Panasonic Mp3 Cd Player Sirius XM-Ready Cq 5109u Operating Instructions

							31
Installation Guide (continued)
Securing of the main unit
 Caution
¡ We strongly recommend that you wear gloves for installation work to prote\
ct yourself from injuries.
¡ When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure 
your hands and fingers.
First complete the electrical connections, and then check them for corre\
ctness. (a  page 33)
The included Mounting Collar q is designed specially for this unit. Do not use it to attach any other \
model.
    
1
2
3
Insert Mounting Collar q into the dash-
board, and bend the mounting tabs out with 
a screwdriver.
Establish the rear connection of the unit.
After fixing Power Connector, fix the rear of the 
unit to the vehicle body by either method (a) or 
(b) shown in the previous page.
After installation reconnect the negative (–) 
battery terminal.
The tabs to be bent vary depending 
on the vehicle.  To securely install the 
unit, fully bend a number of the tabs 
so that there is no rattling.
Example: Ta b
q 
 Mounting 
Collar
Power Connector
Mounting Holes
Mounting Bolt
Mounting springs
Engage the Mount

-
ing Springs in the 
mounting holes of 
the Mounting Collar 
q firmly. Mounting
Hole
Mounting Spring 
						

							32
Removing the unit from the vehicle’s dashboard
Insert each Removal Tool i and pull.
i  Removal Tool 
(U-shaped)
Note: Do not lose Removal Tools. They will be needed to remove the unit from the vehicle’s dashboard.
Installation Guide (continued) 
						

							33
Electrical Connections
 Caution
¡ This wiring information is for experienced technical individual, for saf\
ety reason, please your dealer wire 
this connection.
¡
 This product is designed to operate with a 12 V DC, negative 

@ ground battery system.
¡
 T

o prevent damage to the unit, be sure to follow the connection diagram b\
elow.
¡
 Do not insert the power connector into the unit until the wiring is comp\
leted.
¡ Be sure to insulate any exposed wires from a possible short-cir

cuit from the vehicle chassis. Bundle all 
cables and keep cable terminals free from touching any metal parts.
¡
 Remember

, if your vehicle has a drive computer or a navigation computer, the data of its memory 
maybe erased when the battery terminals are disconnected.
Wiring diagram
(Rear Side)
Main Unit
Antenna
Accessory Power(ACC)
(+12 V DC, negative ground
 only)
Ground Lead
(Connect to a clean, bare
 metallic part of your vehicle)
Battery Lead
(Connect to vehicle battery)
(Red)
ACC
Ground (Black)
(Yellow)
Battery
(Violet)
(Violet/Black)
(Gray/Black) (Green)
(Green/Black)
(White/Black)
(Gray)
(White)
Left Speaker (Front) Right Speaker
(Front) Left Speaker
(Rear) Right Speaker
(Rear)
Power Connector
SiriusXM Tuner Connector
(Connect to the optional SiriusXM Connect Vehicle Tuner.)
(Refer to next page)
*Fuse (15 A)Refer fuse replacement 
to your dealership. 
Do not try fuse 
replacement by yourself.
The power connector does not come
along with the unit. If need, please
consult your dealership.
Detail of power connectorCavity FUNCTION
PIN FUNCTIONA REAR SP R (+)AREAR SP R (–)AFRONT SP R (+)AFRONT SP R (–)AFRONT SP L (+)A
Battery
Ground FRONT SP L (–)A
REAR SP L(+)
A REAR SP L(–)
ACC
Cavity
B
B
B
B
B
B
B
B
PIN
12
3
4
5
6
7
8 1
2
3
4
5
6
7
8
  1  3  5  7
1
2 4 6 8 3 5 7
 2
 4  6  8Cavity B
Cavity A 
						

							34
 Caution
Please follow the instructions given below. Failure to do so will cause damage to the unit and speakers.
Speaker Connections
Connection with optional SiriusXM Connect Vehicle Tuner
L
R
- 
- 
-  - 
- - 
-  - 
- 
- +
+
+ +
++
+
+ +
+- +
- +
- +- +- +
- +- +- +
L
R
L
R
L
R


(White)
(White/Black)
Chassis
(Gray/Black) (Gray)
Chassis
¡ Use ungrounded speaker only
.
¡ The maximum speaker input should be 45 W or more.  (If used with the 
optional power amplifier
, the speaker input should be higher than the maxi-
mum amplifier output.)
¡
 The speaker impedance should be 4 – 8 

Ω.
¡
 This unit uses the BTCL cir

cuit, so each speaker should be connected sepa-
rately using parallel vinyl insulated cords.
¡
 The speaker cords and the power amplifier unit should be kept away (a\
bout 
30 cm apart) from the antenna and antenna extension cord.
¡
 Never connect the speaker 
cord to the body of the car

. ¡
 Do not use a 3-wire type 
speaker system having a com

-
mon earth lead. ¡
 Do not connect more than one 
speaker to one set of speaker 
leads.
Electrical Connections (continued)
CONNECT
SiriusXM Connect Vehicle Tuner (Optional)
Satellite Radio Antenna
Main unit
Direction when connection Note:
 Please notice the cable direction for 
correct connection. Note: Refer to installation guide included with the 
SiriusXM Connect Vehicle Tuner for more information. 
						

							35
Specifications
General
Power Supply: 12 V DC (11 V – 16 V), test 
Voltage 14.4 V, Negative @ 
ground
Current consumption:
 
Less than 2.5 A (CD mode, 
0.5 W 4-speaker)
Maximum Power Output:

 
45 W × 4 channels at 400 Hz, 
V

olume Control maximum
Tone adjustment range:
 
 
Bass:

 
± 12 dB at 100 Hz T

reble:  
± 12 dB at 10 kHz
Power Output:

 
18 W per channel into 4 
 Ω, 
40 to 30 000 Hz at 3 % THD
Suitable Speaker 
Impedance:
 
4 – 8 
 Ω
Dimensions (W x H x D):
 
178(W) x 50(H) x 160(D) mm 
{7” x 1-15/16” x 6-5/16”}
W

eight:  
1.4 k
 g {3 lbs. 1 oz.}
Front AUX Input
Input impedance: 10 kΩ
Maximum input level:  2.0 V
Connector:
 
3.5 mm ø stereo mini pin
Input sensitivity:

 
200 mV
 rms
FM Stereo Radio
Frequency Range: 87.9 – 107.9 MHz
Usable Sensitivity:  12 dBf (1.1 μV/ 75  Ω,  
S/N 30 dB)
50 dB Quieting Sensitivity: 17 dBf (1.8 μV/ 75  Ω)
Frequency Response:
 30 – 15 000 Hz ± 3 dB
Alternate Channel
Selectivity:
 
75 dB
Stereo Separation:

 
35 dB at 1 kHz
Signal/Noise Ratio:

 
70 dB (Mono)
AM Radio
Frequency range: 530 kHz – 1 710 kHz
Usable sensitivity:  28 dB/ μ V (25  μ V, S/N 20 dB)
Weather Band Radio
Frequency range: 162.400 – 162.550 MHz
Usable sensitivity:  3 dB/μV (S/N 20 dB)
Signal/Noise Ratio
(40 dB/μV):
 
50 dB
CD Player
Sampling Frequency: 8 times oversampling
DA Converter:  1 bit DAC System
Pick-Up T
ype:  
Astigma 3-beam
Light Sour

ce:  
Semiconductor laser
W

avelength:  
790 nm
Frequency Response:

 
20 – 20 000 Hz (±1 dB)
Signal to Noise Ratio:

 
96 dB
W

ow and Flutter:  
Below measurable limits
Channel Separation:

 
75 dB
Above specifications comply with EIA standards.
Note: Specifications and the design are subject to 
modification without notice due to improvements in 
technology.
Power Output: 
16 W RMS x 4 Channels at 4  Ω and ≤ 1% THD+N
Signal to Noise Ratio: 
85 dBA (reference: 1 W into 4 Ω)  
						

							YFM264C241ZB     PTW0411-2061     Printed in Taiwan