Panasonic Memory Card Camera Recorder Ajhpx3700g Operating Instructions

							171Menu: Menu Description Tables
Menu
Items/
Data SavedAdjustable 
RangeRemarks
USR SW F.RATE (1080-59.94i, 
1080-23.98PsF, 
1080-24PsF)
1FRAME
:
24FRAME
:
30FRAME
(1080-50i)
1FRAME
:
25FRAME
When the FRATE function has been 
assigned to a user button, the starting 
frame rate under VFR operation is set.
When the mode has been changed 
using other settings and the frame rate 
value set here exceeds the maximum 
frame rate allowed by the set mode, the 
maximum frame rate is changed to the 
maximum frame rate of the set mode.
SCUFR
SCAN REVERSE ON
OFFThis setting is for correcting an image 
which has been inverted by a film-use 
lens or anamorphic lens attached to the 
unit.
SCUF R
PC MODE SEL USB HOSTUSB DEV.This is for setting the operations mode of 
this unit when PC MODE is set to “ON” 
and an external device is connected to 
the USB connector.
USB HOST:
Allows data transfer from the unit 
to the USB-connected device.
USB DEV.:
Allows data transfer from the 
USB-connected device to the 
unit.

						

							172Menu: Menu Description Tables
* This variable range is the numerical values for 59.94 Hz. For 
50 Hz, the frame rate is up to 24f. The frame rate is up to 23f in 
24PN (Native) mode.

						

							173Menu: Menu Description Tables
Menu
OUTPUT SEL
Items/
Data SavedAdjustable 
RangeRemarks
SIGNAL 
FORMAT4:2:24:4:4Select the signal that is output from the 
HD SDI A · B connectors.
4:2:2:YP
BPR 4:2:2 format is selected.
4:4:4:RGB 4:4:4 format is selected. 
LINK A will be output from the 
HD SDI A connector, and LINK B 
from the HD SDI B connector.
–CUF –
P-10LOG ON
OFFON:P-10LOG format signal is output. 
This is valid when GAMMA 
MODE SEL is set to “FILM-
REC”, and SIGNAL FORMAT is 
set to “4:4:4”.
OFF:Signal format set in GAMMA 
MODE SEL is output.

						

							174Menu: Menu Description Tables
HD SDI A · B OUT MARKER
Items/
Data SavedAdjustable 
RangeRemarks
MARKER SW OFFA
B
BOTHSwitches the marker on and off.
OFF:The characters are not 
superimposed.
A:The characters are 
superimposed on the HD SDI A 
connector.
B:The characters are 
superimposed on the HD SDI B 
connector.
BOTH:The characters are 
superimposed on the HD SDI A 
connector and the HD SDI B 
connector.
–CUFR
CENTER MARK OFF
1
2
3
4
Switch the center mark.
OFF:Do not display center mark.
1:+ (large)
2:Hollow (large)
3:+ (small)
4:Hollow (small)
–CUFR
SAFETY MARK OFF
1
2Select the frame type for the safety zone.
OFF:Do not display frame.
1:Box
2:Corner frame
–CUFR
SAFETY AREA 80%
:
90%
:
100%
For setting the size of the safety marker.
It is possible to set the size by units of 
1% with a fixed ratio between of width 
and height.
–CUFR
FRAME MARK ON
OFFSet the frame marker to “ON” or “OFF”.
–CUFR
Items/
Data SavedAdjustable 
RangeRemarks
FRAME SIG 4:313:9
14:9
VISTA
CNSCOSet the frame marker.
The VISTA ratio is 16:8.65.
The CNSCO ratio is 16:6.81.
–CUFR
USER BOX ON
OFFFor setting whether to include the user 
box in the signal from the HD SDI A · B 
connector.
–CUFR
USER BOX 
WIDTH1
:
13
:
100
For setting the width of the user box.
–CUFR
USER BOX 
HEIGHT1
:
13
:
100
For setting the height of the user box.
–CUFR
USER BOX H 
POS–50
:
+00
:
+50
For setting the horizontal position of the 
user box center.
–CUFR
USER BOX V 
POS–50
:
+00
:
+50
For setting the vertical position of the 
user box center.
–CUFR
AJ-HPX3700G-VQT1V68_eng.book  174 ページ  ２００８年１０月１５日　水曜日　午後６時３８分 
						

							175Menu: Menu Description Tables
Menu
MONI OUT MARKER
Items/
Data SavedAdjustable 
RangeRemarks
CENTER MARK OFF
1
2
3
4
Switch the center mark.
OFF:Do not display center mark.
1:+ (large)
2:Hollow (large)
3:+ (small)
4:Hollow (small)
–CUFR
SAFETY MARK OFF
1
2Select the frame type for the safety zone.
OFF:Do not display frame.
1:Box
2:Corner frame
–CUFR
SAFETY AREA 80%
:
90%
:
100%
For setting the size of the safety marker.
It is possible to set the size by units of 
1% with a fixed ratio between of width 
and height.
–CUFR
FRAME MARK ON
OFFSet the frame marker to “ON” or “OFF”.
–CUFR
FRAME SIG 4:313:9
14:9
VISTA
CNSCOSet the frame marker.
The VISTA ratio is 16:8.65.
The CNSCO ratio is 16:6.81.
–CUFR
USER BOX ON
OFFFor setting whether to include the user 
box in the signal from the MON OUT 
connector.
–CUFR
USER BOX 
WIDTH1
:
13
:
100
For setting the width of the user box.
–CUFR
USER BOX 
HEIGHT1
:
13
:
100
For setting the height of the user box.
–CUFR
USER BOX H 
POS–50
:
+00
:
+50
For setting the horizontal position of the 
user box center.
–CUFR
USER BOX V 
POS–50
:
+00
:
+50
For setting the vertical position of the 
user box center.
–CUFR
LCD MONITOR
Items/
Data SavedAdjustable 
RangeRemarks
BRIGHTNESS –7
:
+0
:
+7
Adjust the LCD monitor brightness.
–CUF –
COLOR LEVEL –7
:
+0
:
+7
Adjust the LCD monitor chroma level.
–CUF –
CONTRAST –7
:
+0
:
+7
Adjust the LCD monitor contrast.
–CUF –
BACKLIGHT NORMALHIGHAdjust the backlight.
NORMAL:
Mode normally used
HIGH:This is brighter than NORMAL.
–CUF –
SELF SHOOT NORMAL
MIRRORSelect whether or not to change the LCD 
monitor to mirror image.
NORMAL:
Do not change to mirror image.
MIRROR:
Change to mirror image.
–CUF –
AJ-HPX3700G-VQT1V68_eng.book  175 ページ  ２００８年１０月１５日　水曜日　午後６時３８分 
						

							176Menu: Menu Description Tables
GENLOCK
Items/
Data SavedAdjustable 
RangeRemarks
GENLOCK INTEXTSwitch the camera synchronizing signal.
INT:Synchronize with the internal 
reference signal regardless of 
the reference signal input to the 
GENLOCK IN connector.
EXT:Synchronize with the reference 
signal input to the GENLOCK IN 
connector.
–CUFR
GL PHASE HD SDICOMPOSITFor selecting the output signals that lock 
phases to the signals that are input in the 
GENLOCK IN connector. Note, however, 
that in 1080/23.98PsF mode and 1080/
24PsF mode, the phase is locked to HD 
SDI even if “COMPOSIT” has been 
selected.
HD SDI:
For locking the HD SDI output 
signals to the GENLOCK input.
For the down converter output 
signals, the start position of the 
video delays by about 90 lines.
COMPOSIT:
For locking the down converter 
output signals to the GENLOCK 
input.
For the HD SDI output signals, 
the start position of the video 
gains by about 90 lines.
–CUFR
H PHASE 
COARSE–100
:
+000
:
+100
Perform coarse phase adjustment for 
horizontal hold when configuring a 
system.
–––––
H PHASE FINE –100
:
+000
:
+100
Perform fine phase adjustment for 
horizontal hold when configuring a 
system.
–––––
AJ-HPX3700G-VQT1V68_eng.book  176 ページ  ２００８年１０月１５日　水曜日　午後６時３８分 
						

							177Menu: Menu Description Tables
Menu
The ____ in the Adjustable Range column indicates the preset mode.
* If the remote control unit is connected, settings made from the 
menu are disabled. (The set value is displayed.)
PA I N T
RB GAIN CONTROL
Items/
Data SavedAdjustable 
RangeRemarks
R GAIN AWB 
PRE*–200
:
+000
:
+200
For setting the Rch gain when the 
WHITE BAL switch is in the [PRST] 
position.
SCUFR
B GAIN AWB 
PRE*–200
:
+000
:
+200
For setting the Bch gain when the 
WHITE BAL switch is in the [PRST] 
position.
SCUFR
R GAIN AWB A* –200
:
+000
:
+200
For setting the Rch gain when the 
WHITE BAL switch is in the [A] position.
SCUFR
B GAIN AWB A* –200
:
+000
:
+200
For setting the Bch gain when the 
WHITE BAL switch is in the [A] position.
SCUFR
R GAIN AWB B* –200
:
+000
:
+200
For setting the Rch gain when the 
WHITE BAL switch is in the [B] position.
SCUFR
B GAIN AWB B* –200
:
+000
:
+200
For setting the Bch gain when the 
WHITE BAL switch is in the [B] position.
SCUFR
AWB A GAIN 
OFFSET*ON
OFFFor setting the values of the Rch gain 
and the Bch gain when the auto white 
balance is executed as the WHITE BAL 
switch is in the [A] position.
ON:To retain the values set in the 
items of R GAIN AWB A and B 
GAIN AWB A
OFF:The values of the Rch gain and 
the Bch gain is set to “0”.
SCUFR
AWB B GAIN 
OFFSET*ON
OFFFor setting the values of the Rch gain 
and the Bch gain when the auto white 
balance is executed as the WHITE BAL 
switch is in the [B] position.
ON:To retain the values set in the 
items of R GAIN AWB B and B 
GAIN AWB B
OFF:The values of the Rch gain and 
the Bch gain is set to “0”.
SCUFR
RGB BLACK CONTROL
Items/
Data SavedAdjustable 
RangeRemarks
MASTER PED* –200
:
+000
:
+200
For setting the level of the master 
pedestal.
SCUFR
R PEDESTAL* –100
:
+000
:
+100
For setting the pedestal level of the Rch.
SCUFR
G PEDESTAL* –100
:
+000
:
+100
For setting the pedestal level of the Gch.
SCUFR
B PEDESTAL* –100
:
+000
:
+100
For setting the pedestal level of the Bch.
SCUFR
PEDESTAL 
OFFSET*ON
OFFFor setting the pedestal levels of the 
Rch, the Gch and the Bch when the auto 
black balance is adjusted.
ON:To retain the values set in the 
respective items of R 
PEDESTAL, G PEDESTAL, and 
B PEDESTAL
OFF:The pedestal levels of the Rch, 
the Gch and the Bch are set to 
“0”.
SCUF –
R FLARE* –100
:
+000
:
+100
For adjusting the flare level of the Rch. 
Adjustment values in this item are added 
to the flare adjustment value that is 
adjusted on  screen.
SCUFR
G FLARE* –100
:
+000
:
+100
For adjusting the flare level of the Gch. 
Adjustment values in this item are added 
to the flare adjustment value that is 
adjusted on  screen.
SCUFR
B FLARE* –100
:
+000
:
+100
For adjusting the flare level of the Bch. 
Adjustment values in this item are added 
to the flare adjustment value that is 
adjusted on  screen.
SCUFR
AJ-HPX3700G-VQT1V68_eng.book  177 ページ  ２００８年１０月１５日　水曜日　午後６時３８分 
						

							178Menu: Menu Description Tables

						

							179Menu: Menu Description Tables
Menu

						

							180Menu: Menu Description Tables yWhen shooting with the MASTER GAIN set to “–3dB”, 
coloring phenomena may occur in portions of the video 
with high brightness.
The coloring phenomena can be reduced by switching the 
OUTPUT/AUTO KNEE switch to [CAM/AUTO KNEE 
OFF], setting the MANUAL KNEE menu option of the 
 screen to “ON”, and then changing the 
following menu options.
– When “HD”, “SD”, “FILMLIKE1”, “FILMLIKE2” or 
“FILMLIKE3” has been selected in the GAMMA MODE 
SEL menu option of the  screen, reduce the 
value in the KNEE MASTER SLOPE menu option of the 
 screen.
– When “FILM-REC” has been selected in the GAMMA 
MODE SEL menu option of the  screen, 
reduce the value in the F-REC DYNAMIC LVL menu 
option of the  screen.
– When “VIDEO-REC” has been selected in the GAMMA 
MODE SEL menu option of the  screen, 
reduce the value in the V-REC KNEE SLOPE menu 
option of the  screen.
MID SETTING
Items/
Data SavedAdjustable 
RangeRemarks
„MASTER GAIN –3dB
:
3dB
:
30dB
Select the master gain from –3, 0, 3, 6, 
9, 12, 15, 18, 21, 24, 27, or 30 dB.
SCUF –
H.DTL LEVEL 00
:
08
:
63
For performing the horizontal detail 
correction level setting.
SCUF –
V.DTL LEVEL 00
:
12
:
31
For performing the vertical detail 
correction level setting.
SCUF –
DTL CORING 00
:
12
:
60
For performing the noise elimination 
level setting for detail.
SCUF –
H.DTL FREQ. 00
:
18
:
31
For performing the horizontal detail 
frequency selection.
SCUF –
LEVEL DEPEND. 0
1
:
5
For setting the LEVEL DEPEND.
When the Y-detail is emphasized, details 
of dark sections are compressed.
If the numerical value is larger, details of 
bright sections are also compressed.
SCUF –
MASTER 
GAMMA0.30
:
0.45
:
0.75
For setting the master gamma. (0.01 
step)
SCUF –
BLACK GAMMA –8
:
OFF
:
+8
For setting the gamma curve for the dark 
portion.
–8 to –1:
The dark portion is compressed.
OFF:Standard state
+1 to +8:
The dark portion is extended.
SCUF –
B.GAMMA 
RANGE12
3For setting the upper limit of 
compression/expansion.
1:Approximately 20%
2:Approximately 30%
3:Approximately 40%
SCUFR
„MATRIX 
TABLEOFF
A
B
For selecting the color correction table 
for the linear matrix.
SCUF –
„COLOR 
CORRECTON
OFFFor switching on/off of the 12-axis 
independent color correction.
SCUF –
AJ-HPX3700G-VQT1V68_eng.book  180 ページ  ２００８年１０月１５日　水曜日　午後６時３８分