Panasonic Multi Format Live Switcher Av Hs300g Operating Instructions

1

2. Basic operations
Adjusting the fill color
The fill color can be adjusted when USR1 to 4 have been selected. Use of USR1 to 4 is shared by the border 
color, color background and edge color.
1 Press the [FUNC] switch to light its indicator, and then press the [KEY] switch to display the KEY menu.
2  Turn [F1] to display the USR1 to 4 (user color) menu.
3  Turn [F], [F3] and [F4] to adjust the color (HUE, SAT and LUM).
‰‰‰
643


)6&




45




-6.


2-3-5. Key...



2. Basic operations
Adjusting the edge color
The edge color can be adjusted when USR1, , 3 or 4 has been selected. Use of USR1 to 4 is shared by the 
border color, color background and fill color.
1  Press the [FUNC] switch to light its indicator, and then press the [EDGE] switch to display the EDGE menu.
2  Turn [F1] to display the USR1 to 4 (user color) menu.
3  Turn [F], [F3] and [F4] to adjust the color (HUE, SAT and LUM).
‰‰‰
643


)6&




45




-6.

 

3

2. Basic operations
2-4. Color background
The color background to be used by the bus can be set.
One color among the eight preset colors (WHITE, YELLOW, CYAN, GREEN, MAGENTA, RED, BLUE and BLACK) 
and four user colors can be selected. HUE, SAT and LUM adjustments can be performed for the user colors.
1 Press the [FUNC] switch to light its indicator, and then press the [CBGD] switch to display the CBGD menu.
2  Turn [F], and select the color using the COLR item.

:-8

$:/

(3/

.(5

3&%...

4

2. Basic operations
2-5. Freezing the input signals
The input signals can be frozen and used. If any of the input signals has been frozen, the freeze status display 
LED lights. While signals are frozen, the tally signals of the corresponding input will not be output.
1 Press the [FUNC] switch to light its indicator, and then press the [FRZ] switch to display the FRZ menu.
2  Turn [F1] to display the FRZ (/) menu.
3  Turn [F], and select the input video signals using the SIG...

5

2. Basic operations
2-6. Frame memory
AUX output signals can be stored in the frame memory for use. Stored images can be used as the bus images by 
assigning the FMEM signals using the crosspoint assignment process.
Images stored in the frame memory are also saved in the unit’s flash memory so they can be used even after the 
power is turned off. Stored images have an 8-bit format so the image quality may appear rough at times.
1 Press the [FUNC] switch to light its indicator, and then press the...

6

2. Basic operations
2-7. Preset memory
Up to 10 panel settings can be stored in this memory.
The table below lists the settings which are stored.

ItemDescription of settingInitial value (factory default)
CrosspointA bus1
B bus1
KEY-S1
KEY-F1
AUX bus1
Color backgroundWHITE
WipeWipe pattern4 (center) 
Border width0
Soft effect width0
Border colorWHT
Transition areaBKGD/KEY selectionBKGD
MIX/WIPE selectionMIX
Auto transition time (BKGD)30F
Auto transition time (KEY)30F
KeyKey type (TYPE)LIN
Key...

7

2. Basic operations
RECALL: This is used to recall the preset memory data and change the panel settings.
1  Press the [FUNC] switch to light its indicator, and then press the [MEM] switch to display the PSMEM (1/3) 
menu.
2   Turn [F], select “RECL” using the MODE item, turn [F3], and set the preset memory number using the NO. 
item.
3   Press the [F4] switch (EXEC) to recall the settings. 
If the asterisk () is not displayed at the left of the preset memory number, the panel status will...

8

3. Setup
3-1. Setting the input signals
3-1-1. Setting the input signals (IN 1 to 5)
If HD has been selected as the system format, SDI or analog HD component can be selected for each input. 
This selection is possible only when the HD analog board has been connected.
1  Press the [FUNC] switch to light its indicator, and then press the [SETUP] switch to display the SETUP 
menu.
2  Turn [F1] to display the IN1 to 5 menu.
3   Turn [F], select the input signals using the SIG item, turn [F3],...

9

3. Setup
3-1-3. Setting the DVI input signals (IN6)
Selecting the signal system
Select the digital or analog system for the DVI input video signals.
DIG (digital):  Digital input signals of the DVI connector are effective.
ANLG (analog) :  Analog input signals of the DVI connector are effective.
1   Press the [FUNC] switch to light its indicator, and then press the [SETUP] switch to display the SETUP 
menu.
2  Turn [F1] to display the DVIIN menu.
3  Turn [F], and select the signal system...

30

3. Setup
Adjustment
Adjust the clock/phase and position of the DVI input signals.
1  Press the [FUNC] switch to light its indicator, and then press the [SETUP] switch to display the SETUP 
menu.
2  Turn [F1] to display the DVIPH menu.
3   Turn [F] to adjust the clock/phase of the analog input signal using the CKPH item. 
Adjust this setting so that the noise will be minimum level.
4  Turn [F3] to adjust the horizontal position using the HPOS item.
5  Turn [F4] to adjust the vertical position...