Panasonic Monitor Bt Lh1760p Owners Manual

11
1. Attach the power cord to the monitor unit.
2. Connect the power cord to the power outlet.■When using external DC power (12V DC)
You can slide open the power cover, and switch from
AC input to external DC input. (When shipped from
the factory, the power cover is up, and AC input is
selected.)
Please note the followings
 If the power cover has been removed or opened, do
not use the monitor with the power supply connected
to both the AC input and external DC input terminals.
 Use a shielded DC cable...

12
The screen displays eight types of information: input signal status, picture adjusting knob status, sharpness display,
FUNCTION display, audio level meter display, menu display, time code display and closed caption display.
1. The selected input line (Jpage 9,  )
VIDEO, SDI1, SDI2, 
YP
BPR/RGB-VIDEO/RGB-COMP.
DV I - V I D E O / DV I - C O M P.
2. Signal format

Use “STATUS DISPLAY” in the “SYSTEM CONFIG” 
menu to set the display status (
J page 22).
“UNSUPPORT SIGNAL” appears if an unsupported 
signal...

13
How to Use the On Screen Menu (continued)
Use the menu to open and set up functions. 
When “FUNCTION DISPLAY” (Jpage 23) is set to
ON, press any of the “FUNCTION1” to
“FUNCTION5” buttons to display the functions
assigned to the FUNCTION buttons. 
This display disappears after 2 seconds of inaction. 
“XXXXX” indicates operating status (Jpage 25,
“Functions displayed during FUNCTION button
operation”).
A white skeleton bar meter indicates the audio level
for SDI signals. 
You can switch the level...

14
How to Use the On Screen Menu (continued)
Use the menu to display the time code for HD-SDI
signal input. It also allows you to switch display mode
(VITC, LTC, VUB, LUB).
In VITC and LTC display mode: 
Displays the time code in hours: minutes: seconds:
or frames.
In drop-frame mode, a different delimiter between
seconds and frames is used.
Note: 
Read errors are displayed as “--:--:--:--” 
In VUB and LUB display modes: 
BG8, BG7, BG6, BG5, BG4, BG3, BG2, BG1 appear
in the stated order. BG: binary...

15
1. Press [MENU] to display the MAIN menu. 
2. Press [ ,  ] to select a menu and press
[ENTER].3. Press [ ,  ] to select a sub menu and Press
[ENTER].
The settings in the sub menu change to green. 
4. Press [ ,  ] to select a setting, then press
[ENTER]. 
To cancel, press [MENU]. 
To return to the previous screen
Push [MENU].
Menu operations
[MAIN MENU]
How to Use the On Screen Menu (continued) 

16
You can save and load up to five combinations of menu settings and adjustments made with the picture adjustment
knob as user data. You can also return settings and adjustments to their factory defaults.
User data include the following settings. 
 Menu settings except “SETUP LOAD/SAVE” (including button function settings on the monitor front panel)
 Screen adjustments made with the picture adjusting knob
1. Press [MENU] to display the MAIN menu. 
2. Press [ ,  ] to select the “SYSTEM CONFIG”
menu and...

17
Menu configuration
MAIN MENU
VIDEO CONFIG
SYSTEM CONFIG
FUNCTION
INPUT SELECT GPI
MARKER
GAMMA SELECT 
FILM GAMMA
COLOR TEMP.
SHARPNESS MODE
SHARPNESS H
SHARPNESS V
I-P MODE
MONO
ANAMO
SD ASPECT
SCAN CONT./BACK.
BACKLIGHT
SUB WINDOW
MENU POSITION
STAT US DISPLAY
SETUP LOAD
SETUP SAV E
POWER ON SETUP
COLOR SPA C E
POWER SAVE MODE
BLACK DATA INSERTION
GPI CONTROL
GPI1
GPI2
GPI3
GPI4
GPI5
GPI6
GPI7
GPI8 VIDEO
NTSC SETUP
YP
BPR/RGB
COMPONENT LEVEL
SELECT SYNC
COMP.
DV I - D
AUTOSETUP
H POSITION
V...

18
Underlined values indicate factory defaults.
*1 This setting is turned “ON” when receiving marker control in REMOTE operation. (GPI, if set, has priority.)
*2 These settings are disabled when the GPI function (Jpage 36) is used to control the marker setting. 
They are also disabled in split screen mode. 
*3 This setting is enabled only for HD and SD signal input in 16:9 aspect ratio mode. 
*4 This setting is enabled for SD signal input in 4:3 aspect ratio mode. 
*5 Remote control via RS-232C ends in...

19
■16:9 marker
(Displayed for HD input and SD input in 16:9 ratio
mode.) 
This marker is only displayed as a vertical bar. The
 section becomes the “MARKER BACK”. 
VISTA marker, CNSCO marker
This marker is displayed as a horizontal dotted line. 
The marker is displayed as a vertical dotted line
when “UNDER” is selected under “SCAN” in the
“VIDEO CONFIG” menu. 
Area marker
This marker is displayed as a dotted line. ■4:3 marker
(Displayed for SD input in 4:3 aspect ratio mode)
 This marker is displayed as...

20
Underlined values indicate factory defaults.
*1 In split-screen display, changes are not reflected to the still image in the main window. 
*2 These functions are not available when “RGB-COMP.” under “YP
BPR/RGB” or “DVI-COMP.” under “DVI-D” is
selected in the “INPUT SELECT” menu (Jpage 30).
*3 The following sharpness values are available and the settings for the selected input signal is displayed.
Adjustment status during selection appears at the bottom right of the screen. 
1) VIDEO system input...