Panasonic Memory Card Camera Recorder Ajhpx3700g Operating Instructions

							111Adjustments and Settings for Recording: Cinematograph Settings
Adjustments and Settings for Recording
USER MENU
Page Factory settingCinematograph 
setting
USER 
MENU1SYSTEM MODE SYSTEM MODE
OUTPUT SEL OUTPUT SEL
MASTER PED
BLACK GAMMA (LOW)
BLACK GAMMA (LOW)B.GAMMA RANGE (LOW)
MASTER GAMMA MASTER GAMMA
F-REC DYNAMIC LVL GAMMA MODE SEL
F-REC BLACK STR LVL F-REC DYNAMIC LVL
DETAIL F-REC BLACK STR LVL
USER MAIN SW DETAIL
USER1 SW SIDE SW LOCK
USER2 SW COLOR TEMP PRE
MARKER SEL SD CARD READ/WRITE
TEXT MEMO SW SCENE
SIDE SW LOCK
USER 
MENU2SD CARD READ/WRITE No page display
SCENE
USER 
MENU 
(SYS)REC FUNCTION REC FUNCTION
BRIGHTNESS (LCD) BRIGHTNESS (LCD)
COLOR LEVEL (LCD) COLOR LEVEL (LCD)
CONTRAST (LCD) CONTRAST (LCD)
BACKLIGHT (LCD) BACKLIGHT (LCD)
BATTERY SELECT BATTERY SELECT
FRONT VR CH1 FRONT VR CH1
FRONT VR CH2 FRONT VR CH2
FIRST REC TC FIRST REC TC
HOURS METER HOURS METER
AJ-HPX3700G-VQT1V68_eng.book  111 ページ  ２００８年１０月１５日　水曜日　午後６時３８分 
						

							11 2Adjustments and Settings for Recording: RGB 4:4:4 Output and P-10LOG Settings This unit can output signals suitable for Digital-Intermediate, 
which is a film production workflow.
Link A signal is output from the HD SDI A connector and 
Link B signal is output from the HD SDI B connector by 
performing the cinematograph setting, and it is possible to 
set these signals as P-10LOG for RGB 4:4:4 output. For 
cinematograph settings, see page 109 and later.
Refer to the following procedures to set the above without 
using the cinematograph setting.
1Open the  screen from the PAINT page with 
menu operation.
2Select GAMMA MODE SEL using the JOG dial button, 
and press the JOG dial button.
3Turn the JOG dial button and select “FILM-REC”, then 
press the JOG dial button.
4Open  screen from SYSTEM SETTING 
page with menu operation.
5Select SIGNAL FORMAT using the JOG dial button, and 
press the JOG dial button.
6Turn the JOG dial button and select “4:4:4”, then press 
the JOG dial button.
7Select P-10LOG using the JOG dial button, and press 
the JOG dial button.
8Turn the JOG dial button and select “ON”, then press 
the JOG dial button.
9Press the MENU button to complete the menu 
operation.

						

							Preparation
11 3Preparation: Power Supply
Preparation
A battery pack or an external DC power supply can be used as the unit’s power supply.
Battery packs from the following manufacturers can be used:
yAnton/Bauer
yIDX
yPA C O
ySony
The type of the battery can be checked or changed through 
the menu screen on the viewfinder or on the monitor.
yPressing the MODE CHECK button on the side of the unit 
displays the current type of the battery in the upper right 
corner of the viewfinder display.
yNavigate the menu to open the  
screen from the MAIN OPERATION page. Then, through 
the BATTERY SELECT menu option, you can check and 
change the battery type.

						

							11 4Preparation: Power Supply
1Mount the Anton/Bauer battery pack.
a.Power supply output connector for lighting
b.Anton/Bauer battery pack
c.Lighting control switch

The Anton/Bauer battery holder includes both a power 
supply output connector for lighting and a lighting control 
switch, which are convenient when attaching a light. Please 
contact Anton/Bauer for information about the lighting 
system.
2Insert the battery and slide it in the direction of the 
arrow.
d.Release lever

Removing the battery pack
Completely push down and hold the release lever on the 
battery holder. Then, slide the battery pack in the 
opposite direction to the arrow while holding the lever 
down.
3Setting the battery type.
Select the battery type listed under BATTERY SELECT. 
Select BATTERY SELECT from the  screen on the MAIN OPERATION page.
Please refer to [BATTERY SETTING1] (page 196) for 
more information.
The following Anton/Bauer batteries can be used:
yPROPAC14
yTRIMPAC14
yHYTRON50
yHYTRON140
yDIONIC90
yDIONIC160
Mounting the Battery and Setting the Battery Type
Using an Anton/Bauer Battery Pack
ab
c
d
AJ-HPX3700G-VQT1V68_eng.book  114 ページ  ２００８年１０月１５日　水曜日　午後６時３８分 
						

							11 5Preparation: Power Supply
Preparation
1Remove the battery holder.
2Mount the NP-1 type battery case on the unit.

						

							11 6Preparation: Power Supply
1Connect the external DC power supply to the DC IN 
socket on the unit.
2Turn on the power switch of the external DC power 
supply. (If the power switch is available on the external 
DC power supply.)
3Turn on the POWER switch on the unit.

						

							11 7Preparation: Mounting the lens and Performing the Flange Back and White Shading Adjustments
Preparation
1Raise the lens clamping lever and remove the mount 
cap.
a.Lens clamping lever
b.Mount cap
2To mount the lens, align the indentation at the top center 
of the lens mount with the center mark of the lens.
c.Mark
3Lower the lens clamping lever to clamp the lens.
4Secure the cable through the cable clamp, and plug it 
into the LENS connector.
d.LENS connector
5Adjust the lens flange back.

						

							11 8Preparation: Mounting the lens and Performing the Flange Back and White Shading Adjustments
8Repeat steps 5 to 7 until the lens is in focus at both the 
telephoto and wide-angle positions.
9Firmly tighten the F.f ring clamping screw.
Method to correct the waveform to be more flat by 
combining the sawtooth-shaped waveform and the 
parabola waveform when watching the respective 
waveforms of R, G and B of the video signals.

						

							11 9Preparation: Mounting the lens and Performing the Flange Back and White Shading Adjustments
Preparation
When making the white shading correction, make the 
adjustment while observing the R, G, and B waveforms in 
the horizontal and vertical directions with the waveform 
monitor.
This now completes the white shading adjustments.
The adjustment values are now stored in the non-volatile 
memory so that even when the unit’s power is turned off, 
there will be no further need to perform the white shading 
adjustment.
AJ-HPX3700G-VQT1V68_eng.book  119 ページ  ２００８年１０月１５日　水曜日　午後６時３８分 
						

							120Preparation: Preparing for Audio Input Take the following steps to prepare the camera for connecting audio input devices.
The unit can be equipped with the AJ-MC900G stereo 
microphone kit (optional).
1Open the microphone holder.
2Mount the microphone and tighten the clamping screw. 
The microphone must be attached with the UP mark on 
the microphone facing up.
a.Clamping screw
3Connect the microphone cable to the MIC IN jack on the 
camera.
b.MIC IN jack
4Set the AUDIO IN switch to [FRONT] depending on the 
audio channel to be recorded.
c.AUDIO IN switch
1Remove the cover to insert the wireless receiver and 
secure it with the screws.
2Set the AUDIO IN switch to [W.L.] depending on the 
audio channel to be recorded.
3When using a 2-channel wireless receiver, select 
“DUAL” in the WIRELESS TYPE menu option. The 
menu option WIRELESS TYPE can be found in the 
 screen on the MAIN OPERATION 
page.
Preparing for Audio Input
When Using the Front Microphone
a
b
c
When Using a Wireless Receiver
When Using the Unislot Wireless Receiver
AJ-HPX3700G-VQT1V68_eng.book  120 ページ  ２００８年１０月１５日　水曜日　午後６時３８分