REW
FREEZE
TV/VCRSPLIT CH
DVD/VCR CHSEARCH
OPEN/CLOSE
SPLIT
PLAY
PA U S E S T O P R E CSPLIT CTRLFF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DTV RCVR
DBS/CBLAUX
OK
MUTEASPECTBBERECALL