Panasonic LCD Projector Pt Tw343 Operating Instructions
Here you can view all the pages of manual Panasonic LCD Projector Pt Tw343 Operating Instructions. The Panasonic manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 31
ENGLISH - 31 terminal pin assignments and signal names Outside viewPin No.Signal namesPin No.Signal names Even-numbered pins to Odd-numbered pins to T.M.D.S data 2+T.M.D.S clock shield T.M.D.S data 2 shieldT.M.D.S clock - T.M.D.S data 2-CEC T.M.D.S data 1+— T.M.D.S data 1 shieldSCL T.M.D.S data 1-SDA T.M.D.S data 0+DDC/CEC GND T.M.D.S data 0 shield+ 5 V T.M.D.S data 0-Hot plug detection T.M.D.S clock + Connecting example : AV equipment Attention fAlways use one of the following when connecting a...
Page 32
32 - ENGLISH Connecting example : Computers Audio equipmentComputer Control computerComputerControl computer Computer Computer Computer USB memory / Wireless module (Model No.: ET-WML100) Attention fWhen connecting the projector to a computer or an external device, use the power cord supplied with each device and commercially available shielded cables. Note fIf you operate the projector using the computer with the resume feature (last memory), you may have to reset the resume feature to operate the...
Page 33
ENGLISH - 33 Chapter 3 Basic Operations This chapter describes basic operations to start with.
Page 34
![Page 34
34 - ENGLISH
Powering on/off
Connecting the power cord
Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily.
For details of power cord handling, refer to “Read this first!” (x page 2).
Attaching
1) Check the shapes of the terminal on the back of the projector bo\
dy and the power cord
connector and insert the plug completely in the correct direction.
AC IN xAC IN
Removing
1) Confirm that the projector is in standby mode, and remove...](http://img.usermanuals.tech/thumb/58/75999/w300_pt-tw343_en_om_d-33.png "Page 34
34 - ENGLISH
Powering on/off
Connecting the power cord
Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily.
For details of power cord handling, refer to “Read this first!” (x page 2).
Attaching
1) Check the shapes of the terminal on the back of the projector bo\
dy and the power cord
connector and insert the plug completely in the correct direction.
AC IN xAC IN
Removing
1) Confirm that the projector is in standby mode, and remove...")
34 - ENGLISH Powering on/off Connecting the power cord Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily. For details of power cord handling, refer to “Read this first!” (x page 2). Attaching 1) Check the shapes of the terminal on the back of the projector bo\ dy and the power cord connector and insert the plug completely in the correct direction. AC IN xAC IN Removing 1) Confirm that the projector is in standby mode, and remove...
Page 35
ENGLISH - 35 Powering On the Projector Before switching on the projector, make sure all the other devices are correctly connected. (x page 30) 2)1) 3) 3) 1) Connect the power cord to the projector body. 2) Connect the power plug to an outlet. fThe power indicator lights in red, and the projector will enter the standby mode. 3) Press the power button on the control panel or on the remote control. fThe power indicator blinks in red, after a while the indicator lights in green. (The factory default...
Page 36
![Page 36
36 - ENGLISH
Making adjustments and selections
It is recommended that images are projected continuously for at least 30\
minutes before the focus is adjusted.
3)
5)
3)
1) Adjust the focus of the image roughly. (x page 37)
2) Change the settings of the [Display] menu → [Project way] depending on the installation mode.
(x page 51)
fRefer to “Navigating through the menu” (x page 44) for the operation of the menu screen.
3) Press the button on the control panel or the input selecti\
on (,
, , , )...](http://img.usermanuals.tech/thumb/58/75999/w300_pt-tw343_en_om_d-35.png "Page 36
36 - ENGLISH
Making adjustments and selections
It is recommended that images are projected continuously for at least 30\
minutes before the focus is adjusted.
3)
5)
3)
1) Adjust the focus of the image roughly. (x page 37)
2) Change the settings of the [Display] menu → [Project way] depending on the installation mode.
(x page 51)
fRefer to “Navigating through the menu” (x page 44) for the operation of the menu screen.
3) Press the button on the control panel or the input selecti\
on (,
, , , )...")
36 - ENGLISH Making adjustments and selections It is recommended that images are projected continuously for at least 30\ minutes before the focus is adjusted. 3) 5) 3) 1) Adjust the focus of the image roughly. (x page 37) 2) Change the settings of the [Display] menu → [Project way] depending on the installation mode. (x page 51) fRefer to “Navigating through the menu” (x page 44) for the operation of the menu screen. 3) Press the button on the control panel or the input selecti\ on (, , , , )...
Page 37
![Page 37
ENGLISH - 37
Projecting
Check the connections of the peripheral devices (x page 30) and connection of the power cord (x page 34) and switch
on the power (x page 35) to start the projector. Select the image and adjust the state of the image.
Selecting the input signal
Select an input signal.
1) Press the button on the control panel or the input selecti\
on (, ,
, or ) buttons on the remote control.
fThe image of the signal being input in the selected terminal is projecte\
d.
Attention
fImages may...](http://img.usermanuals.tech/thumb/58/75999/w300_pt-tw343_en_om_d-36.png "Page 37
ENGLISH - 37
Projecting
Check the connections of the peripheral devices (x page 30) and connection of the power cord (x page 34) and switch
on the power (x page 35) to start the projector. Select the image and adjust the state of the image.
Selecting the input signal
Select an input signal.
1) Press the button on the control panel or the input selecti\
on (, ,
, or ) buttons on the remote control.
fThe image of the signal being input in the selected terminal is projecte\
d.
Attention
fImages may...")
ENGLISH - 37 Projecting Check the connections of the peripheral devices (x page 30) and connection of the power cord (x page 34) and switch on the power (x page 35) to start the projector. Select the image and adjust the state of the image. Selecting the input signal Select an input signal. 1) Press the button on the control panel or the input selecti\ on (, , , or ) buttons on the remote control. fThe image of the signal being input in the selected terminal is projecte\ d. Attention fImages may...
Page 38
![Page 38
38 - ENGLISH
Basic operations by using the remote control
Using the automatic setup function
Input search, Auto PC adjustment (during signal input from a computer) and Auto Keystone correction works at the same time.The Auto PC adjustment function can be used to automatically adjust the resolution, clock phase, and image position when analog RGB signals consisting of bitmap images such as computer signals \
are being input. Supplying images with bright white
borders at the edges and high-contrast black...](http://img.usermanuals.tech/thumb/58/75999/w300_pt-tw343_en_om_d-37.png "Page 38
38 - ENGLISH
Basic operations by using the remote control
Using the automatic setup function
Input search, Auto PC adjustment (during signal input from a computer) and Auto Keystone correction works at the same time.The Auto PC adjustment function can be used to automatically adjust the resolution, clock phase, and image position when analog RGB signals consisting of bitmap images such as computer signals \
are being input. Supplying images with bright white
borders at the edges and high-contrast black...")
38 - ENGLISH Basic operations by using the remote control Using the automatic setup function Input search, Auto PC adjustment (during signal input from a computer) and Auto Keystone correction works at the same time.The Auto PC adjustment function can be used to automatically adjust the resolution, clock phase, and image position when analog RGB signals consisting of bitmap images such as computer signals \ are being input. Supplying images with bright white borders at the edges and high-contrast black...
Page 39
![Page 39
ENGLISH - 39
Switching the aspect ratio of the image
You can switch aspect ratios according to the input signal.
button
1) Press the button on the remote control.
Note
fFor more details, refer to the [Display] menu → [Aspect] (x page 50).
Using the keystone distortion and curved correction functions
You can correct the trapezoidal distortion and the curved distortion of the projected image.
button
1) Press the button on the remote control.
fThe selection screen of keystone function is displayed....](http://img.usermanuals.tech/thumb/58/75999/w300_pt-tw343_en_om_d-38.png "Page 39
ENGLISH - 39
Switching the aspect ratio of the image
You can switch aspect ratios according to the input signal.
button
1) Press the button on the remote control.
Note
fFor more details, refer to the [Display] menu → [Aspect] (x page 50).
Using the keystone distortion and curved correction functions
You can correct the trapezoidal distortion and the curved distortion of the projected image.
button
1) Press the button on the remote control.
fThe selection screen of keystone function is displayed....")
ENGLISH - 39 Switching the aspect ratio of the image You can switch aspect ratios according to the input signal. button 1) Press the button on the remote control. Note fFor more details, refer to the [Display] menu → [Aspect] (x page 50). Using the keystone distortion and curved correction functions You can correct the trapezoidal distortion and the curved distortion of the projected image. button 1) Press the button on the remote control. fThe selection screen of keystone function is displayed....
Page 40
40 - ENGLISH Using the freeze function You can freeze the projected image and stop the sound temporarily, regardless of the playing condition of the external device. button 1) Press the button on the remote control. fThe video is paused and the audio is muted. The icon is displayed on the screen during Freeze. 2) Press the button again. fThe video playback resumes and the audio is unmuted. Note fWhen no signal input, the key operation is invalid and the icon will appear. Using the AV mute...