Panasonic Memory Card Portable Recorder Player Ajhpm110p Operating Instructions

Setup: Item Settings121
 Setup
007 CHARA H-POS0000
|0004
|
00160
|
4
|
16Specifies the horizontal character position output via the VIDEO MON connector or 
displayed in the superimposed display of the LCD panel.
008 CHARA V-POSWhen set to 59.94 Hz, 
23.98 Hz, 24 Hz, 
29.97 Hz, 59-23 Hz, 
60-24 HzSpecifies the vertical character position output via the VIDEO MON connector or 
displayed in the superimposed display of the LCD panel.
0000
|
0020
|
00220
|
20
|
22
When set to 50 Hz, 
25 Hz, 60-25 Hz
0000
|...

122Setup: Item Settings ■Recording Format Comparison Table
The table below shows the relationship between setup menu No. 25 SYSTEM FREQ, No. 020 SYS FORMAT and No. 025 REC 
FMT settings and recording formats.
Setup menu settingRecording format
No.25: SYSTEM FREQNo.020: SYS FORMATNo.025: REC FMT(HD)
DVCPROAVC-Intra50/100
59.941080i 1080/59.94i 1080/59.94i
720p 720/59.94p 720/59.94p
480i 480/59.94i ---
501080i 1080/50i 1080/50i
720p 720/50p 720/50p
576i 576/50i ---
23.98 --- --- 1080/23.98p
24 --- ---...

Setup: Item Settings123
 Setup
032 REC REF
0000
0001
NORMAL
SLTC
Specifies the reference to synchronize the frames for recording.
0: The input video signal is automatically identified and serves as reference.
1: The time code which is input to the SD I IN connector is identified and serves as 
reference.
NOTE:
When the SLTC is selected, the following settings are necessary to validate the settings 
for this item:
 Setup menu No. 25 SYSTEM FREQ: 59.94
 Setup menu No. 020 SYS FORMAT: 720p
 VIDEO INPUT...

124Setup: Item Settings
◆NOTE: 
 The clock is accurate to within about ±30 seconds a month with the 
power off. 
 When the precise time is required, check and reset the time while 
the power is on.  05 TIME ZONE
0000
0001
|
0018
|
0027
|
0050
00:00
+00:30
|
+09:00
|
–12:00
|
–00:30Sets the time difference from the world standard time. Use the table below for reference 
in setting the time.
Time differenceCity/Region
00:00 Greenwich
+00:30
+01:00 Central Europe
+01:30
+02:00 Eastern Europe
+02:30
+03:00...

Setup: Item Settings125
 Setup
This menu allows you to set method for engaging search dial operations, maximum shuttle speed operation, maximum speed 
of FF and REW operation, NEXT and PREV seek operations, display of warning messages when REF.VIDEO is not connected, 
PLAY delay time, battery type, display of warnings when power is too low, voltage when the power supply is turned off. 
* An underlined  setting
 indicates an initial value.
OPERATION
ItemSetting
Settings and brief function descriptionFR...

126Setup: Item Settings
155 AUTO REC
0000
0001
0002
OFF
TYPE1
TYPE2Select whether recording and stopping should be performed automatically according to 
the Recording Marks in the HD SDI input signals from Panasonic camera-recorders. 
0: No automatic recording/stopping 
1: Recording and stopping is performed automatically according to the Recording Marks 
in the LTC information attached to HD SDI signals. 
2: Recording and stopping is performed automatically according to the Recording Marks 
in the SVITC...

Setup: Item Settings127
 Setup
Panasonic camera-recorders, recording formats and Recording Mark
*1: Recording Marks are not added to the HD SDI signal in default mode. 
This menu specifies the ID data that will be returned to the controller. 
* An underlined setting
 indicates an initial value.
184 TYPE-B END0000
|0018
|
003410.6
|
12.4
|
14.0Specifies the voltage (in 0.1 V steps) when this unit will automatically power off because 
the voltage of a TYPE-B battery selected in menu No. 180 BATTERY SEL...

128Setup: Item Settings This menu sets the time code. 
* An underlined setting
 indicates an initial value.
TIME CODE
ItemSetting
Settings and brief function descriptionFR
No.SUPER
DISP.FR
No.SUPER 
DISP.
500 VITC BLANK0000
0001
BLANK
THRUSpecifies whether or not a VITC signal will be output at the positions selected in menu No. 
501 VITC POS-1 and No. 502 VITC POS-2 during playback. 
0: VITC signals are not output.
1: VITC signals are output.
NOTE: 
 This setting is available only during analog...

Setup: Item Settings129
 Setup
507 EXT TC SEL
0000
0001
0002
EXT_L
SLTC
SVITCSpecifies the time code used when an external time code is used. 
0: LTC of the TIME CODE IN connector
1: LTC data attached to serial signal input to HD SDI IN
2: VITC data attached to serial signal input to HD SDI IN
NOTE: 
When SLTC and SVITC are set, the VITC in the input video signal is used when an 
analog composite or SD SDI input signal is selected. When 1394 is selected as the 
input signal, the IEEE 1394 digital input...

130Setup: Item Settings Definition of terms: 
This menu is used for video settings. 
* An underlined setting
 indicates an initial value.
518 VITC GEN
0000
0001
OFF
ON
Specifies whether or not the internal time code generator value should be recorded in the 
VAUX area.
0: The internal time code generator value is not recorded.
Record the time code value when it is superimposed on input video signals. 
1: The internal time code generator value is recorded.
NOTE: 
 When 1394 is selected as the input...