Panasonic Mp3 Cd Player Sirius XM-Ready Cq 5109u Operating Instructions

							11
 Sound  Controls
DISPDISP
 Audio modes (Bass/ Treble/Balance/Fader)
 1 Push [SEL] (Select) to select the audio mode in sequence.2   Turn  [VOL] (Volume) clockwise or counter-
clockwise to change each level or select a 
setting.
 (Volume)
 (Bass)
 (Treble)
 (Balance)
 (Fader)  q
: Up
w: Down
 q : Increased
w: Decreased
 q : Increased
w: Decreased
 q : Right enhanced
w: Left enhanced
 q : Front enhanced
w: Rear enhanced
 (Setting Range: 0 to 40, default: 18)
 (Setting Range: –12 dB to +12 dB by 2 dB, 
default: 0 dB)
 (Setting Range: –12 dB to +12 dB by 2 dB, 
default: 0 dB)
 (Setting Range: 15 levels each and 0 (center), 
default: CNT)
 (Setting Range: 15 levels each and 0 (center), 
default: CNT)
 Note: If no operation takes place for more than 5 
seconds in audio mode (2 seconds in volume mode), 
the display returns to the regular mode.
 SQ (Sound Quality) 
 (FLAT) fl at frequency response:
does not emphasize any part. (default)
 (ROCK) speedy and heavy sound:
exaggerates bass and treble.
 (POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
 (VOCAL) clear sound:
emphasizes middle tone and slightly 
emphasizes treble. SQ is a function that can call up various sound 
types at the touch of button in accordance with your 
listening music type.
Hold down [SQ] for more than 2 seconds to 
select the sound type as follows:
 Note: Settings of SQ, bass and treble are infl uenced 
one another. If such an infl uence causes distortion 
to the audio signal, readjust bass/treble or volume. 
						

							12
 Radio
 Band
Press [BAND] to change the band.
 Weather  Band
(a page 13)
  Caution
 To ensure safety, never attempt to preset stations while you are driving.
 
 (FM stereo) indicator
lights while receiving an FM stereo 
signal.
DISPDISPDISPDISP
 Frequency  adjustment
[TUNE/SEEK }]: Higher
[TUNE/SEEK {]: Lower
Note: Hold down for more than 0.5 seconds and 
release for station search.
 Preset station selection
Press the corresponding preset button [1] 
through [6] to tune in a preset station.
 Auto preset memory (APM)
Press and hold [APM] (Auto Preset Memory) 
for more than 2 seconds.
¡  The 6 stations with good reception will be au-
tomatically saved in the memory under preset 
buttons [1] through [6].
¡  Once set, the preset stations are sequentially 
scanned for 5 seconds each.
¡  Press one of the buttons [1] through [6] to stop 
sequentially scan.
Note: New stations overwrite existing saved sta-
tions.
 Manual preset memory
1 Use manual or seek tuning to fi nd a sta-
tion.
2 Press and hold one of the preset buttons [1] through [6] until the display blinks 
once.
 
 Preset  Number
 blinks  once
Note: New stations overwrite existing saved sta-
tions.
 Display  Change
Press [DISP] (display) to switch to the clock 
display.
   
 Radio  mode 
display
	
    Clock  display 
						

							13
Radio
Tuning in a weather band station
1 Press [BAND] to select WB (Weather Band). (a  page 12)
2 Press any of the buttons [1] through [6] to 
monitor the preset station.
Note: The weather band (CH1-6) has been pre-
set. CH7 is selected by pressing [TUNE}] or 
[TUNE{].
Weather Band Stations
National Weather Radio Broadcasts from over 380 
Iocations throughout the U.S. on seven VHF/FM 
frequencies.
Tune to weather band to receive continuous weather 
information 24 hours a day on one of the following 
frequencies.
1. 162.550 MHz
2. 162.400 MHz
3. 162.475 MHz
4. 162.425 MHz
5. 162.450 MHz
6. 162.500 MHz
7. 162.525 MHz
Note: Further and updated information about the 
National Weather Radio station listing, please visit 
the web site: 
http://www.nws.noaa.gov/nwr/nwrbro.htm
Occasionally the frequency of an existing or planned 
station must be changed because of unexpected 
radio frequency interfere with adjacent NOAA 
weather Radio Stations and/or with other Govern-
ment or commercial Operations within the area. 
If you have a question concerning NOAA Weather 
Radio, please contact your nearest National Weather 
Service Office.
 Warning
Any NOAA broadcast weather report, including 
current and forecasts, may not reflect your actual 
weather conditions at your exact time and loca-
tion. You should always pay attention to your 
actual weather conditions to make safe decisions 
accordingly.
Weather Band Frequency 
(channel) Number
Weather Band Indicator
Weather Band Frequency  
						

							14
 CD/MP3  Player
  Caution
	¡ Do not insert a disc when the  indicator 
lights.
	¡  This unit does not support 8 cm {3”} discs.
	¡  Do not use irregularly shaped discs. (a  page 28)
	¡  Do not use discs that have a seal or label at-
tached.
	¡  Do not insert foreign matter into the disc slots.
	¡  This unit does not support WMA disc playback. 	¡
 Refer to the section on “Notes on CD-Rs/RWs” 
(a  page 28).
	¡  Refer to the section on “Notes on MP3”. 
(a  page 26)
	¡  This unit does not support a MIX mode CD 
(a  CD containing both CD-DA and compressed 
audio data). In case of using such a CD, prob-
lems may occur such as anacoustic playback.
 Pause
Press [h / 5] (Pause/Play)
Press again to cancel.
 Disc  loading/ejection
Loading
Load a disc in with the printed side facing up.
Notes:
¡  The power will be turned on automatically when a disc is 
loaded.
¡  Playback will start automatically after the player recog-
nized the loaded disc as an ordinary music CD or MP3 
disc.
Ejection
Press [u] (Eject) to eject the disc.
DISPDISPDISPDISP
  (DISC) 
indicator
   (Repeat)/ (Random)/ indicator
 Text  Scroll
 Scan, Repeat, Random (a  page 15)
Track /File selection
[FILE d]: Next track/fi le
[FILE s]:  Back to the beginning of the cur-
rent track/fi le. 
Back to the previous track/fi le. 
(press twice)
Note : Hold down for fast forward/reverse. Release 
to resume the regular play.
 Folder selection (MP3)
[FOLDER }]: Next folder
[FOLDER {]: Preceding folder
 
 Display  Change
(a page 15) 
						

							15
CD/MP3 Player
Display change
Press [DISP] (Display) to change the display.
Notes:
¡ For scrolling text, press [SCROLL].
¡
 “NO TEXT” is displayed when there is no information on the disc.
Track number/
Play time Folder number/
File number
Play time
Folder name/ 
Album*
File name/
Title, artist*
Clock
Disc title*
Track title*
Clock
CD-DA
MP3
* CD TEXT Display
 Disc title and Track title name are displayed.
* ID3 Tag ON/OFF
Hold down [SCROLL] for more than 2 seconds.
TAG ON: album title and song title/artist name 
are displayed.
TAG OFF: folder name/file name are displayed. 
(Default)
Scan, repeat, random
Scan play
The first 10 seconds of each track/file is played in 
sequence.
Press [SCAN]. Track/file number blinks.
Press again to cancel.
Folder scan play (MP3)
From the next folder, the first 10 seconds of the first 
file in each folder is played in sequence.
Hold down [SCAN] for more than 2 seconds.  lights and folder number blinks.
Hold down again to cancel.
Repeat play
The current track/file is repeated.
Press [REPEAT].  lights.
Press again to cancel.
Folder repeat play (MP3)
The current folder is repeated. 
Hold down [REPEAT] for more than 2 sec-
onds. ,  lights.
Hold down again to cancel.
Random play
All the available tracks/files are played in a random 
sequence.
Press [RANDOM].  lights.
Press again to cancel.
Folder random play (MP3)
All the available files in current folder are played in a 
random sequence.
Hold down [RANDOM] for more than 2 sec-
onds. ,  lights.
Hold down again to cancel. 
						

							16
DISPDISPDISPDISP
 SiriusXM Satellite Radio Control
Connecting SiriusXM Tuner
Connect the optional SiriusXM Connect Vehicle 
Tuner.
Refer to the installation instructions included with 
the SiriusXM receiver and the fi gure on page 34 of 
this manual.
Getting started
A SiriusXM subscription (sold separately) is re-
quired to receive programming. You can subscribe 
by calling SiriusXM listener care or by going on line 
- see below for details.
1 Check the Radio ID.
¡	Write down the Radio ID from your SiriusXM 
Connect Vehicle Tuner.
¡  To show the Radio ID on the display, tune to 
channel 0. (Refer to “Channel Selection”.)
   
Radio ID display 
(example)
2 Activate the SiriusXM Satellite Radio by 
calling or going on-line:
¡  Web site: 
http://www.siriusxm.com/subscriptions
¡  Phone number: 1-800-967-2346
Note: 
The Radio ID does not use the letter I, O, S, or F.
Band selection
Press [BAND] to change the band.
 
Channel selection
[TUNE/SEEK }]:   Next available/subscribed 
channel
[TUNE/SEEK {]:  Preceding available/sub- scribed channel
Hold down for seek forward/reverse.
Note: “CH LOCKD” is displayed if a channel is 
selected that has been locked by the parental lock 
setting, follow the procedure next on “Channel 
unlocking” to unlock the channel.
Channel unlocking (passcode entry)
To receive a channel locked by a parental lock, a 
passcode needs to be entered after tuning to the 
channel. (Refer to page 19 for parental lock setting.)
1 Tune to a channel locked by a parental lock. 
  
	
  
	
 
2 Press  [d] or [s] to select a number. 
 
3 Press [BAND] to shift to the right adjacent 
digit. 
 
A digit where entry is determined is indicated as 
“ * ”. 
 [BAND]
 [SEL]
 [DISP]
 [TUNE/SEEK }] 
(d) [TUNE/SEEK {] (s)
Signal strength indicator Satellite Radio indicator (lights when connected 
with optional SiriusXM Connect Vehicle Tuner)
 [1] through [6] (Preset Buttons) 
(FOLDER }/FOLDER {) 
						

							17
SiriusXM Satellite Radio Control
4 Repeat the steps 2 and 3 to enter a 4-digit 
number code. 
When a 4-digit number code is correctly entered 
and [BAND] is finally pressed, the all locked 
channels are unlocked and start to be received. 
(Once turns ACC ON/OFF, the channels return to 
previous locked status) 
Notes:
¡
 If a wrong number code is entered when selects a 
locked channel, “WRONG CODE” is displayed and 
returns to Channel 1.
¡
 If 10 seconds elapse before determining the entr

y 
of the number code, “TIME OUT” is displayed and 
returns to previous channel.
¡
 T

o exit the passcode entry, press [DISP] and 
returns to previous channel.
¡
 T

o change the parental lock passcode, refer to 
page 19 for setting.
Channel preset
Up to 6 channels can be preset in SXM1 to SXM3 
respectively.
1 Use manual or seek tuning to tune into a 
channel.
2 Press and hold one of the preset b uttons 
[1] through [6] until the display blinks 
once.
 
Preset Number
blinks once
Note: New channels overwrite existing saved chan-
nel after this procedure.
Preset channel selection
Press the corresponding preset button [1] 
through [6] to tune in a preset channel.
Selection by category
Category setting
You can toggle the category selection mode ON and 
OFF every time you press and hold [BAND] for 
more than 2 seconds. If the category is set to ON, 
the unit operates as follows for each button:
Notes: 
¡
 When categor

y is set to ON, the letter “c” is 
displayed followed by channel number.
¡
 When categor

y selection mode is active, as 
indicated by “c”, the preset buttons are disabled. 
Turn off category selection mode to re-enable the 
preset buttons.
Category selection
[FOLDER }]:  Ne xt category
[FOLDER {]:   
Preceding categor
 y
Channel selection
[TUNE/SEEK }]:  Next available/subscribed 
channel in current cat-
egory
[TUNE/SEEK {]: 
 
Preceding a
 vailable/sub-
scribed channel in current 
category
Note: The simulate category of “All Channel” is 
selectable in category selection.
Display change
Press [DISP] (Display) to change the display 
of different metadata information.
Band/
channel number
(Data reading)
(Data reading)
(Data reading)
(Data reading)
(Data reading)
Channel name 
(Default)
Artist name
Song title
Information of 
contents
Category name
Clock
Note: “– – – –” is displayed when there is no infor-
mation on the selected channel. 
						

							18
DISPDISPDISPDISP
 SiriusXM Satellite Radio Control (continued)
System control mode selection  
Function settings
 [BAND] [DISP]
[SEL]
 [TUNE/SEEK }] (d) [TUNE/SEEK {] (s) Satellite Radio indicator
Signal strength indicator
SiriusXM radio display
Press and hold [SEL] for more than 2 seconds to open SXM function setting screen.
Turn [SEL] to open alarm time setting screen.
Turn [SEL] back to SXM function setting screen.
SiriusXM function setting mode 
Note: See below “Function settings” for its inside setting.
Alarm time setting mode
Note: 
Refer page 20 and follow its steps from 2 to 6 to set alarm time if needed.
Channel direct selection mode
A channel is directly selected with the channel 
number entry.
1 Press and hold [SEL] for more than 2 sec-
onds to open SXM function setting screen.
 
2 The radio automatically enters the SXM direct channel selection mode after 2 
seconds when entering the SXM function 
setting screen.
   
Channel direct 
selection mode
3  Press  [d] or [s] to select a number. 
 
4 Press [BAND] to enter the next digit. 
 
5 If necessary, repeat steps 3 and 4 to enter 
more digits of the channel number.
6 Press  [SEL] when done entering the chan-
nel number digits and the radio tunes to 
the desired channel.
Notes:
¡  ”CH UNAVL” is displayed when the requested 
channel is not valid. Visit www.siriusxm.com to 
see the list of channels available. 
¡  ”CH UNSUB” is displayed when the requested 
channel is not part of the current subscription 
package. Visit www.siriusxm.com for information 
on subscription packages. 
						

							19
SiriusXM Satellite Radio Control (continued)
Parental lock setting mode
This function disables the audience from selecting 
the locked channel. 
1 Press and hold [SEL] for more than 2 
seconds to open SXM function setting 
screen.
 
2 When “D. TUNING” is displayed, press  [SEL] to select parental lock setting 
mode.
   
(Parental lock 
setting mode)
3 Enter a 4-digit passcode , then press 
[BAND] when finished.
 q Press  [d] or [s] to select a number. 
w
 
Press  [BAND] to shift to the right adjacent 
digit. 
 A digit where entr

y is determined is indicated 
as “ *”. 
e
 
Repeat the steps 

q and w to enter a 4-digit 
number. 
Note:  (Default: 1111). If you want to initialize the 
passcode, press and hold [DISP] for more than 10 
seconds while passcode entry, the 4-digit passcode 
will return to the default.
4 Press  [TUNE /SEEK }] or [TUNE/SEEK 
{] to select a channel. 
5 Press  [BAND] to switch a select channel 
to be locked or unlocked.
   unlocked
	
   locked
Note: Channel 0 (CH 0) and Channel 1 (CH 1) can 
not be locked.
6 When done selecting the loc ked chan-
nels, press [DISP] to exit the function set-
ting or press [SEL] to change the parental 
lock ON/OFF setting.
OR
To set parental lock ON/OFF:
4 Press  [SEL]  to open lock ON/OFF mode 
after step 3.
5 Turn  [SEL]  to switch between lock ON or 
OFF.
   (Default)
	
   
6 When done selecting the parental loc k 
ON/OFF setting, press [SEL] to exit the 
function setting mode.
OR
To change the parental lock passcode: 
4 Press and hold  [BAND] for more than 2 
seconds after step 3.
   
(New code entry 
mode)
5 Enter a new 4-digit code, then press  [BAND] when finished.
q Press  [d] or [s] to select a number. 
w
 
Press  [BAND] to shift to the right adjacent 
digit. 
 A digit where entr

y is determined is indicated 
as “ *”. 
e
 
Repeat the steps 

q and w to enter a 4-digit 
number. 
6 Repeat step  5  to confirm the new code.
“CODE SET” is displayed for 2 seconds and the 
new code setting is finished, then returns to 
channel locked/unlocked setting display.
Function settings (continued) 
						

							20
 Alarm  Setting
DISPDISP
 Alarm time setting
1 Hold down [ALM] (Alarm) for more than 2 
seconds.
   
(Alarm time 
display)
“ALM ADJ” is displayed when the alarm time is 
not adjusted.
2 Hold down  [ALM] for more than 2 seconds 
after the above display is shown.
 Hour blinks
3 Adjust the hour.
[d] : Sets ahead.
[s] : Sets back.
 Hour entered
4 Push  [ALM].
 Minute blinks
5 Adjust the minute.
[d] : Sets ahead.
[s] : Sets back.
 Minute entered
6 Push [ALM] to complete.
   Completed
The alarm is set to ON automatically after com-
plete alarm time setting.
Alarm indicator (
) lights.
Notes: 
¡  The procedure of alarm time setting under Siri-
usXM radio mode is different with above step 1, 
refer page 18 for its instructions.
¡  When the clock (a  page 9) is not set, perform 
and complete the alarm time setting, the clock 
time will set to “PM 1:00” automatically. Please 
readjust the clock time depending on the actual 
clock time.
¡  Hold  down  [d] or [s] to change numbers 
rapidly.
¡  When you want to readjust the alarm time, repeat 
steps 1 to 6.
Turning ON/OFF the alarm
1 Hold down  [ALM] for more than 2 sec-
onds.
   
(Alarm time 
display)
2 Push  [ALM].
   
(Alarm ON/OFF 
setting)
3 Turn [VOL] (Volume) clockwise or counter-
clockwise to select alarm ON or OFF, then 
push [ALM] again to confi rm the setting.
(Select alarm ON,  lights.)
Notes: 
¡  Before turn ON the alarm, make sure the alarm 
time is set. Failure to heed this will cause invalid 
selection of alarm ON.
¡  Hold  down  [ALM] for more than 2 seconds when 
the alarm is sounding also turns off the alarm.
¡  Access of alarm ON/OFF is available by push 
[ALM] in the “Alarm time display”.
Activating snooze
Press any button on this unit when the alarm 
is sounding.
  
The alarm will sound again in 9 minutes.
Note: If you do not turn the alarm off when the 
alarm is sounding, the alarm sound will shut off af-
ter an hour. (Including the amount of time the alarm 
was postponed (snooze))
 [ALM]
 [VOL]
 [s]/[d]