Panasonic Multi Format Live Switcher Av Hs400an Operating Instructions

61
4. Input/output signal settings
4-1. Setting the SDI input signals and analog input signals
The user can set the SDI input signals and analog input signals. 
IN5 to IN8 can be set only when one of the following optional boards has been connected:SDI input board
Analog input board
Analog composite input board
4-1-1. Setting the frame synchronizer
The frame synchronizer can be set to On or Off for each input.
The DVI input (option) frame synchronizer is permanently On. It cannot be set from On to Off or...

62
4. Input/output signal settings
4-1-2. Setting the input mode
The mode can be set for each input only when HD has been selected as the system format. 
When SD is selected as the system format, the input mode is always the same as Normal.Normal: 
  Input signals in conformity with the system format take effect.
D by D: 
  When SD signals with the same frame rate as the system format have been input, they are input on a 
dot by dot (1 magnification) basis with no up-conversion.
 

  (This setting is...

63
4. Input/output signal settings
4-1-3. Setting the analog input gain
When the analog input board (option) has been connected, the gain of t\
he input signals can be set. 
Alternatively, when the analog composite input board (option) has been connected, t\
he gain of the Y signals can 
be set.
The setting range is ±30 steps, and the gain changes by approximately ±2 dB. The amount of change in the gain 
when it is changed by one step is not fixed.1 
 On the Input sub menu, turn [F2] to select the input...

64
4. Input/output signal settings
4-2. Setting the up-converter (option)
Select the settings for the up-converter that is built into the optional boards listed below.SDI input board
Analog input board
Analog composite input board
1 
 Press the [FUNC] button to light its indicator, and press the [IN/OUT] button to display the IN/OUT menu.
2 
  Turn [F1] to display the UpConvt sub menu.
  An asterisk (
) appears at the left of the parameter currently selected.
  
 
UpConvt Signal Scale↓ MovDet↓ Sharp↓...

65
4. Input/output signal settings
4-3. Setting the DVI input signals (option)
4-3-1. Setting the DVI input signals
The user can set the DVI input signals when the DVI input board (option) has been connected. Signals with the 
following resolutions can be input. If signals with any other resolution or frequency are input, the picture will turn 
black.  
 XGA (1024768), 60 Hz
  
  WXGA (1280768), 60 Hz
  
  SXGA (12841024), 60 Hz
1 
  Press the [FUNC] button to light its indicator, and press the...

66
4. Input/output signal settings

DVI format ModeHD/1080i HD/720P SD/NTSC SD/PAL
1920  1080 1280  720 720  480 720  576
XGA
1024768
Fit-V


480 720576720
Fit-H
Full


480 720576720
SXGA
12801024Fit-V


480 675576675
Fit-H
Full


480 720576720
WXGA
1280768Fit-V
Fit-H
Full
: Black images are inserted here.: The parts of the images protruding in these areas are cropped. 

67
4. Input/output signal settings
4-3-2. Adjusting the DVI input signals
Adjust the clock/phase and position of the DVI input signals.1 
 Press the [FUNC] button to light its indicator, and press the [IN/OUT] button to display the IN/OUT menu.
2  T
urn [F1] to display the DVIPhs sub menu.
 
 
DVIPhs Signal ClkPhs H-Pos V-Pos
  11/15     IN5       0       0       0   IN5-8
    −16
     |
    +15   −100
     |
   +100   −100
     |
   +100
3  Turn [F2] to select the input signal using the Signal item.
4...

68
4. Input/output signal settings
4-4. Setting the output signals
4-4-1. Types of output signals
There are five output signal types: PGM, PVW, AUX, MULTI and KEYOUT.
Five lines of output signals can be assigned to OUTPUT1 to 6.PGM: 
  This is the main-line output of the switcher; images with wipe, mix, key and other effects added to 
them are output.
PVW:  This is the pre
 view output which enables the next operation to be checked in advance.
AUX:  Signals selected b
 y the AUX bus are output.
MULTI:...

69
4. Input/output signal settings
4-4-2. Assigning the output signals
Assign the output signals to OUTPUT1 to 6.1 
 Press the [FUNC] button to light its indicator, and press the [IN/OUT] button to display the IN/OUT menu.
2 
  Turn [F1] to display the Output sub menu.
3 
  Turn [F2] to select the signal name using the Signal item, and turn [F3] to set the type of output signal using 
the Output item.  
  
 
Output Signal Output Mode↓
  2/15    OUT1     PGM Normal
OUT1-6
    PVW
    AUX
  Multi
 KEYOut...

70
4. Input/output signal settings
4-5. Setting the sync signals
The sync signals to be used by the system can be selected.External sync: 
  
For synchronization with an external sync signal (gen-lock).  
The reference input signal is looped through and output.
BBST:  Blac
 k burst signal (vertical phase of 0H)
BBAD: 
  Black burst signal 
(
  Vertical phase of 90H when the 59.94i or 59.94p format is selected;   
vertical phase of 75H when the 50i or 50p format is selected)
TRI: 
  Tri-level sync signal...