Home > Panasonic > Projector > Panasonic LCD Projector Pt Vw440 Operating Instructions

Panasonic LCD Projector Pt Vw440 Operating Instructions

    Download as PDF Print this page Share this page

    Have a look at the manual Panasonic LCD Projector Pt Vw440 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							ENGLISH - 51
    Settings
    Sound
    Select [Sound] from the Main Menu (see 
    “Navigating through the menu” on page 36), 
    then select the item from the sub-menu.
    Remote ControlControl Panel
    Volume
    Press ▲▼ to select [Volume] and then 1 ) 
    press the  button.
    Press ◄► to adjust the volume.2 ) 
    Press  button to set the volume. z
    OperationAdjustmentAdjustment 
    range
    Press ►.turn up the 
    volume
    Maximum 
    value 63
    Press ◄.turn down the 
    volume
    Minimum 
    value 0
    You can also press  buttons on  z
    the remote control or control panel to adjust the 
    volume.
    Mute
    Press ▲▼ to select [Mute].1 ) 
    Press the  button to switch 2 ) 
    the mute function [On]/[Off].
    Press the  button on the remote  z
    control also can switch the mute function On/
    Off. (Æpage 35) 
    MIC 
    Press ▲▼ to select [MIC] and then 1 ) 
    press the  button.
    Press ▲▼ to switch the MIC function 2 ) 
    [On]/[Off].
    Note
    When [Off] is selected in [MIC] function, the [MIC  z
    gain] and [Standby MIC out] functions are not 
    available.
    Connect  the computer 2 audio input signals to   z
    COMPUTER AUDIO IN 1 terminal as the MIC 
    function is turned on.
    If the [MIC] function is turned on when  z
    connecting PC audio to the AUDIO IN (a mini 
    jack), loud sound may be output suddenly 
    depending on the setting value of [MIC gain].
    MIC gain
    Press ▲▼ to select [MIC gain] and 1 ) 
    then Press the  button.
    Press ◄► to adjust the MIC mixing 2 ) 
    gain.
    Press  button to set the [MIC gain]. z
    OperationAdjustmentAdjustment 
    range
    Press ►.turn up the MIC 
    mixing gain
    Maximum 
    value 63
    Press ◄.turn down the  
    MIC mixing gain
    Minimum 
    value 0
    Standby MIC out
    Press ▲▼ to select [Standby MIC out]1 ) 
    and then press the  button.
    Press ▲▼ to switch the [Standy MIC 2 ) 
    out] function [On]/[Off].
    Note
    When setting the [Standby MIC out] function  z
    to [On] and in Standby mode status, only 
    [MIC] input volume can be output. Press the 
     buttons on the control panel or 
    on the remote control to adjust the MIC input 
    volume. 
    Only the Standby mode is set to [Network],  z
    [Standby MIC out] can be selected. 
    						
    							52 - ENGLISH
    Settings
    Setting
    Select [Setting] from the Main Menu (see 
    “Navigating through the menu” on page 36), 
    then select the item from the sub-menu.
    Remote ControlControl Panel
    Language
    Press ▲▼ to select [Language].1 ) 
    Press ► or the  button.2 ) 
    Press ▲▼ to select the desired 3 ) 
    language.
    The language used in the On-Screen Menu is  z
    available in English, German, French, Italian, 
    Spanish, Portuguese, Dutch, Swedish, Finnish, 
    Norwegian, Danish,  Polish, Hungarian, Romanian, 
    Czech, Russian, Turkish, Arabic, Kazak, 
    Vietnamese, Chinese, Korean, Japanese and Thai.
    Menu position
    This function is used to change the position of the On-
    Screen Menu.
    Press ▲▼ to select [Menu position].1 ) 
    Press the  button to change 2 ) 
    the position.
    The Menu position changes each time you  z
    press  button as follows:
    the center → the bottom left → the bottom right → the 
    top left → the top right → the center......
    Auto setup
    Press ▲▼ to select [Auto setup].1 ) 
    Press ► or the  button.2 ) 
    Press ▲▼ to select these functions as 3 ) 
    follows:
     JInput search
           
    This function detects the input signal automatically. 
    When a signal is found, the search will stop.
    OffInput search will not work
    On 1Input search works*1
    On 2Input search works*2
    ● When pressing the  button on the                                                                                                                                              *1 : 
       remote control or the control panel.            
    ● When turning on the projector by pressing the                                                                                                                                              *2 : 
        button on the remote control or the                                                                                                                                              
        control panel.●●●●●                                                                                                                                     ● When pressing the  button on the                                                                                                                                              
       remote control or the control panel.                                                               
    ● When the current input signal is cut off.*
              *   If the [AV mute] or [Freeze] function is active,  cancel 
    it to activate the Input search. It is also  unavailable 
    when On-Screen menu is displayed.
    Auto PC adj. J
    OnEnables Auto PC adjustment *1
    OffDisables Auto PC adjustment
    When pressing the  button on *1 : 
    the remote control or the control panel.
     Auto keystone
    AutoAlways works and corrects keystone 
    distortion according to the projector's 
    tilt.
    ManualWorks only when pressing the 
     button on the 
    remote control or the control panel. 
    OffDisables Auto Keystone.
    Note
    [Input search], [Auto PC adj.] and [Auto Keystone] cannot  z
    be set [Off] at the same time.
    The [Auto Keystone] function cannot work when the  z
    [Ceiling] feature is set [On] in the [Screen] menu. 
    						
    							Setting
    ENGLISH - 53
    Settings
    Background
    Select the background screen for when no input signal 
    is detected.
    Press ▲▼ to select [Background].1 ) 
    Press the  button.2 ) 
    Press ▲▼ to switch3 )  between each 
    option as below.
    BlueBlue colored background.
    UserThe logo transferred by "Logo
    Transfer Software *1 " is projected.
    BlackBlack colored background.
    " Logo Transfer Software" is included on the *1 : 
    supplied CD-ROM.
    Display
    This function decides whether to display On-Screen 
    Displays.
    Press ▲▼ to select [Display].1 ) 
    Press the  button.2 ) 
    Press ▲▼ to switch3 )  between each 
    option as below.
    OnShow all the On-Screen displays 
    *1
    Countdown 
    off
    Show the input image instead of 
    the countdown when turning on 
    the projector *2
    OffHide the On-Screen Displays *3
    Use this function when you want to project *1 : 
    images after the lamp becomes bright enough. 
    The factory default setting is in this option.
    Use this function when you want to project the *2 : 
    image as early as possible even when the lamp 
    is not bright enough. 
    Hide the On-Screen Displays except;  *3 : 
    ● On-Screen Menu. 
    ● [Power off?]  
    ● [P-timer] display. 
    ● No signal for [Power management]   
    ● [Please wait ...] 
    ●   
    Arrows for the True function in the [Screen] 
    Menu.
    ●   [Service]
    Logo
    This function allows you to customize the screen logo 
    with [Logo select], [Logo PIN code lock] and [Logo 
    PIN code change] functions.
    Press ▲▼ to select [Logo].1 ) 
    Press ► or the  button.2 ) 
    Press ▲▼ to choose the desired item.3 ) 
    Logo select J
    This function decides on the starting-up display from 
    among following options.
    OffShow the countdown display only.
    DefaultShow the factory-set logo.
    UserThe logo transferred by "Logo
    Transfer Software *1 " is projected.
    " Logo Transfer Software" is included on the *1 : 
    supplied CD-ROM.
    Logo PIN code lock J
    This function prevents an unauthorized person from 
    changing the screen logo.
    OffThe screen logo can be changed 
    freely from the Logo Menu.
    OnThe screen logo cannot be changed 
    without a Logo PIN code.
    Note
    If you want to change the Logo PIN code lock setting,  z
    press the  button and the Logo PIN code 
    dialog box appears. Enter a Logo PIN code by following 
    the steps below. The initial Logo PIN code is set to “4321” 
    at the factory.
    Enter a logo PIN code 
     
    Press ▲▼ buttons to enter a number from 0-9. Press ► 
    button to fix the number and move the red frame pointer to 
    the next box. The number changes to . Repeat this step to 
    complete entering a four-digit number.  
    After entering the four-digit number, press ► button to 
    move the pointer to “Set” and then a [OK?] confirmation box 
    appears, select [Yes] and then press  button. 
     
       
       If you fixed an incorrect number, use the ◄ button to  
       move the pointer to the number you want to correct,  
       and then enter the correct number with the ▲▼  
       buttons.
       If you entered an incorrect PIN code, PIN code and the  
        number () will turn red for a moment. Enter the  
        correct PIN code all over again.   
    						
    							Setting
    54 - ENGLISH
    Settings
    Logo PIN code change J
    Logo PIN code can be changed to your desired four-
    digit number.
    Press ▲▼ to select [Logo PIN code 1 ) 
    change] and press the  
    button.
    Current logo PIN code dialog box appears. z
    Press ▲▼ to enter the current code, 2 ) 
    press the ► button to fix the number 
    and move the red frame pointer to the 
    next box.
    The New Logo PIN code input dialog box  z
    appears. 
    Repeat this step to set the new Logo 3 ) 
    PIN code.
    Attention
    Be sure to note the new Logo PIN code and keep it on  z
    hand. If you lost the number, you could no longer change 
    the Logo PIN code setting.
    HDMI setup
    This function is only used for HDMI input source.
    Press ▲▼ to select [HDMI setup].1 ) 
    Press ► or the  button to 2 ) 
    access the submenu.
    Press ▲▼ to switch the item.3 ) 
    Image J
    NormalWhen the output of external 
    equipment is set to Normal.
    EnhancedWhen the output of external 
    equipment is set to Enhanced.
    Sound J
    HDMIWhen Digital input source is input,
    Sound is set to HDMI.
    Computer  
    2
    When DVI input source is changed 
    to HDMI input source, Sound is set 
    to Computer 2.
    Note
    The optimum setting depends on the setting of the  z
    external equipment. For details, refer to the operating 
    instructions of your external equipment.
    Connect the computer 2 audio input signals to  z
    COMPUTER AUDIO IN 1 terminal as Sound function is 
    set to Computer 2 and MIC function is turned on.
    The names for the output setting of Digital R/G/B vary  z
    from equipment to equipment.
    Terminal
    The COMPUTER 2 IN/MONITOR OUT terminal on 
    the back of the projector is switchable for computer 2 
    input or monitor output.
    Press ▲▼ to select [Terminal] and 1 ) 
    then press the  button.
    Press ▲▼ to switch the item.2 ) 
    Computer 2Computer input
    Monitor outMonitor out
    Note
    Terminal function is not available when selecting  z
    [Computer 2] to the input source. Change the input 
    source to the others (HDMI, Computer 1, Video or 
    S-Video) so that the Terminal function will be available.
    Power management
    For reducing power consumption as well as 
    maintaining the lamp life, the Power management 
    function turns off the projection lamp when the 
    projector is not operated for a certain period.
    Press ▲▼ to select [Power 1 ) 
    management].
    Press ► or the  button to 2 ) 
    access the submenu.
    Mode J
    Press ▲▼ and then press the 1 ) 
     button to select one mode 
    among the items as below.
    ReadyWhen the lamp has been fully cooled 
    down, the  
    indicator changes to green blinking. 
    In this condition, the projection lamp 
    will be turned on if the input signal 
    is reconnected or any button on the 
    control panel or remote control is 
    pressed.
    Shut 
    down
    When the lamp has been fully cooled 
    down, the power will be turned off.
    Off[Power management] function is off.
    Timer J
    Press ▲▼ to select [Timer] and then 1 ) 
    press the  button.
    Press ▲▼ to set the Timer(1~30min).2 )  
    						
    							Setting
    ENGLISH - 55
    Settings
    Direct on
    Press ▲▼ to select [Direct on] and 1 ) 
    then press the  button.
    Press ▲▼ to switch between [On] and 2 ) 
    [Off].
    When this function is set to [On], the projector  z
    will be automatically turned on just by 
    connecting the AC power cord to a wall outlet.
    Be sure to turn off the projector properly. If the  z
    projector is turned off in the incorrect sequence, 
    the [Direct On] function does not work properly.
    Standby mode
    This function can set the electric power when the 
    projector is standing by.
    Press ▲▼ to select [Standby mode] 1 ) 
    and then press the  button.
    Press ▲▼ to switch between the items  2 ) 
    as below.
    Eco
    Restricts some functions in 
    standby mode to reduce power 
    consumption.
    NetworkDoes not restrict functionality 
    even in standby mode.
    Note
    When selecting [Network], the cooling fans may be  z
    running depending on the temperature inside the 
    projector even if the projector is turned off.
    If Standby mode is set to [Eco], you cannot use network  z
    functions when the projector is standing by. Also, you 
    cannot use some RS-232C protocol commands.
    If set to [Network], you can use network functions when  z
    the projector is standing by.
    If [Standby mode] is set to [Eco], the signal come from  z
    MONITOR OUT and VARIABLE AUDIO OUT terminals 
    are unavailable.
    P-timer
    This function allows you to change the setting of the 
    P-timer and execute it.
    Press ▲▼ to select [P-timer].1 ) 
    Press ► or  button to access 2 ) 
    the submenu.
    Mode J
    Press ▲▼ button to select one mode 1 ) 
    among the items as below.
    Count up
    The P-timer display 000:00 
    appears on the screen and the 
    count up starts (000:00-180:00).
    Count downThe time set in the Timer setting 
    appears on the screen and the 
    countdown starts.
    Timer J
    Press ▲▼ to select [Timer] and then 1 ) 
    press the  button.
    Press▲▼ to set the [Timer](1-180 min).2 ) 
    Timer is available in [Count down] only. Factory  z
    default value is 10 min.
    Execute J
    Press ▲▼ to select one among the 1 ) 
    items as below and then press the 
     button. 
    StartIt executes the count up or count 
    down function.*1
    ResetReset the P-timer values.*2
    ExitTo exit the P-timer operation.
    Press the  button at Start and the *1 : 
    indication changes into Stop. To stop Count up or 
    Count down, press the  button at Stop 
    on the screen menu, then the indication changes 
    into Restart. Press the  button at 
    Restart to resume Count up or Count down.
    Press the  button at Reset to return to *2 : 
    the following value: 
    Count up"000:00"
    Count downTimer that you set
    Note
    To stop the [P-timer] function, press the   z
    button.
    To cancel the [P-timer], press and hold the   z
    button for a few seconds. 
    						
    							Setting
    56 - ENGLISH
    Settings
    Closed caption
    [Only for NTSC, 480i input]
    Press ▲▼ to select [Closed caption].1 ) 
    Press ► or the  button to 2 ) 
    enter the submenu.
    Closed caption J
    Press ▲▼ to select [Closed caption] 1 ) 
    and then press the  button.
    Press ▲▼ to select [Off], [CC 1],  2 ) 
    [CC 2], [CC 3] or [CC 4].
    Color J
    Press ▲▼ to select [Color] and then 1 ) 
    press the  button.
    Press▲▼ to select [color] or [white].2 ) 
    Note
    The closed caption is mainly used in the north America.  z
    This function shows the text  information contained in the 
    image signal. Captions may not be displayed on some 
    devices or software.
    You can select [Closed caption] when matching signals  z
    for the closed caption are input.
    Part of characters may not displayed when high  z
    compensation values are set in [Keystone].
    Closed captions are not displayed while the menu screen  z
    appears.
    Lamp power
    This function allows you to change brightness of the 
    screen.
    Press ▲▼ to select [Lamp power] and 1 ) 
    then press the  button .
    Press ▲▼ to select one among the 2 ) 
    modes as below.
    You can also press the  button to  z
    display [Lamp power].
               NormalNormal brightness.
          Eco
    Lower brightness reduces the 
    lamp power consumption and 
    extends the lamp life.
    Remote control
    This switching function prevents remote control 
    interference when operating several projectors or 
    video equipment at the same time.
    Press ▲▼ to select [Remote control].1 ) 
    Press ► or the  button.2 ) 
    Press ▲▼ to select one among the 3 ) 
    seven codes. 
    This projector provides 7 different remote  z
    control codes: [ALL], [Code 1]~[Code 6].
    Attention
    When operating the projector under [ALL] code, you can  z
    operate several projectors at the same time. If you want 
    to operate the projector independently, you must switch 
    to other code.
    When different codes are set on the projector and on the  z
    remote control, any operation cannot be made. In that 
    case, switch the code on the remote control to fit the 
    code on the projector.
    If the batteries are removed from the remote control for a  z
    long period of time, the remote control code will be reset.
    Security
    This function allows you to use the Key lock and PIN 
    code lock function to set the security for the projector 
    operation.
    Press ▲▼ to select [Security].1 ) 
    Press ► or the  button to 2 ) 
    access the submenu.
    Key lock J
    This function locks the control panel and remote 
    control buttons to prevent operation by unauthorized 
    persons.
    Press ▲▼ to select the desired items 1 ) 
    as below.
    Unlocked.
    Lock the operation of the control 
    panel. To unlock, use the remote 
    control.
    Lock the operation of the remote 
    control. To unlock, use the control 
    panel. 
    						
    							ENGLISH - 57
    Settings
    Setting
    PIN code lock J
    This function prevents the projector from being 
    operated by unauthorized persons and provides the 
    following setting options for security.
    Press ▲▼ to select the desired items 1 ) 
    as below.
    OffUnlocked.
    On 1Enter the PIN code every time 
    turning on the projector.
    On 2
    Enter the PIN code to operate 
    the projector once the power cord 
    is disconnected; as long as the 
    AC power cord is connected, the 
    projector can be operated without 
    a PIN code.
    Note
    Whenever you change the PIN code lock setting or the  z
    PIN code (the four-digit number), you are required to 
    enter the PIN code. The "1234" is set as the initial PIN 
    code at the factory.
    Enter a PIN code  
    Press ▲▼ buttons to enter a number from 0-9. Press ► button to fix the number and move the red frame pointer to the next box. The number changes to . Repeat this step to complete entering a four-digit number.  After entering the four-digit number, press ► button to move the pointer to “Set” and then a [OK?] confirmation box appears, select [Yes] and then press  button.     
       If you fixed an incorrect number, use the ◄ button to      move the pointer to the number you want to correct,      and then enter the correct number with the ▲▼      buttons.  If you entered an incorrect PIN code, PIN code and the      number () will turn red for a moment. Enter the    
       correct PIN code all over again. 
    PIN code change J
    The PIN code can be changed to your desired four-
    digit number.
    Press ▲▼ to select [PIN code change] 1 ) 
    and then Press  button.
    Current Pin code dialog box appears. z
    Press ▲▼ to enter the current code. 2 ) 
    Press ► button to fix the number and 
    move the red frame pointer to the next 
    box. 
    The New PIN code input dialog box appears. z
    Repeat these steps to set a new PIN 3 ) 
    code.
    Attention
    Be sure to note the new PIN code and keep it on hand. If  z
    you lost the number, you could no longer change the PIN 
    code setting.
    Fan 
    Press ▲▼ to select [Fan] and then 1 ) 
    Press  button.
    Press ▲▼ to select one option .2 ) 
    This function provides the following options in  z
    the cooling fans’ operation when the projector is 
    turned off.
    L 1
    Higher-sound than L 2 mode 
    and it takes less time to cool the 
    projector down.
    L 2
    Slower and lower-sound than  
    L 1 mode, but it takes more time 
    to cool the projector down.
    Fan control
    Press ▲▼ to select [Fan control] and 1 ) 
    then Press  button.
    Press ▲▼ to select one among 2 ) 
    options as below.
    Choose the running speed of cooling fans from  z
    the following options according to the ground 
    elevation under which you use the projector.
    OffNormal speed.*1
    On 1Faster than [Off] mode.*2
    On 2Faster than [On 1] mode.*3
    Set this function to [Off] when using the projector *1 : 
    in non-high altitude environment.
    When using the projector in the elevation of *2 : 
    above 1 200 m and below 2 000 m, make sure 
    [Fan control] is set to [On 1].
    When using the projector in the elevation of *3 : 
    above 2 000 m and below 2 700 m, make sure 
    [Fan control] is set to [On 2].
    Note
    Failure to set the running speed of cooling fans  z
    properly may affect the projector life.
    The fan noise becomes louder in [On 1] and [On 2]. z
    Video delay control
    This function allows you to make a digital processing 
    of a projected image faster.
    Press ▲▼ to select [Video delay 1 ) 
    control] and then Press the  
    button.
    Press ▲▼ to select one item between 2 ) 
    [On] and [Off]. 
    						
    							Setting
    58 - ENGLISH
    Settings
    Note
    [Noise reduction] and [Progressive] can not be  z
    selected when [Video delay control] function is set 
    to [On].
    Filter counter
    This function is used to set a frequency for the filter 
    replacement.
    Press ▲▼ to select [Filter counter].1 ) 
    Press ►or the  button to 2 ) 
    access the submenu items.
    Filter counter J
    Show the total accumulated time of the filter use timer 
    setting.
    Timer J
    To set a timer. When the projector reaches the 
    selected time the filter warning icon  appears on the 
    screen.
    Press ▲▼ to select [Timer] and then 1 ) 
    press the  button.
    Press ▲▼ to set the Timer.2 ) 
    Select from [Off/1000H/2000H/3000H/  z
    4000H/5000H/6000H] depending on the use 
    environment.
    Filter counter reset J
    After replacing the filter, be sure to reset the timer.
    Press ▲▼ to select [Filter counter 1 ) 
    reset].
    Press the  button. 2 ) 
    [Filter counter Reset?] appears. Select [Yes]  z
    to continue. Another confirmation dialog 
    box appears, select [Yes] to reset the [Filter 
    counter].
    Emulate
    When using the control commands for one of our 
    projectors that you have previously purchased to 
    control this projector using a computer via its serial 
    input terminal , set up the [Emulate] function as 
    follows. This will allow you to use the control software 
    etc. designed for our existing projectors.
    Press ▲▼ to select [Emulate].1 ) 
    Press the  button or the ► 2 ) 
    button.
    The [Emulate] screen appears. z
    Press ▲▼ to select the required item.3 ) 
    Press the  button.4 ) 
    Note
    Refer to "Serial terminal" ( zÆpage 88)
    Default
    VW440 series, VX510 series
    VW430 series, VX500 series
    VW435N series, VX505N series
    D3500D3500 series
    D4000D4000 series
    D/W5k 
    series
    D5500 series,
    DW5000 series, D5600 series,
    DW5100 series, D5700 series
    D/W/Z6k 
    series
    D5000 series, D6000 series,
    DW6300 series, 
    DZ6700 series,
    DZ6710 series,
    DZ570 series, 
    DW530 series,
    DX500 series
    L730L520 series,
    L720 series, L730 series
    L780L750 series, L780 series
    L735L735 series
    L785L785 series
    LB/W series
    LB2 series, LB1 series,
    LB75 series, LB80 series, 
    LB90 series, ST10 series
    F/W series
    FX400 series, FW430 series, 
    F100 series, FW100 series,
    F200 series, F300 series,
    FW300 series
    LZ370LZ370 series 
    						
    							Setting
    ENGLISH - 59
    Settings
    Warning log
    This function records anomalous operations while the 
    projector is in operation and use it when diagnosing 
    faults.
    Press ▲▼ to select [Warning log].1 ) 
    Press ► or the  button to 2 ) 
    display the latest warning message.
    Up to 10 warning logs are displayed with the  z
    latest warning message at the top of the list, 
    followed by previous warning messages in 
    chronological order.
    Note
    When the [Factory default] function is executed, all  z
    the warning log records will be deleted.
    Factory default
    This function returns all setting values except for [PIN 
    code lock], [Logo PIN code lock], [Lamp power], [Filter 
    counter] and all of the network settings to the factory 
    default settings.
    Press ▲▼ to select [Factory default].1 ) 
    Press the  button.2 ) 
    [Return to Factory default?] appears. Select  z
    [Yes] to continue. Another confirmation dialog 
    box appears, select [Yes] to return to [Factory 
    default]. 
    						
    							60 - ENGLISH
    Settings
    Select [Information] from the Main Menu (see 
    “Navigating through the menu” on page 36).
    Remote ControlControl Panel
    Input Source Information 
    Display 
    The Information Menu is used for checking the status 
    of the image signal being projected and the operation 
    of the projector.
    You can also Press the  button on the remote 
    control to display the Information menu.
    Press ◄► to switch between page 1 and 
    page 2.
    Input J
    The selected input source is displayed.
    System J
    The selected system is displayed.
    H-sync freq. J
    The selected H-sync freq. is displayed.
    The horizontal frequency of the input signal is 
    displayed in KHz, or - - - - KHz when no signal.
    V-sync freq. J
    The selected V-sync freq. is displayed.
    The vertical frequency of the input signal is displayed 
    in Hz, or - - - - Hz when no signal. 
    Screen J
    The selected Screen size is displayed.
    Language J
    The selected language is displayed.
    Lamp power J
    The selected lamp mode is displayed.
    Lamp runtime J
    The cumulative lamp operating time is displayed.
    Power management J
    [Off] , [Ready] or [Shut down], and [Timer] are 
    displayed.
    Key lock J
    The selected Key lock icon is displayed.
    PIN code lock J
    [Off], [On 1] or [On 2] is displayed.
    Remote control J
    The selected remote control code is displayed.
    Serial number J
    The serial number of the projector is displayed.
    The serial number is used to service the projector.
    Information 
    						
    All Panasonic manuals Comments (0)

    Related Manuals for Panasonic LCD Projector Pt Vw440 Operating Instructions