Panasonic LCD Projector Pt Vw440 Operating Instructions

							ENGLISH - 61
Settings
Network
Select [Setting] from the Main Menu (see 
“Navigating through the menu” on page 36), 
then select the item from the sub-menu.
Remote ControlControl Panel
Projector name
You can change the projector name to be displayed 
on the network.
Press ▲▼ to select [Projector name], 1 ) 
and press  button.
Select characters with the ▲▼◄► 2 ) 
buttons and press the  
button to enter the projector name.
       Select [BS] to delete one character selected 
with the cursor in the input box and press the 
 button.
Select [Set] with the ▲▼◄► buttons 3 ) 
and press the  button.                                          
Select [Cancel] to undo the changes and then 
press the  button.
Select [YES] or [No] with the ▲▼ 4 ) 
buttons and press the  
button.
Note
[Name  zØØØØ] (ØØØØ
is four-digit number) is set 
before the projector leaves the factory.
Network setup
You can make detailed wired LAN settings.
Press ▲▼ to select [Network setup], 1 ) 
and press  button.
Press ▲▼ to select an item, and 2 ) 
change the setting according to the 
instructions.
DHCP (DHCP client 
function)
On:If a DHCP server 
exists in the 
network to which 
the projector is 
connected, the 
IP address will 
automatically be 
acquired.
Off:If a DHCP 
server does 
not exist in the 
network to which 
the projector 
is connected, 
additionally set 
[IP address], 
[Subnet mask 
] and [ Default 
gateway ].
IP address (Display of IP 
address and setting)
Enter the IP address 
if DHCP server is not 
used.
Subnet mask(Displaying and 
setting the subnet 
mask)
If not using a DHCP 
server, enter the subnet 
mask.
Default gateway  (Display of gateway 
address and setting)
Enter the gateway 
address if DHCP server 
is not used.
DNS1(Display of Preferred DNS server address and setting)
Enter the DNS server address if DHCP server is not used.
DNS2(Display of Alternate DNS server address and setting)
Enter the alternate DNS server address if DHCP server is not used.
Press ▲▼◄► to select [Set], and press 3 ) 
 button.
Default wired LAN settings  z 
The following settings are set before the 
projector leaves the factory.
DHCPOff
IP address1 9 2 .1 6 8 .1 0 .1 0 0
Subnet mask255.255.255.0
Default gateway1 9 2 .1 6 8 .1 0 .1
DNS1/DNS2NONE
Note
Before using the DHCP server, make sure the DHCP  z
server is already functioning.
For details of IP address, subnet mask, gateway and  z
DNS, ask the network administrator. 
						

							Network
62 - ENGLISH
Settings
Network control
Set when you want to control the projector from a 
computer connected to the network.
Press ▲▼ to select [Network control].1 ) 
Press  button to select [On] 2 ) 
or [Off] with the ▲▼ buttons.
Network status
This function shows the LAN setting environment of 
the currently selected projector.
Press ▲▼ to select [Network status].1 ) 
Press  button or the ► button 2 ) 
to show the information of the current 
projector status.
AMX D.D.
This function allows the projector to be detected by 
AMX Device Discovery. For more details, visit the 
following website. 
http://www.amx.com/
Press ▲▼ to select [AMX D.D.].1 ) 
Press 2 )  button to select [On] 
or [Off] with the ▲▼ buttons.
RoomView
This function allows the projector to monitor and 
control the projector through network with Crestron 
RoomView.
Press ▲▼ to select 1 ) [RoomView].
Press 2 )  button to select [On] 
or [Off] with the ▲▼ buttons.
This projector supports the following application 
software from Crestron company.
 • RoomView Express
 • Fusion RV
 • RoomView Server Edition
"Crestron RoomView" is a system developed by
Crestron Electronics, Inc. which collectively manage
and control multiple system devices connected via
the network, from a computer. This projector supports
"Crestron RoomView".

For details of "Crestron RoomView", refer to the Crestron 
Electronics, Inc. website (Provided only in English). 
http://www.crestron.com/ 
For the download of "RoomView Express", refer to the Cre-
stron Electronics, Inc. website (Provided only in English). 
http://www.crestron.com/getroomview
Network factory default
You can reset the network setting to the factory 
default of the projector.
Press ▲▼ to select [Network factory 1 ) 
default], and press  button. 
A confirmation box appears and select 2 ) 
[Yes] and then press  button.
Another confirmation box appears and 3 ) 
select [Yes] and then press  
button. 
						

							Network
ENGLISH - 63
Settings
Network connections
The projector has a network fuction, and the following operations are av\
ailable from the computer using the web 
browser control.
Setting and adjustment of the projector. z
Display of the projector status. z
Transmission of an E-mail message when there is a problem with the projec\
tor. z
Note
A LAN cable is required to use the network function. z
ComputerProjector
LAN cable (straight) LAN cable (straight)
Hub
 Notes on LAN network connections
A Web browser is required to use this function . Confirm that the Web browser can be used beforehand.  z
Compatible OS : Windows XP/Windows Vista/Windows 7, Mac OS X v10.4/v10.5/v10.6/v10.7  
Compatible Web Browser : Internet Explorer 7.0/8.0/9.0, Safari 4.0/5.0 (Mac OS)
Communication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be  z
used beforehand.
Use shielded LAN cable (STP cable) that is compatible with category 5 or above. z
Use a LAN cable with length of 100m or shorter. z 
						

							Network
64 - ENGLISH
Settings
Computer operation
Connection can be made with wired LAN. However, confirm to your system administrator on network settings 
before changing any settings.
Turn on the computer.1 ) 
Make the network setting according to your system administrator.2 ) 
If the projector settings are the default settings (See page 61), the computer can be used with the 
following network settings.
DHCPOff
IP address1 9 2 .1 6 8 .1 0 .1 0 1
Subnet mask255.255.255.0
Default gateway1 9 2 .1 6 8 .1 0 .1
DNS1/DNS2NONE
Accessing from the Web browser
Activate the Web browser in the personal computer.1 ) 
Enter the IP address set by the projector into the URL input field of the Web browser.2 ) 
Enter your3 )  “User name” and “Password”.
The factory default settings are user1 (user privileges)   z
or admin1 (administrator privileges) for the use name  
and panasonic (lowercase letters) for the password.
Click [OK] to display the Projector  4 ) 
status page.
   z“Projector status” page is displayed.
Note
Avoid activating two or more Web browser simultaneously to work out setting or control actions. z
Change the password first of all. z
Administrator privileges enable the use of all functions. User privileges enable the use of only “Projector status”,  z
“Network status”, “Basic control”, “Advanced control” and “Change password”.
If you want to control the projector using a Web browser, set [Network control] in the network menu to [On]. z
There are some control items used with the JavaScript function in the setting pages. If the web browser is set  z
not to use this JavaScript function, it may not control the projector properly.  
						

							Network
ENGLISH - 65
Settings
Description of each item  J
1 Page selection tabs
  Click these to switch pages.
2 Monitor information button 
Click this item, and the status of the projector is 
displayed.
3 Projector control button 
Click this item to display the projector control 
page.
4 Detailed set up button 
Click this item to display the advanced settings 
page.
5 Change password button
    Click this button to display the password change 
page.
6  Crestron RoomView button
    Click this button to monitor and control the 
projector through the network.
7  Language switch button
    Click this button to switch language between 
English and Japanese.
5
4
3
2
1
6
7
Projector status page J
Click [Status], then [Projector status] to display the Status information page.
This page displays the projector statuses established for the items shown below.
1  Displays the type of projector.
2 Displays the firmware version of the projector 
main unit.
3 Displays the power source status.
4 Displays the video mode status.
5 Displays the serial number of the projector.
6 Displays the firmware version of the network.
7 Displays the AV mute status.
8 Displays the volume status.
9 Displays the status of input switch.
10  Displays the intake temperature status of the  
     projector.
11 Displays the exhaust temperature status of the 
projector. 
12   Displays the optics module temperature status of 
the projector.
13 Displays the use time of the lamp.
14   Displays the self diagnostics information. 
     (Æ page 66)
15 Displays the runtime of the projector.
1
2
3
4
5
6
7
89101112
14
13
15 
						

							Network
66 - ENGLISH
Settings
Error information page  J
If [Error (Detail)] is displayed in the self-diagnosis information display column on the [Projector status] screen, 
click the part to display the details of the error.
Depending on the nature of the error, the projector may be placed in the standby mode for its own protection.• 
When [FAILED] has appeared for an item
ParameterDescription
FA NTrouble has occurred in the fan or its drive circuit. Consult your dealer.
INTAKE AIR TEMPER ATURE
Intake air temperature is high. It could be because it is used in an environment of high 
temperature such as close to a heating device, etc., the air intake is blocked, or the air 
filter is clogged.
EXHAUST AIR TEMPER ATUREExhaust air temperature is high. Exhaust may be blocked, or [Fan control] mode may 
be set wrong. (Æpage 57)
OPTICS MODULE TEMPER ATUREOptics module temperature is high.
LAMP REMAIN TIMEThe lamp runtime has exceeded the prescribed cumulative time, and it is now time to 
replace the lamp.
LAMP STATUSThe lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power.
APERTURE (CONTR AST-SHUTTER)Trouble has occurred in the contrast shutter circuitry. Consult your dealer.
OK:      Normal operation
FAILED:      Occurrence of trouble
WARNING: Abnormal condition
Network status page J
Displays the current configuration information of the network.
Displays the configuration details of wired LAN.
 
						

							Network
ENGLISH - 67
Settings
Basic control page  J
To move from another page, click [Projector control], then [Basic control].
1 Power standby/on control
2 Use these to select the input signals
3 Volume adjust
4 Switches image mode
5 Operation of AV mute
5
4
3
2
1
Detail control page J
Click [Projector control], then [Advanced control] to display the Detail control page.
1  Execute Auto setup function
2 Operations on Screen mode
3  Operations on Keystone function
4  Operations on Rear/Ceiling
5  Operations on Image adjust
1
2
3
4
5 
						

							Network
68 - ENGLISH
Settings
Network config page J
You can change network settings on projector when connecting with the administrator authority.
LAN settings z 
Click [Detailed set up] in the menu.1 ) 
Click [Change] to change the LAN settings.2 ) 
 
To return to the previous window, click [Back]. z
Complete the detailed settings and  3 ) 
click [Next].
 
When [Next] is clicked, the next page appears, enabling   z
you to complete the detailed settings as desired.  
Settings performed here are the same as the  
settings performed with the [Network] menu of  
the projector.
Click [Submit].4 ) 
  zThe settings will be registered.
Note
Changing the setting of LAN while connected with LAN  z
    might disconnect the connection. 
						

							Network
ENGLISH - 69
Settings
Ping test page  J
This page makes it possible to check whether the network is connected to the e-mail server, POP server, DNS 
server, etc.
Click [Detailed set up], then [Ping test] to display the Ping test page.
Display which appears when the connection
was successful.
Display which appears when the connection
failed.
1 Enter the IP address of the server to be tested.
2 Button for conducting the test.
21 
						

							Network
70 - ENGLISH
Settings
E-mail set up page  J
With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can be 
sent to one or more preset e-mail addresses (maximum two addresses).
Click [Detailed set up], then [E-mail set up] to display the E-mail setup page.
1 Select Enable to use the e-mail function.
2 Enter the IP address or server name of the e-mail 
server (SMTP). The DNS server must be set if the 
server name is entered.
3 Enter the e-mail address of the projector. 
(maximum 63 characters)
4 The user can enter the location of, for example, 
the installed projector so that the recipient may 
easily identify the originator of the e-mail. 
(maximum 63 characters)
5 The user can modify the minimum time interval 
of temperature warning mail. The default value 
is 60 minutes. In this case, the user cannot send 
another mail for 60 minutes after sending previous 
temperature warning mail even the set warning 
temperature is reached again.
6 Select the temperature of the intake sensor at 
which to send a warning message.
7 Enter the E-mail Address1 of your desired recipient.
8 Select the conditions for sending e-mail.
     MAIL CONTENTS:Select [NORMAL] or [SIMPLE].
ERROR:An error is detected by self-diagnosis.
LAMP RUNTIME:Remaining lamp service time has reached the value set in the field.
INTAKE AIR TEMPERATURE:Intake air temperature has reached the value set in the field.
6
5
4
3
2
1
8
7