Panasonic Memory Card Camera Recorder Ajhpx3000g Operating Instructions

							161Menu : Menu Description Tables
 Menu
*1 This variable range is the numerical values for 59.94 Hz. For 
50 Hz, the frame rate is up to 24f. The frame rate is up to 23f 
in 24PN (Native) mode.
The ____ in the Adjustable Range column indicates the
preset mode. 
×Note
Displayed REC TIME, PAUSE TIME and TOTAL REC TIME
are translated into either drop-frame or non-drop-frame
according to the mode of operation.
TAKE TOTAL TIME is actual time. Therefore, TOTAL REC
TIME may incorporate fractions, depending on the settings.
REC FUNCTION
Items/
Data Saved Adjustable 
Range
 Remarks 
INTERVAL 
REC MODEON
ONE SHOT
OFFSets INTERVAL REC function.
ON:Uses internal memory to perform 
interval recording.
ONE SHOT:
Performs “one-shot” recording for the 
duration specified under REC TIME, 
and then stops.
OFF: INTERVAL REC is not performed.
‹Note
This item cannot be changed when “ON” 
is selected in LOOP REC MODE.–CUF –
INTERVAL 
REC HOLDON
OFFSelects whether INTERVAL REC MODE 
settings are retained or not when the 
power is turned off once.
ON:
RetainOFF:Do not retain. The INTERVAL REC 
MODE is OFF whenever the power 
is turned on again.
–CUF –
REC TIME*100s01f : 
59s29fSet REC TIME (1 cut).
‹Note
However, the settings can be made 
frame by frame, and the numbers of the 
cut-off unit frames for the shortest time 
period and the set time on the actual 
operation may vary with the recording 
method. For details, refer to [Interval 
Recording] (page 37).
–CUF –
PAU S E  T I M E *100h00m00s01f : 00h04m59s29f : 23h59m59s29f
Specify PAUSE time for recording.
‹Note
However the settings can be made frame 
by frame, and the numbers of the cut-off 
unit frames for the shortest time period 
and the set time on the
 actual operation 
may vary with the recording method. For 
details, refer to [Interval Recording] 
(page 37).
–CUF –
TA K E  T O TA L  
TIMENONE : 
5daySpecify the time needed for shooting.
Select from NONE (continue until 
operation is manually stopped) to 5 days.
–CUF –
TOTAL REC 
TIME*100m00s01f
 : 
99m59s29f
OVER100min
NONEDisplay total recorded time. The setting 
cannot be changed using this option. 
Displays the recording time (recording 
time needed for the P2 card) calculated 
using REC TIME, PAUSE TIME, and 
TA K E  T O TA L  T I M E .
‹Note
A value based on actual processing is 
displayed
.–––––
AU DIO  R EC O N
OFFSelect whether or not sound will be 
recorded.
–CUF –
START DELAY 0SEC : 
10SECSet the delay after pressing REC START 
to start recording in INTERVAL REC.
–CUF –
PRE REC 
MODEON
OFFSelect whether or not to enable PRE-
RECORDING.
ON:PRE-RECORDING enabled.
OFF:PRE-RECORDING disabled.
‹Note
Specify the PRE-RECORDING time by 
using the menu option PRE REC TIME.
–CUF –
Items/
Data Saved Adjustable 
Range
 Remarks 
PRE REC 
TIME1SEC
 : 
8SECSet PRE-RECORDING. 
1-8SEC:
Set the length of time that can be 
retrospectively recorded before the 
REC START button is pressed. 
–CUF–
LOOP REC 
MODEON
OFFSelect whether or not to enable LOOP 
REC. 
This setting can be used with PRE-
RECORDING features. 
ON:Enable LOOP REC. 
OFF:Disable LOOP REC. 
‹Notes
z
After the power is turned off, this item
will default to OFF the next time the
power is turned on. 
zThis item cannot be changed when
“ON” or “ONE SHOT” is selected in
INTERVAL REC MODE.
–––F–
REC START ALL
NORMALSelect operating modes that allow 
recording to start. 
ALL:Allow recording to start during 
stop, recording pause, and 
playback. 
NORMAL:
  Allow recording to start during stop 
and recording pause. 
‹Note
Even if this is set to “ALL”, the operation 
is “NORMAL”, when “ON” or “ONE 
SHOT” is selected in INTERVAL REC 
MODE.
–CUF–
P.ON REC 
SLOT SELHOLD
SLOT1
Select the recording order of the slot 
when the power is turned on.
HOLD:
The recording order starts with the 
card previously selected when the 
power was turned off.
SLOT1:
The recording order starts with the 
card that is inserted in Slot 1 when the 
power is turned on.
–CUF–
Example of drop-frame
REC TIME02s00f
PA U S E  T I M E02s00f
TAKE TOTAL TIME40min
TOTAL REC TIME19m59s06f
AJ-HPX3000G(VQT1D27)E.book  161 ページ  ２００７年９月３日　月曜日　午後２時３４分 
						

							162Menu : Menu Description Tables
×Note
The  screen is displayed when
SYSTEM MODE is set to 1080-59.94i, 1080-50i (HD
mode).
The ____ in the Adjustable Range column indicates the
preset mode. 
OUTPUT SEL
Items/
Data Saved Adjustable 
Range
 Remarks 
OUTPUT ITEMMENU ONLY
TC
STATUS
Set the character contents 
superimposed onto the output signals 
for the VIDEO OUT connector (Analog 
or SDI) and MON OUT connector. 
MENU ONLY:
Displays only when the menu 
characters are superimposed. No 
display appears when other characters 
are superimposed.
TC:Display the time code. (Displays the 
menu when menu characters are 
superimposed.)
‹NoteThe TC display position moves up 
and down depending on the camera 
ID position. 
STATUS:
Display the same characters 
superimposed on the VF signal. 
(Displays the menu when menu 
characters are superimposed.)
–CUF–
MONITOR 
OUTVBSVF
YSelect the output signal on the MON OUT 
connector. 
VBS:Output a regular composite signal. 
VF:Output a VF Y signal. The status 
display is also superimposed. 
Y:Output a component Y signal.
‹Note
The VBS signal is output in playback 
mode.
–CUF –
MONITOR 
OUT CHARON
OFFSelect whether or not to superimpose 
characters on the MON OUT connector 
signal independently of the camera’s 
VIDEO OUT CHARACTER switch. (The 
character content is the same as the 
video output signal.)
ON:Enable superimpose. 
OFF:Disable superimpose. 
–CUF–
LCD MON 
CHARONOFF
Select whether or not to superimpose 
characters on the LCD monitor. (The 
character content is the same as the 
video output signal.)
ON:Enable superimpose. 
(Not interlocked with the VIDEO 
OUT CHARACTER switch.)
OFF:Disable superimpose. 
(Not interlocked with the VIDEO 
OUT CHARACTER switch.)
–CUF–
VF MODEMEMCAM
When the REC SIGNAL menu option on 
the SYSTEM MODE screen is set to 
CAM, select the image to display in the 
viewfinder. 
MEM:Display the playback image in the 
playback mode. 
CAM:Always display the camera image. 
–CUF–
THUMBNAIL 
OUTON
OFFSelect whether or not to output clip 
thumbnails displayed on the LCD 
monitor to the video output and monitor 
output signals. 
ON:Enable output. 
OFF:Disable output. 
‹Note
HD SDI signals are being output from 
the VIDEO OUT connector, thumbnails 
are not output.
–CUF–
DOWNCON SETTING
Items/
Data Saved Adjustable 
Range
 Remarks 
DOWNCON 
MODESQUEEZ
LT- B OX
S-CROP
For setting the mode of the down 
converter output signals.
–CUFR
DETAILONOFF
For setting the detail function for the 
down converter output signals ON/OFF.
The down converter output signals 
contain detailed components that are 
set during HD signal processing. In this 
setting, these signals overlap the 
detailed components dedicated to the 
down converter outputs.
Even if this setting is turned off, it is 
impossible to turn off the detailed 
components set during HD signal 
processing.
–CUFR
H.DTL LEVEL 00

08

31
For setting the horizontal detail 
correction level for the down converter 
output signals.
–CUFR
V.DTL LEVEL 00

04

31
For setting the vertical detail correction 
level for the down converter output 
signals.
–CUFR
DTL CORING 00
01
 : 
15
For setting the noise elimination level of 
the details.
–CUFR
H.DTL FREQ. 1

3

5
For selecting the horizontal detail 
frequencies.
1:2.5 MHz4:4 MHz
2:3 MHz5:4.5 MHz
3:3.5 MHz
–CUFR
2D LPF ON
OFFFor setting the 2-D low path filter 
reducing cross colors.
ON:Cross colors are reduced.
OFF:Cross colors are not reduced.
–CUFR
SETUP 0%
7.5%For setting the setup level for the down 
converter output signals.
¢Only for 1080-59.94i£
‹Note
When the system frequency is set to 50 
Hz, the setup level will be 0%.
–CUFR
AJ-HPX3000G(VQT1D27)E.book  162 ページ  ２００７年９月３日　月曜日　午後２時３４分 
						

							163Menu : Menu Description Tables
 Menu
The ____ in the Adjustable Range column indicates the
preset mode. 
LCD MONITOR
Items/
Data Saved Adjustable 
Range
 Remarks 
BRIGHTNESS –7 : +0 : +7
Adjust the LCD monitor brightness. 
–CUF –
COLOR 
LEVEL–7 : +0 : +7
Adjust the LCD monitor chroma level. 
–CUF –
CONTRAST –7 : +0 : +7
Adjust the LCD monitor contrast. 
–CUF –
BACKLIGHTNORMAL
HIGH
Adjust the backlightNORMALMode normally used
HIGH:This is brighter than NORMAL
–CUF –
SELF SHOOT NORMAL
MIRRORSelect whether or not to change the 
LCD monitor to mirror image. 
NORMAL:Do not change to mirror 
image. 
MIRROR:Change to mirror image. 
–CUF –
ASPECT 
CONV.SQUEEZE
LT. B OX
Select a screen ratio for images 
displayed on the LCD monitor (In SD 
mode only). 
SQUEEZE:Display images in the 
squeeze size. 
LT. B OX:Display images in the letter 
box size. 
‹Note
This item is enabled only when ASPECT 
described in “SYSTEM MODE” is set 
to16:9.
–CUF –
GENLOCK
Items/
Data Saved Adjustable 
Range
 Remarks 
GENLOCKINTEXT
Switch the camera synchronising signal. 
INT:Synchronise with the internal 
reference signal regardless of the 
reference signal input to the 
GENLOCK IN connector. 
EXT:Synchronise with the reference 
signal input to the GENLOCK IN 
connector. 
–CUFR
GL PHASEHD SDI
COMPOSIT
For selecting the output signals that lock 
phases to the signals that are input in 
the GENLOCK IN connector. (Only for 
1080-59.94i, 1080-50i
£HD SDI:
For locking the HD SDI signals to the 
GENLOCK input.
For the down converter output 
signals, the start position of the video 
delays by about 90 lines.
COMPOSIT:
For locking the down converter output 
signals to the GENLOCK input.
For the HD SDI output signals, the 
start position of the video gains by 
about 90 lines.
–CUFR
H PHASE 
COARSE–100 : +000 : +100
Perform coarse phase adjustment for 
horizontal hold when configuring a 
system. 
–––––
Items/
Data Saved Adjustable 
Range
 Remarks 
H PHASE 
FINE–100 : +000 : +100
Perform fine phase adjustment for 
horizontal hold when configuring a 
system. 
–––––
1394 SETTING
Items/
Data Saved Adjustable 
RangeRemarks 
1394 SPEED S100
S200
S400For setting the transfer rate of signals 
output from the DVCPRO connector.
S100:100Mbps
S200:200Mbps
S400:400Mbps
–CUF –
1394 IN CH 0
 : 
63
AU TOFor setting the input channel of signals 
input to the DVCPRO connector.
0 - 63:To fix to the designated value
AUTO :To follow the settings of the 
externally connected devices
–CUF –
1394 OUT CH 0
 : 
63
AU TOFor setting the input channel of signals 
output from the DVCPRO connector.
0 - 63:To fix to the designated value
AUTO :To follow the settings of the 
externally connected devices
–CUF –
1394 
CONTROLOFFBOTH
For setting the control for recording 
start/stop operations of external devices 
that are connected to the DVCPRO 
connector.
OFF:Do not control the externally 
connected devices.
BOTH:To control both the unit and the 
externally connected devices
–CUF –
1394 CMD SEL REC_P
STOP
For setting the control of recording stop 
operations of the external devices that 
are connected to the DVCPRO 
connector.
REC_P:Operation to pause recording
STOP:Stopping operation
–CUF –
AJ-HPX3000G(VQT1D27)E.book  163 ページ  ２００７年９月３日　月曜日　午後２時３４分 
						

							164Menu : Menu Description TablesThe ____ in the Adjustable Range column indicates the
preset mode. 
PA I N T
RB GAIN CONTROL
Items/
Data Saved Adjustable 
Range
 Remarks 
R GAIN AWB 
PRE–200

+000

+200
For setting the Rch gain when the 
WHITE BAL switch is in the PRST 
position.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
B GAIN AWB 
PRE–200

+000

+200
For setting the Bch gain when the 
WHITE BAL switch is in the PRST 
position.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
R GAIN AWB A –200

+000

+200
For setting the Rch gain when the 
WHITE BAL switch is in the A position.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
B GAIN AWB A –200

+000

+200
For setting the Bch gain when the 
WHITE BAL switch is in the A position.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
R GAIN AWB B –200

+000

+200
For setting the Rch gain when the 
WHITE BAL switch is in the B position.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
B GAIN AWB B –200

+000

+200
For setting the Bch gain when the 
WHITE BAL switch is in the B position.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
AWB  A GA IN  
OFFSETON
OFFFor setting the values of the Rch gain 
and the Bch gain when the auto white 
balance is executed as the WHITE BAL 
switch is in the A position.
ON:To retain the values set in the 
items of R GAIN AWB A and B 
GAIN AWB A
OFF:The values of the Rch gain and 
the Bch gain is set to “0”.
SCUFR
AWB  B GA IN  
OFFSETON
OFFFor setting the values of the Rch gain 
and the Bch gain when the auto white 
balance is executed as the WHITE BAL 
switch is in the B position.
ON:To retain the values set in the 
items of R GAIN AWB B and B 
GAIN AWB B
OFF:The values of the Rch gain and 
the Bch gain is set to “0”.
SCUFR
RGB BLACK CONTROL
Items/
Data Saved Adjustable 
Range
 Remarks 
MASTER PED –200

+015

+200
For setting the level of the master 
pedestal.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
R PEDESTAL
–100

+000

+100
For setting the pedestal level of the Rch.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
G PEDESTAL –100

+000

+100
For setting the pedestal level of the 
Gch.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
B PEDESTAL –100

+000

+100
For setting the pedestal level of the Bch.zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
PEDESTAL 
OFFSETON
OFFFor setting the pedestal levels of the 
Rch, the Gch and the Bch when the 
auto black balance is adjusted.
ON:To retain the values set in the 
respective items of R PEDESTAL, 
G PEDESTAL, and B PEDESTAL
OFF:The pedestal levels of the Rch, 
the Gch and the Bch are set to 
”0”.
SCUF –
R FLARE –100

+000

+100
For adjusting the flare level of the Rch. 
Adjustment values in this item are 
added to the flare adjustment value that 
is adjusted on  
screen.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
G FLARE –100

+000

+100
For adjusting the flare level of the Gch. 
Adjustment values in this item are 
added to the flare adjustment value that 
is adjusted on  
screen.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
B FLARE –100

+000

+100
For adjusting the flare level of the Bch. 
Adjustment values in this item are 
added to the flare adjustment value that 
is adjusted on  
screen.
zIf the remote control unit is
connected, settings made from the
menu are disabled. (The set value is
displayed.)
SCUFR
AJ-HPX3000G(VQT1D27)E.book  164 ページ  ２００７年９月３日　月曜日　午後２時３４分 
						

							165Menu : Menu Description Tables
 Menu
‹Note
The items indicated by „ are the setting items for PAINT
MENU SW(
„) R/W in the 
screen. The items without 
„ are the setting items for
PAINT MENU LEVEL R/W. 
Please refer to [
SD CARD R/W SELECT] (page 187) for
more information. 
All of the preset data for the respective linear matrix data of
the 
„ MATRIX TABLE B are set to +00.
The ____ in the Adjustable Range column indicates the
preset mode. 
MATRIX
Items/
Data Saved Adjustable 
Range
 Remarks 
„MATRIX 
TABLEA
B
For selecting the color correction table 
for the linear matrix.
SCUFR
MATRIX R-G –63

+31

+63
For performing the linear matrix 
adjustment. (red/green)
SCUFR
MATRIX R-B –63

–04

+63
For performing the linear matrix 
adjustment. (red/blue)
SCUFR
MATRIX G-R –63

–01

+63
For performing the linear matrix 
adjustment. (green/red)
SCUFR
MATRIX G-B –63

+04

+63
For performing the linear matrix 
adjustment. (green/blue)
SCUFR
MATRIX B-R –63

+01

+63
For performing the linear matrix 
adjustment. (blue/red)
SCUFR
MATRIX B-G –63

–01

+63
For performing the linear matrix 
adjustment. (blue/green)
SCUFR
„L MATRIX 
TABLEOFF
A
B
For selecting the color correction table 
when the GAIN switch is in the L 
position.
SCUFR
„M MATRIX 
TABLEOFF
A
B
For selecting the color correction table 
when the GAIN switch is in the M 
position.
SCUF –
„H MATRIX 
TABLEOFF
A
B
For selecting the color correction table 
when the GAIN switch is in the H 
position.
SCUF –
COLOR CORRECTION
Items/
Data Saved Adjustable 
Range
 Remarks 
R
(SAT)–63 : +00 : +63
For performing the color saturation 
correction of red. 
SCUFR
R-Mg
(SAT)–63 : +00 : +63
For performing the color 
saturationcorrection between red and 
magenta.
SCUFR
Mg
(SAT)–63 : +00 : +63
For performing the color 
saturationcorrection of magenta.
SCUFR
Mg-B
(SAT)–63 : +00 : +63
For performing the color saturation 
correction between magenta and blue.
SCUFR
B
(SAT)–63 : +00 : +63
For performing the color saturation 
correction of blue.
SCUFR
B-Cy
(SAT)–63 : +00 : +63
For performing the color saturation 
correction between blue and cyan.
SCUFR
Cy
(SAT)–63 : +00 : +63
For performing the color saturation 
correction of cyan.
SCUFR
Cy-G
(SAT)–63 : +00 : +63
For performing the color saturation 
correction between cyan and green.
SCUFR
G
(SAT)–63 : +00 : +63
For performing the color saturation 
correction of green.
SCUFR
G-Yl
(SAT)–63 : +00 : +63
For performing the color saturation 
correction between green and yellow.
SCUFR
Yl
(SAT)–63 : +00 : +63
For performing the color saturation 
correction of yellow.
SCUFR
Yl-R
(SAT)–63 : +00 : +63
For performing the color saturation 
correction between yellow and red.
SCUFR
AJ-HPX3000G(VQT1D27)E.book  165 ページ  ２００７年９月３日　月曜日　午後２時３４分 
						

							166Menu : Menu Description Tables The ____ in the Adjustable Range column indicates the
preset mode. 
‹Notes
zThe items indicated by „ are the setting items for PAINT
MENU SW(
„) R/W in the 
screen. The items without 
„ are the setting items for
PAINT MENU LEVEL R/W. Please refer to [SD CARD R/
W SELECT] (page 187) for more information. 
zIf images are shot when the master gain is set to –3dB,
some coloring phenomena may occur on images in very
bright sections. The color phenomena become more
significant as the difference in the color temperature of the
subject incident to the unit from 3200K becomes larger.In
order to suppress the coloring phenomena, switch the
OUTPUT AUTO KNEE switch to “CAM AUTO KNEE OFF”,
set the MANUAL item on the KNEE/LEVEL screen to “ON”,
and then set a smaller value for the KNEE SLOPE item and
WHITE CLIP LVL item on the KNEE/LEVEL screen. After
executing these settings, confirm that there are no coloring
phenomena and then start shooting.
Items/
Data Saved Adjustable 
Range
 Remarks 
R(PHASE) –63 : +00 : +63
For performing the hue correction for 
red.
SCUFR
R-Mg(PHASE) –63 : +00 : +63
For performing the hue correction 
between red and magenta.
SCUFR
Mg(PHASE) –63 : +00 : +63
For performing the hue correction for 
magenta.
SCUFR
Mg-B(PHASE) –63 : +00 : +63
For performing the hue correction 
between magenta and blue.
SCUFR
B(PHASE)
–63 : +00 : +63
For performing the hue correction for 
blue.
SCUFR
B-Cy(PHASE) –63 : +00 : +63
For performing the hue correction 
between blue and cyan.
SCUFR
Cy(PHASE) –63 : +00 : +63
For performing the hue correction for 
cyan.
SCUFR
Cy-G(PHASE) –63 : +00 : +63
For performing the hue correction 
between cyan and green.
SCUFR
G(PHASE) –63 : +00 : +63
For performing the hue correction for 
green.
SCUFR
G-Yl(PHASE) –63 : +00 : +63
For performing the hue correction 
between green and yellow.
SCUFR
Yl(PHASE) –63 : +00 : +63
For performing the hue correction for 
yellow.
SCUFR
Yl-R(PHASE) –63 : +00 : +63
For performing the hue correction 
between yellow and red.
SCUFR
„COLOR 
CORRECTON
OFFFor switching ON/OFF of the 12-axis 
independent color correction of the 
position selected with the GAIN switch 
(L, M, H).
SCUFR
LOW SETTING
Items/
Data Saved Adjustable 
Range
 Remarks 
„MASTER 
GAIN–3dB : 0dB : 30dB
Select the master gain from –3, 0, 3, 6, 
9, 12, 15, 18, 21, 24, 27, or 30dB. 
SCUFR
H.DTL LEVEL 00 : 10 : 63
For performing the horizontal detail 
correction level setting.
SCUFR
V.DTL LEVEL 00 : 15 : 31
For performing the vertical detail 
correction level setting.
SCUFR
DTL CORING 00 : 01 : 15
For performing the noise elimination 
level setting for detail.
SCUFR
H.DTL FREQ.
00 : 18 : 31
For performing the horizontal detail 
frequency selection.
SCUFR
LEVEL 
DEPEND.0
1
 : 5
For setting the LEVEL DEPEND.
When the Y-detail is emphasized, details 
of dark sections are compressed.
If the numerical value is larger, details of 
bright sections are also compressed.
SCUFR
MASTER 
GAMMA0.30 : 0.45 : 0.75
For setting the master gamma. (0.01 
step)
SCUFR
BLACK 
GAMMA–3 : OFF : +3
For setting the gamma curve for the dark 
portion.
–3 to –1:
The dark portion is compressed.
OFF:
Standard state
+1 to +3:
The dark portion is extended.
SCUFR
„MATRIX 
TA B L EOFF
A
B
For selecting the color correction table 
for the linear matrix.
SCUFR
„COLOR 
CORRECTON
OFFFor switching ON/OFF of the 12-axis 
independent color correction.
SCUFR
AJ-HPX3000G(VQT1D27)E.book  166 ページ  ２００７年９月３日　月曜日　午後２時３４分 
						

							167Menu : Menu Description Tables
 Menu
‹Note
The items indicated by „ are the setting items for PAINT
MENU SW(
„) R/W in the 
screen. The items without 
„ are the setting items for
PAINT MENU LEVEL R/W. 
Please refer to [SD CARD R/W SELECT] (page 187) for
more information. 
The ____ in the Adjustable Range column indicates the
preset mode. 
MID SETTING
Items/
Data Saved Adjustable 
Range
 Remarks 
„MASTER 
GAIN–3dB

6dB

30dB
Select the master gain from –3, 0, 3, 6, 
9, 12, 15, 18, 21, 24, 27, or 30dB. 
SCUF –
H.DTL LEVEL 00

08

63
For performing the horizontal detail 
correction level setting.
SCUF –
V. D T L  L E V E L 0 0

12

31
For performing the vertical detail 
correction level setting.
SCUF –
DTL CORING 00

02

15
For performing the noise elimination 
level setting for detail.
SCUF –
H.DTL FREQ.
00

18

31
For performing the horizontal detail 
frequency selection.
SCUF –
LEVEL 
DEPEND.0
1


5
For setting the LEVEL DEPEND.
When the Y-detail is emphasized, 
details of dark sections are 
compressed.
If the numerical value is larger, details of 
bright sections are also compressed.
SCUF –
MASTER 
GAMMA0.30

0.45

0.75
For setting the master gamma. (0.01 
step)
SCUF –
BLACK 
GAMMA–3 : OFF : +3
For setting the gamma curve for the 
dark portion.
–3 to –1:
The dark portion is compressed.
OFF:
Standard state
+1 to +3:
The dark portion is extended.
SCUF –
„MATRIX 
TABLEOFF
A
B
For selecting the color correction table 
for the linear matrix.
SCUF –
„COLOR 
CORRECTON
OFFFor switching ON/OFF of the 12-axis 
independent color correction.
SCUF –
HIGH SETTING
Items/
Data Saved Adjustable 
Range
 Remarks 
„MASTER 
GAIN–3dB

12dB

30dB
Select the master gain from –3, 0, 3, 6, 
9, 12, 15, 18, 21, 24, 27, or 30dB. 
SCUF –
H.DTL LEVEL 00

06

63
For performing the horizontal detail 
correction level setting.
SCUF –
V.DTL LEVEL 00

10

31
For performing the vertical detail 
correction level setting.
SCUF –
DTL CORING 00

03

15
For performing the noise elimination 
level setting for detail.
SCUF –
H.DTL FREQ.
00

18

31
For performing the horizontal detail 
frequency selection.
SCUF –
LEVEL 
DEPEND.0

3

5
For setting the LEVEL DEPEND.
When the Y-detail is emphasized, 
details of dark sections are 
compressed.
If the numerical value is larger, details of 
bright sections are also compressed.
SCUF –
MASTER 
GAMMA0.30

0.55

0.75
For setting the master gamma. (0.01 
step)
SCUF –
BLACK 
GAMMA–3 : OFF : +3
For setting the gamma curve for the 
dark portion.
–3 to –1:
The dark portion is compressed.
OFF:
Standard state
+1 to +3:
The dark portion is extended.
SCUF –
„MATRIX 
TA B L EOFF
A
B
For selecting the color correction table 
for the linear matrix.
SCUF –
„COLOR 
CORRECTON
OFFFor switching ON/OFF of the 12-axis 
independent color correction.
SCUF –
AJ-HPX3000G(VQT1D27)E.book  167 ページ  ２００７年９月３日　月曜日　午後２時３４分 
						

							168Menu : Menu Description Tables The ____ in the Adjustable Range column indicates the
preset mode. 
ADDITIONAL DTL
Items/
Data Saved Adjustable 
Range
 Remarks 
KNEE APE 
LV LOFF
1 : 5
For changing the detail level of the high 
brightness portion.
SCUFR
DTL GAIN(+) –31 : +00 : +31
Adjust the detail level toward + 
(upwards). 
SCUFR
DTL GAIN(–) –31 : +00 : +31
Adjust the detail level toward the – 
(downwards). 
SCUFR
DTL CLIP00 : 63
For setting the level for clipping the 
detail signals.
SCUFR
DTL SOURCE(R+G)/2(G+B)/2
2G+R+B /4
(3G+R)/4
R
G
For setting the proportion of the RGB 
signal components that provide the 
detail.
SCUFR
MASTER DTL –31 : +00 : +31
For revising the master detail level.
SCUFR
AJ-HPX3000G(VQT1D27)E.book  168 ページ  ２００７年９月３日　月曜日　午後２時３４分 
						

							169Menu : Menu Description Tables
 Menu
‹Note
The items indicated by „ are the setting items for PAINT
MENU SW(
„) R/W in the 
screen. The items without 
„ are the setting items for
PAINT MENU LEVEL R/W. 
Please refer to [SD CARD R/W SELECT] (page 187) for
more information. 
The ____ in the Adjustable Range column indicates the
preset mode. 
SKIN TONE DTL
Items/
Data Saved Adjustable 
Range
 Remarks 
„SKIN TONE 
DTLOFF
A
B
ABFor selecting the skin color table for 
enabling the skin tone detail.
The skin color table is provided in the 
SKIN TONE TABLE item.
By enabling the skin tone detail, it is 
possible to shoot human skin more 
accurately.
SCUFR
„SKIN TONE 
ZEBRA VFON
OFFFor the setting to display the zebra 
pattern in the skin tone area displayed in 
the viewfinder screen.
The zebra pattern is displayed when this 
item is turned “ON” and the  screen is opened.
The zebra pattern is displayed on area A 
or B, which is selected in the SKIN 
TONE TABLE item.
It is impossible to display both area A 
and B at the same time.
SCUFR
SKIN TONE 
TABLEA
B
For selecting the skin color table for 
subjects to which the skin tone table 
applies.
SCUFR
SKIN TONE 
GETFor fetching the color information of A or 
B, which is selected in the SKIN TONE 
TABLE item, near the center marker.
When this function is executed, data 
from I CENTER to Q PHASE are fetched 
automatically.
The fetched data will be the table data of 
A or B, which is selected in the SKIN 
TONE TABLE item.
It is impossible to obtain color 
information of both A and B at the same 
time.
–––––
SKIN DTL 
CORING0 : 5 : 7
For setting the effect level of the skin 
tone detail.
SCUFR
Y MAX 000 : 190 : 255
For setting the maximum value of 
brightness for enabling the skin tone.
SCUFR
Y MIN
000 : 010 : 255
For setting the minimum value of 
brightness for enabling the skin tone.
SCUFR
I CENTER 000 : 035 : 255
For setting the center position on the I 
axis (for setting an area that enables 
skin tone.)
SCUFR
I WIDTH 000 : 055 : 255
For setting the area width for enabling 
the skin tone on the I-axis of which the 
center is the I CENTER.
SCUFR
Q WIDTH 00 : 10 : 90
For setting the area width for enabling 
the skin tone on the Q-axis of which the 
center is the I CENTER.
SCUFR
Q PHASE –180 : +000 : +179
For setting phases of the area for 
enabling skin tone as setting the 
standard to the Q-axis.
SCUFR
R-Y
B-Y
Q-WIDTHI-WIDTH
Q-PHASE I-CENTER
Y
Y- M A X
Y- M I N
0
– direction+ direction
 = SKIN TONE AREA
AJ-HPX3000G(VQT1D27)E.book  169 ページ  ２００７年９月３日　月曜日　午後２時３４分 
						

							170Menu : Menu Description Tables
‹Note
The items indicated by „ are the setting items for PAINT
MENU SW(
„) R/W in the 
screen. The items without 
„ are the setting items for
PAINT MENU LEVEL R/W. 
Please refer to [SD CARD R/W SELECT] (page 187) for
more information. The ____ in the Adjustable Range column indicates the
preset mode. 
KNEE/LEVEL
Items/
Data Saved Adjustable 
Range
 Remarks 
MASTER PED –200 : +015 : +200
Set the master pedestal. 
SCUFR
„MANUAL 
KNEEONOFF
Set the mode when the AUTO KNEE 
switch is OFF. The KNEE POINT/
SLOPE set value is enabled when this 
setting is ON. 
SCUFR
KNEE POINT 70.0% : 93.0% : 107.0%
For setting the knee point position in 
increments of 1% steps.
SCUFR
KNEE SLOPE 00 : 85 : 99
For setting the inclination of the knee.
SCUFR
„WHITE CLIPONOFF
Set the WHITE CLIP feature to ON or 
OFF. The WHITE CLIP LVL set value is 
enabled when this setting is ON. 
SCUFR
WHITE CLIP 
LV L90% : 109%
Set WHITE CLIP LEVEL. 
SCUFR
A.KNEE 
POINT80% : 93% : 107%
Set the AUTO KNEE POINT position in 
1% steps. This setting is enabled when 
the OUTPUT/AUTO KNEE selector 
switch is set to CAM.AUTO KNEE ON. 
SCUFR
A.KNEE LVL 100 : 107 : 109
Set the AUTO KNEE LEVEL. 
SCUFR
A.KNEE 
RESPONSE1 : 4 : 8
Set the AUTO KNEE response speed. 
The smaller the setting value, the faster 
the response speed.
SCUFR
CHROMA 
LEVELOFF
–99%
 : +00% : +40%
For setting the chroma level of the PR 
signals and the PB signals.
If this is set to OFF, the color elements of 
video signals are eliminated.
SCUFR
DRS EFFECT 
DEPTH1
2
3
Set the compression level of the high-
brightness component of DRS. If the 
numerical value is larger, the 
compression level of the high-brightness 
component increases.
SCUFR
GAMMA
Items/
Data Saved Adjustable 
Range
 Remarks 
MASTER 
GAMMA0.30 : 0.45 : 0.75
Set the master gamma in 0.01% steps. 
SCUFR
R GAMMA –15 : +00 : +15
Set the Rch gamma. 
SCUFR
B GAMMA –15 : +00 : +15
Set the Bch gamma. 
SCUFR
AJ-HPX3000G(VQT1D27)E.book  170 ページ  ２００７年９月３日　月曜日　午後２時３４分