Panasonic LCD Projector Pt Vw435NE Operating Instructions

							ENGLISH - 61
Settings
Setting
Security
This function allows you to use the Key lock and PIN 
code lock function to set the security for the projector 
operation.
Press ▲▼ to select [Security].
1  ) 
Press ► or the  button to 
2  ) 
access the submenu.
Key lock 
J
This function locks the control panel and remote 
control buttons to prevent operation by unauthorized 
persons.
Press ▲▼ to select the desired items 
1  ) 
as below.
Unlocked.
Lock the operation of the control 
panel. To unlock, use the remote 
control.
Lock the operation of the remote 
control. To unlock, use the control 
panel.
PIN code lock 
J
This function prevents the projector from being 
operated by unauthorized persons and provides the 
following setting options for security.
Press ▲▼ to select the desired items 
1  ) 
as below.
Off Unlocked.
On 1 Enter the PIN code every time 
turning on the projector.
On 2 Enter the PIN code to operate 
the projector once the power cord 
is disconnected; as long as the 
AC power cord is connected, the 
projector can be operated without 
a PIN code.
Attention
Whenever you change the PIN code lock setting or the 
 
z
PIN code (the four-digit number), you are required to 
enter the PIN code. The "1234" is set as the initial PIN 
code at the factory.
You can enter a PIN code through the control panel or 
 
z
the remote control. For details, please refer to "Enter a 
PIN code" (
Æ page 33). 
PIN code change 
J
The PIN code can be changed to your desired four-
digit number.
Press ▲▼ to select [PIN code change] 
1  ) 
and then Press  button.
Current Pin code dialog box appears. 
z
Press ▲▼ to enter the current code. 
2  ) 
Press ► button to fix the number and 
move the red frame pointer to the next 
box. 
The New PIN code input dialog box appears. 
z
Repeat these steps to set a new PIN 
3  ) 
code.
Attention
Be sure to note the new PIN code and keep it on hand. If 
 
z
you lost the number, you could no longer change the PIN 
code setting.
Fan 
Press ▲▼ to select [Fan] and then 
1  ) 
Press  button.
Press ▲▼ to select one option .
2  ) 
This function provides the following options in  
z
the cooling fans’ operation when the projector is 
turned off.
L 1 It takes less time to cool the 
projector down than L 2 mode.  
L 2 Slower and lower-sound than L 1 
 
mode, but it takes more time to 
cool the projector down.
Fan control
Press ▲▼ to select [Fan control] and 
1  ) 
then Press  button.
Press ▲▼ to select one among 
2  ) 
options as below.
Choose the running speed of cooling fans from  
z
the following options according to the ground 
elevation under which you use the projector.
Off Normal speed.*1
On 1 Faster than [Off] mode.*2
On 2Faster than [On 1] mode.*3
Set this function to [Off] when using the projector 
*1 : 
in non-high altitude environment.
When using the projector in the elevation of 
*2 : 
above 1 200 m and below 2 000 m, make sure 
[Fan control] is set to [On 1]. 
						

							Setting
62 - ENGLISH
Settings
When using the projector in the elevation of 
*3 : 
above 2 000 m and below 2 700 m, make sure 
[Fan control] is set to [On 2].
Note Failure to set the running speed of cooling fans 
 
z
properly may affect the projector life.
The fan noise becomes louder in [On 1] and [On 2].
 
z
Video delay control
This function allows you to make a digital processing 
of a projected image faster.
Press ▲▼ to select [Video delay 
1  ) 
control] and then Press the  
button.
Press ▲▼ to select one item between 
2  ) 
[On] and [Off].
Note
[Noise reduction] and [Progressive] can not be 
 
z
selected when [Video delay control] function is set 
to [On].
Filter counter
This function is used to set a frequency for the filter 
replacement.
Press ▲▼ to select [Filter counter].
1  ) 
Press ►or the  button to 
2  ) 
access the submenu items.
Filter counter 
J
Show the total accumulated time of the filter use timer 
setting.
Timer 
J
To set a timer. When the projector reaches the 
selected time the filter warning icon appears on the 
screen.
Press ▲▼ to select [Timer] and then 
1  ) 
press the  button.
Press ▲▼ to set the Timer.
2  ) 
Select from [Off/1000H/2000H/3000H/   
z
4000H/5000H/6000H] depending on the use 
environment.
Filter counter reset 
J
After replacing the filter, be sure to reset the timer.
Press ▲▼ to select [Filter counter 
1  ) 
reset].
Press the  button. 
2  ) 
[Filter counter Reset?] appears. Select [Yes]  
z
to continue. Another confirmation dialog 
box appears, select [Yes] to reset the [Filter 
counter].
Emulate
When using the control commands for one of our 
projectors that you have previously purchased to 
control this projector using a computer via its serial 
input terminal, set up the [Emulate] function as 
follows. This will allow you to use the control software 
etc. designed for our existing projectors.
Press ▲▼ to select [Emulate].
1  ) 
Press the  button or the ► 
2  ) 
button.
The [Emulate] screen appears. 
z
Press ▲▼ to select the required item.
3  ) 
Press the  button.
4  ) 
Note
Refer to "Serial terminal" (
 
z
Æpage 103)
Default VW430 series, VX500 series, 
VW435N series, VX505N series
D3500 D3500 series
D4000 D4000 series
D/W5k  series D5500 series,
DW5000 series, D5600 series,
DW5100 series, D5700 series
D/W/Z6k  series D5000 series, D6000 series,
DW6300 series, 
DZ6700 series,
DZ6710 series,
DZ570 series, 
DW530 series,.
DX500 series
L730 L520 series,
L720 series, L730 series
L780 L750 series, L780 series
L735 L735 series 
						

							Setting
ENGLISH - 63
Settings
L785L785 series
LB/W series LB2 series, LB1 series,
LB75 series, LB80 series, 
LB90 series, ST10 series
F/W series FX400series, FW430 series, 
F100 series, FW100 series,
F200 series, F300 series,
FW300 series
LZ370 LZ370 series
Warning log
This function records anomalous operations while the 
projector is in operation and use it when diagnosing 
faults.
Press ▲▼ to select [Warning log].
1  ) 
Press ► or the  button to 
2  ) 
display the latest warning message.
Up to 10 warning logs are displayed with the  
z
latest warning message at the top of the list, 
followed by previous warning messages in 
chronological order.
Attention When the [Factory default] function is executed, all 
 
z
the warning log records will be deleted.
Factory default
This function returns all setting values except for [PIN 
code lock], [Logo PIN code lock], [Lamp runtime], 
[Filter counter], the logo transferred by "Logo Transfer 
Software" and all of the network settings to the factory 
default settings.
Press ▲▼ to select [Factory default].
1  ) 
Press the  button.
2  ) 
[Return to Factory default?] appears. Select  
z
[Yes] to continue. Another confirmation dialog 
box appears, select [Yes] to return to [Factory 
default]. 
						

							64 - ENGLISH
Settings
Select [Information] from the Main Menu (see 
“Navigating through the menu” on page 40), 
then select the item from the sub-menu.
Remote ControlControl Panel
Input Source Information 
Display 
The Information Menu is used for checking the status 
of the image signal being projected and the operation 
of the projector.
You can also Press the  button on the remote 
control to display the Information menu.
Input 
J
The selected input source is displayed.
System 
J
The selected system is displayed.
H-sync freq. 
J
The selected H-sync freq. is displayed.
The horizontal frequency of the input signal is 
displayed in kHz, or - - - - kHz when no signal.
V-sync freq. 
J
The selected V-sync freq. is displayed.
The vertical frequency of the input signal is displayed 
in Hz, or - - - - Hz when no signal. Numbers of Hz 
doubles when during Interlace.
Screen 
J
The selected Screen size is displayed.
Language 
J
The selected language is displayed.
Lamp power 
J
The selected lamp mode is displayed.
Lamp runtime 
J
The cumulative lamp operating time is displayed.
Power management 
J
[Off] , [Ready] or [Shut down], and [Timer] are 
displayed.
Key lock 
J
The selected Key lock icon is displayed.
PIN code lock 
J
[Off], [On 1] or [On 2] is displayed.
Remote control 
J
The selected remote control code is displayed.
Serial number 
J
The serial number of the projector is displayed.
The serial number is used to service the projector.
Information 
						

							ENGLISH - 65
Settings
Network
Select [Setting] from the Main Menu (see 
“Navigating through the menu” on page 40), 
then select the item from the sub-menu.
Remote ControlControl Panel
Verifying the network information
When connecting the projector via the dedicated 
applications of "Wireless Manager mobile edition 6.0” 
or iPad / iPhone / iPod touch, the network number, the 
project name and ID of Wireless LAN are required. 
You can check these information by entering [Input 
Guide] or [Network Status]. (
Æpage 70)
To display the input guide, please press the [INPUT] 
button on the control panel or any one of the input 
selection buttons on the remote control.
Wired LAN
You can make detailed wired LAN settings.
Press ▲▼ to select [Wired LAN], and 
1  ) 
press  button.
Press ▲▼ to select an item, and 
2  ) 
change the setting according to the 
instructions.
DHCP(DHCP client 
function)
On: If a DHCP server 
exists in the 
network to which 
the projector is 
connected, the 
IP address will 
automatically be 
acquired.
Off: If a DHCP 
server does 
not exist in the 
network to which 
the projector 
is connected, 
additionally set 
[IP address], 
[Subnet mask 
] and [ Default 
gateway  ].
IP address
(Display of IP 
address and setting)Enter the IP address 
if DHCP server is not 
used.
Subnet mask
(Displaying and 
setting the subnet 
mask)If not using a DHCP 
server, enter the subnet 
mask.
Default gateway
  (Display of gateway 
address and setting)Enter the gateway 
address if DHCP server 
is not used.
DNS1

(Display of 
Preferred DNS 
server address 
and setting) Enter the DNS server 
address if DHCP server 
is not used.
DNS2
 (Display 
of Alternate DNS 
server address 
and setting) Enter the alternate DNS 
server address if DHCP 
server is not used.
“Glossary” (
 
Æpage  115 – 116)
Press ▲▼◄► to select [Set], and press 
3  ) 
 button.
Default wired LAN settings  
z 
The following settings are set before the 
projector leaves the factory.
DHCP  Off
IP address 1 9 2 .1 6 8 .1 0 .1 0 0
Subnet mask 255.255.255.0
Default gateway 1 9 2 .1 6 8 .1 0 .1
DNS 1 / DNS 2 NONE
Input Guide
Network number of wireless LAN
(Left) Projector name
(Right) Projector ID 
						

							Network
66 - ENGLISH
Settings
Note
Before using the DHCP server, make sure the DHCP 
 
z
server is already functioning.
For details of IP address, subnet mask, gateway and 
 
z
DNS, ask the network administrator
.
A wired LAN and wireless LAN can not be used in the 
 
z
same segment.
Wireless LAN
You can set the network number.
Press ▲▼ to select [Wireless LAN], 
1  ) 
and press  or ► button.
Select the number to be connected 
2  ) 
with the ▲▼ buttons.
Network number [Off], [S-DIRECT],  
z
[M-DIRECT], [S-MAP], [1]-[4], [User 1]-
[User 3]
Note
Selecting [Off] disables the wireless LAN.
 
z
Network number: [S-DIRECT], [S-MAP] and [1]-[4] are 
 
z
available only when connecting via wireless LAN with 
the application software the “Wireless Manager mobile 
edition 6.0”. For details, refer to the operation manual of 
the “Wireless Manager mobile edition 6.0”.
Network number: [USER 1]-[USER 3] can be changed in 
 
z
[Wireless detailed setup] menu. (
Æpage 66-69)
Wireless detailed setup
You can configure more precise network settings, if 
you select [M-DIRECT] or [USER1]~[USER3] (user) 
for [Wireless LAN] in the network menu. For network 
settings, contact your network administrator.
Configuration of Wireless LAN 
 
„
[M-DIRECT]
Even if there is no access point, you can still 
connect the projector to computer via the 
infrastructure. In addition, the connection with iPad 
/ iPhone / iPod touch is much easier. For details, 
please refer to [Sending image from iPad / iPhone 
/ iPod touch]. (
Æpage  69)
Press ▲▼ to select [Wireless detailed 
1  ) 
setup], and press  button.
Press ▲▼ to select an item, and 
2  ) 
change the setting according to the 
instructions.
IP Address 
(Displaying and 
setting the IP address)Enter the IP address.
Subnet Mask (Displaying and 
setting the subnet 
mask)Enter the subnet mask.
SSID 
(Displaying and 
setting the SSID)Select M-DERECT in 
Wireless LAN, then the 
SSID can be set.
Channel Select M-DERECT in 
Wireless LAN, then the 
Channel can be set. 
Select a channel for the 
access point (
Æ page 
19). 
KEY Select M-DERECT 
in Wireless LAN, 
then the KEY can 
be set. Setting a key 
for the access point. 
Input either 8 to 63 
alphanumerics or a 
64 digit string in the 
hexadecimal format.
“Glossary” (
 
Æpage  115 – 116)
Press ▲▼◄► to select [SET], and 
3  ) 
press  button.
The current setting of network will be saved.
Note
After the configuration is completed, you must select 
 
z
[SET] and press the  button. At this time, if you 
select [Cancel], You will cancel the setting change.
Default settings of 
 
„[M-DIRECT]
The following settings as [M-DIRECT] in the 
wireless LAN are set before the projector leaves 
the factory.
IP Address 1 9 2 .1 6 8 .12 .1 0 0
Subnet Mask 
255.255.255.0
SSID 
M-DIRECT + The last 4 digits 
of the projector ID
Channel 1
KEY The same string as the SSID
Note
The authentication method is WPA2-PSK, and the 
 
z
encryption method is AES. Both methods are fixed.
When you need to change initial configuration of 
 
z
[M-DIRECT], please contact your network administrator.
Make sure the initial Key is changed for safety.
 
z
As the DHCP server is already functioning, select [ON] 
 
z
before connecting a computer.
Configuration of Wireless LAN 
 
„
[USER1]~[USER3]
Press ▲▼ to select [Wireless detailed 
1  ) 
setup], and press  button. 
						

							Network
ENGLISH - 67
Settings
Press ▲▼ to select an item, and 
2  ) 
change the setting according to the 
instructions.
Name change You can change the user 
name.
DHCP 
(DHCP client 
function)
ON: If a DHCP server 
exists in the 
network to which 
the projector is 
connected, the 
IP address will 
automatically be 
acquired.
OFF: If a DHCP server 
does not exist in 
the network to 
which the projector 
is connected, 
additionally set [IP 
address  
], [Subnet 
mask ] and 
[Default gateway ].
IP address 
(Display of IP 
address and 
setting)Enter the IP address if 
DHCP server is not used.
Subnet mask 
(Displaying and 
setting the subnet 
mask)If not using a DHCP 
server, enter the subnet 
mask. 
Default gateway  
(Display of 
gateway address 
and setting)Enter the gateway address 
if DHCP server is not 
used.
DNS1
(Display of 
Preferred DNS 
server address and 
setting)Enter the DNS server 
address if DHCP server is 
not used.
DNS2 
(Display of 
Alternate DNS 
server address and 
setting)
Enter the alternate DNS 
server address if DHCP 
server is not used.
“Glossary” (
 
Æpage  115 – 116)
Note
Before using the DHCP server, make sure the DHCP 
 
z
server is already functioning.
For details of IP address, subnet mask, gateway and 
 
z
DNS server, ask the network administrator.
A wired LAN and wireless LAN cannot be used in the 
 
z
same segment.
Press ▲▼◄► to select [Next], and 
3  ) 
press  button.
[Wired detailed setup] screen (2/3) setting screen 
is displayed.
Make the settings related to the wireless 
connection between the projector and the network.
Select [Cancel] instead of [Next] to cancel the 
configuration change.
SSID 
 
z
If the mode is [AD HOC], 
enter the same character 
string as that of SSID set 
on the computer to be 
connected. If the mode is 
[Infrastructure 
], enter 
the SSID registered at the 
access point 
.
“Glossary” (
 
Æpage  115 – 116)
Note
SSID has to be entered in alphanumeric letters.
 
z
You cannot set “any” or “ANY” for SSID.
 
z
Mode
 
zSelect [AD HOC] or 
[Infrastructure].
AD HOC 
Connect projector and 
computer directly without 
access point.
Infrastructure 
Connect through access 
point.
“Glossary” (
 
Æpage  115 – 116)
Authentication
 
z
Set the user 
authentication method 
used by the network to 
be connected.
OPEN Select when making 
a connection using 
[AD HOC], or when 
the access point 
authentication method 
is OpenSystem 
1.
SHARED Select when making 
a connection using 
[AD HOC], or when 
the access point 
authentication method 
is Shared Key 
1.
WPA-PSK 
2
Select when the 
access point 
authentication method 
is WPA-PSK 
1.
WPA2-PSK 
2
Select when the 
access point 
authentication method 
is WPA2-PSK 
1.
W PA - E A P/  
WPA2-EAP 
2
Select when the 
access point 
authentication method 
is WPA-EAP 
1/
WPA2-EAP 1.
WPA-EAP 
2
Select when the 
access point 
authentication method 
is WPA-EAP 
1. 
						

							Network
68 - ENGLISH
Settings
WPA2-EAP 2
Select when the 
access point 
authentication method 
is WPA2-EAP 
1.
Encryption
 
z
Select the encryption 
method to be used for 
communication between 
the projector and the 
network.
NONE Select when transmit 
without encryption. It is 
selectable only when 
[Authentication] is [OPEN] 
or [SHARED].
WEP 
1Select when Encryption is 
W E P.
TKIP 
1
Select when Encryption is 
TKIP.
Selectable when 
[Authentication] is either 
[WPA-PSK], [WPA2-
PSK],  [WPA-EAP], 
[WPA2-EAP].
AES 
1
Select when Encryption is 
AES.
Selectable when 
[Authentication] is either 
[WPA-PSK], [WPA2-
PSK],  [WPA-EAP], 
[WPA2-EAP].
Channel 
3Select the channel to use. 
Refer to page 6 for usable 
channels. 
1: “Glossary” (
 
Æpage  115 – 116)
2:   Available when the mode is set to 
 

[Infrastructure].
3:   Available when the mode is set to [AD HOC].
 

Note
Important video/audio data is protected because AES 
 
z
encryption processing takes place in advance for all 
network numbers, even if [Encryption] is set to [NONE].
Press ▲▼◄► to select [Next], and 
4  ) 
press  button.
At this point, select [Back] to go back to the 
previous screen (1/3), or select [Cancel] to cancel 
the configuration change.
In addition, further perform the following setting 
depending on [Authentication] and [Encryption] 
settings.
Note
The setting menu is different depending on the setting 
 
z
of [Authentication] and [Encryption]. The above menu is 
an example when [Authentication] is set to [OPEN] or 
[SHARED] and [Encryption] is set to [WEP].
When setting [OPEN] or [SHARED] 
 
z
as authentication and setting 
[WEP] as the encryption method:
Default key Set 1 – 4 numerals for the 
default key.
KEY1 – 4 Set a WEP key to the key 
number selected with 
[Default key].
Either the 64-bit or 128-bit 
WEP key can be set. For 
the 64-bit key, input five 
alphanumerics (or a 10-digit 
string for the hexadecimal 
format) for the 128-bit key, 
input 13 alphanumerics 
(or a 26-digit string for the 
hexadecimal format).
When using [WPA-PSK] or 
 
z
[WPA2-PSK] : 
Set a key.
Input either 8 to 63 
alphanumerics or a 64 digit 
string in the hexadecimal 
format.
When the authentication method 
 
z
is [WPA-EAP/WPA2-EAP], [WPA-
EAP], [WPA2-EAP]: 
						

							Network
ENGLISH - 69
Settings
Set [EAP], [USER NAME], 
and [PASSWORD].
EAP 1:Select the EAP 
setup in the 
RADIUS server 
1. Types of 
EAP that can be 
selected are as 
follows.
PEAP 
1(MS-
CHAPv2 1), 
PEAP 1(GTC 1), 
EAP-TTLS 
1(MD5 1), 
EAP-TTLS 
1(MS-CHAPv2 1), EAP-FAST 1(MS-CHAPv2 1), EAP-FAST 1(GTC 1) 
USER 
NAME: Input a user 
name used for 
authentication 
(excluding 
spaces)
(maximum 64 
characters).
PAS S  
WORD: Input a password 
used for 
authentication 
(maximum 64 
characters).
1: “Glossary” (
 
Æpage  115 – 116)
Note
If you are unable to connect to the wireless LAN 
 
z
through the access point even after performing the 
steps in “Projector settings (
Æpage  74)”, contact the 
manufacturer of the access point.
When using EAP, the projector needs to be set according 
 
z
to the setting of the RADIUS server. Check with the 
network administrator for the setting of the RADIUS 
server.
When using an EAP together with an access point with 
 
z
invalid SSID broadcast, select WAP-EAP or WAP2-EAP 
for the authentication method even if the authentication 
method of the access point is WPA-EAP/WPA2-EAP.
Default settings of [USER 1]~[USER 3]
 
„
The following settings as [USER1]~[USER3] in the 
wireless LAN are set before the projector leaves 
the factory.
SSID Panasonic Projector
DHCP Off
IP address 1 9 2 .1 6 8 .11.1 0 0
Subnet mask 255.255.255.0
Default gateway1 9 2 .1 6 8 .11.1
Mode AD HOC
Authentication OPEN
Encryption NONE
Channel 11
DNS 1/DNS 2 NONE
Press ▲▼◄► to select [Set], and press 
5  ) 
 button.
Save the current network settings
Note
When configuration is completed, you need to select [Set] 
 
z
and press the  button. At this point, select [Back] 
to go back to the previous screen (2/3), or select [Cancel] 
to cancel the configuration change.
Sending image from iPad / iPhone / 
 
„
iPod touch
By using the dedicated application, you can send the 
PDF file or the JPEG image which stored on your iPad 
/ iPhone / iPod touch to the projector for projecting. 
For details, please enter the following URL.
http://panasonic.net/avc/projector/
Projector name
You can change the projector name to be displayed 
on the network.
Press ▲▼ to select [Projector name], 
1  ) 
and press  button.
Select characters with the ▲▼◄► 
2  ) 
buttons and press the  
button to enter the projector name. 
Select [BS] to delete one character selected 
with the cursor in the input box and press the 
 button.
Select [Set] with the ▲▼◄► buttons 
3  ) 
and press the  button.  
Select [Cancel] to undo the changes and then 
press the  button.
Select [YES] or [No] with the ▲▼ 
4  ) 
buttons and press the  
button.
Note
[Name 
 
z ØØØØ] (
ØØØØ
 is four-digit number) is set 
before the projector leaves the factory. 
						

							Network
70 - ENGLISH
Settings
Password
By controlling connection with password setting, it is 
 
z
possible to prevent an external device from accidentally 
connecting and interrupting projection images, etc.
Set to [On] to perform password check when connecting 
 
z
with the projector using “Wireless Manager mobile edition 
6.0”. (Default : [Off])
When using the deliver image to all function or the 
 
z
delivered image deletion function of the “Multi Projector 
Monitoring & Control Software”, image cannot be 
delivered to the projector with password setting set to 
[On]. To use these image delivery functions, set it to [Off].
Press ▲▼ to select [Password]. Press 
1  ) 
 button or the ► button to 
access to the submenu.
Press ▲▼ to select [Password] and 
2  ) 
press the  button.  
Select [On] or [Off] with ▲▼buttons.
Press ▲▼ to select [Password change], 
3  ) 
and press  button. 
Select characters with the ▲▼◄► 
buttons and press the  
button to enter the password. 
Select [BS] to delete one character selected 
with the cursor in the input box and press the 
 button.
After inputting the password, select 
4  ) 
[OK] using the ▲▼◄► buttons and 
then press  button.






 Select [Cancel] to undo the changes and then 
press the  button.
Network control
Set when you want to control the projector from a 
computer connected to the network.
Press ▲▼ to select [Network control].
1  ) 
Press  button to select [On] 
2  ) 
or [Off] with the ▲▼ buttons.
Live mode cut in
Set this [On] to allow interrupt of the Live mode by 
other users, or to allow delivery of images by the 
“Multi Projector Monitoring & Control Software”, 
while the Live mode is active (sending image) by the 
“Wireless Manager mobile edition 6.0”. For details, 
refer to “Wireless Manager mobile edition 6.0” 
operating manual.
Press ▲▼ to select [Live mode cut in].
1  ) 
Press  button to select [On] 
2  ) 
or [Off] with the ▲▼ buttons.
Note
If you use the “Wireless Manager mobile edition 6.0” 
 
z
and the “Multi Projector Monitoring & Control Software” 
on the same computer at the same time, the function 
of delivering image to all may not be available. If you 
want to use them at the same time, please  use another 
computer with respective software.
Multi-live
Switch to the Multi-live mode when using the 
“Wireless Manager mobile edition 6.0”. See the 
“Wireless Manager mobile edition 6.0” operation 
manual for details.
Press ▲▼ to select [Multi-live]. 
1  ) 
Press  button.
2  ) 
Network status
Displays the current network status.
Press ▲▼ to select [Network status].
1  ) 
Press  button or the ► button 
2  ) 
to access to the submenu.
Each press of the ► button switches  
3  ) 
wired LAN and wireless LAN.
Note
When the network number is set to [Off], [Network status] 
 
z
is not display.