Panasonic Monitor Bt Lh1760p Owners Manual

31
■COMP. 
Selecting “RGB-COMP.” under “YP
BPR/RGB” in the “INPUT SELECT” menu opens the following menu.
Underlined values indicate factory defaults.
 
*1 “EXECUTING” is displayed during “AUTOSETUP” and “COMPLETE” appears when setup completes. 
“INCOMPLETE” is displayed if setup could not be completed. 
AUTOSETUP may not provide adequate adjustment for some video input. Use H POSITION, V POSITION,
PHASE and CLOCK to adjust.
*2 Each input format can be adjusted but not when user data is loaded (“SETUP...

32
Sets speaker and headphones output. 
Underlined values indicate factory defaults.
*1 When ANALOG is selected in the “INPUT SELECT” menu, the LEVEL METER does not indicate the audio level
even when set to ON. 
AU D IO
Sub menu Settings Description
INPUT
SELECTAU TO
ANALOGSelects speaker and headphones output. 
  When an SDI input line is selected with the [INPUT SELECT] 
button on the front panel: 
embedded audio (SDI terminal)
When input lines other than SDI1 or SDI2 are selected with 
the [INPUT...

33
Main Menu (continued)
Underlined values indicate factory defaults.
*1 Available during HD-SDI input signals.
*2 Available during VIDEO (NTSC) input. Closed captions appear as bright lines on line 21 when closed caption is
set to ON and underscan is also on.
*3 Opens the vector display during SDI signal input.
DISPLAY SETUP
Sub menu Settings Description
WFM/
VECTOROFF
WFM
VECTORSwitches between “WFM/VECTOR” waveform and vector display. 
 Displays waveforms. 
 Displays vector waveforms.*3
POSITION
LB...

34
Main Menu (continued)
Underlined values indicate factory defaults.
*1 The menu can be displayed when the lock is engaged. 
Only “CONTROL/LOCAL ENABLE” menu items are available when the lock is engaged. 
The picture adjusting knob is disabled when the lock is engaged. 
The “LOCAL ENABLE” setting determines operations in lock mode. The volume knob (Jpage 9,  ) can be
used during lock engagement. 
The key mark is displayed during lock engagement. 
*2 Only available when “REMOTE” is selected under...

35
Main Menu (continued)
■ List of setting restrictions ( : available, ×: not available)
*1 The VECTOR display appears only during SDI input.
*2 It does not appear during 1080/23P, 24P, 25P, 29P and 30P input.
InputVIDEOSDI 1/2 YPBPRRGB-VIDEORGB-COMP.DV I - V I D E ODV I - C O M P.CH SD HD SD HD SD HD SD HD
MARKERMARKER××
16:9××
4:3××
BACK××
CENTER××
GPI PRESET1 × ×
GPI PRESET2 × ×
MARKER TYPE × ×
CROSS HATCH
VIDEO 
CONFIGGAMMA SELECT × ×
FILM GAMMA××
COLOR TEMP.
SHARPNESS MODE××
SHARPNESS H × ×...

36
This monitor permits remote operation via GPI/RS-232C terminal. 
GPI screen items correspond to the following terminals. Use the GPI menu to assign functions to each terminal (J page 29). 
Functions assigned to terminals are executed when GND (pin 5) is shor t-circuited (ON) or open (OFF). 
■Operating conditions
Level operation: Operates when GND is short-circuited. 
Edge operation: Operates when GND changes from
open to short-circuited. 
* When level operation is assigned to more than one
terminal,...

37
■Priority of assigned functions
 When both “MARKER1” and “MARKER2” are activated at the same time, “MARKER1” has priority. However,
when the display aspect ratio is 4:3, the “MARKER1” aspect ratio is 16:9 and the “MARKER2” aspect ratio is 4:3,
“MARKER2” is displayed. In this case, the “MARKER2” background is controlled. 
 When “MARKER BACK HALF” and “MARKER BACK BLACK” are activated at the same time, “MARKER BACK
BLACK” has priority. 
 During GPI edge operation and two or more of “INPUT SEL. VIDEO”,...

38
■Setting command
No Command Description Data Response
1IIS Input switch 0: SDI1  1: SDI2  2: VIDEO
3: YP
BPR/RGB 6: DVI-DIIS
2VPC Image quality 
adjustment CON00-60 : Contrast settings
BRI00-60 : Brightness settings
CRO00-60 : Chroma settings
PHA00-60 : Phase settingsVPC
3
OBO Blue only 0: OFF  1: ON OBO
4OHV HV Delay 0: OFF  1: H DELAY  2: V DELAY 
3: HV DELAYOHV
5
VBL Backlight 00-60: Backlight setting VBL
6
DCH Cross hatch 0: OFF 1: LOW 2: HIGH DCH
7
DSD Status display 0: CONTINUE  1: 3SEC OFF  2:...

39
REMOTE Specifications (continued)
■Query command
*1 When both 16:9 and 4:3 markers are displayed, the 16:9 marker state is returned.
No Command Description Data Response
1QIS Input selection 0: SDI1 1: SDI2 2: YP
BPR3: RGB-VIDEO 4: VIDEO 6: RGB-COMP.
9: DVI-VIDEO 10: DVI-COMP.
2QPC Image quality 
adjustment CON : Contrast setting value 00-60
BRI : Brightness setting value00-60
CRO : Chroma setting value 00-60
PHA : Phase setting value 00-60
3
QBO
Blue only0: OFF  1: ON
4
QBL
Backlight00-60
5
QCH
Cross...

40
How to Attach the Rack Mount
The monitor can be fitted with an optional BT-MA1710G rack mount adaptor to enable mounting it in a standard 19-
inch rack (7U size height). The steps below show how to attach it. 
1. Remove the three screws on the back and base
of the monitor and remove the stand.2. Use the supplied screws to attach the rack
mount adaptors to both sides of the monitor. 
Maintenance Inspections
Maintenance inspections through periodic and appropriate maintenance are essential to keep the...